Tork DGS100A Bedienungsanleitung

INSTRUCTION MANUAL

MLI-198(B)

DIGITAL TIME SWITCH

7 DAY

DGS100A

DGS100A-12

DGS100A-24

FOR TECHNICAL SUPPORT:

888.500.4598

LISTED

888.500.4598 • www.nsiindustries.com

TABLE OF CONTENTS

Section Page

Installation Instructions and

Capabilities ...........................1

1.0 Clock Format . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.0 Clock Set Mode . . . . . . . . . . . . . . . . . . . . . . . . 2

3.0 Date Set Mode .........................2

4.0 Daylight Saving Time.....................3

4.1 To Modify Daylight Savings Dates ............3

5.0 Duty cycle and Signal . . . . . . . . . . . . . . . . . . . . 4

5.1 To set Duty cycle and Signal ................5

6.0 Schedule Set Mode ......................6

6.1 Setting Hours, Minutes, and Days ............6

7.0 Review, Modify, and Delete . . . . . . . . . . . . . . . . 8

Override Mode.........................8

Wiring Diagram .......................11

Schedule Sheets . . . . . . . . . . . . . . . . . . . . 12, 13

TORK MODEL

DGS100A/DGS100A-12/DGS100A-24

7 DAY DIGITAL TIME SWITCH

READ INSTRUCTIONS CAREFULLY BEFORE

ATTEMPTING TO INSTALL TIME SWITCH. SEE

WARNING ON FRONT PANEL – Failure to comply with

instructions could result in personal injury and/or property

damage.

INSTALLATION:

UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN

1. Remove unit from enclosure by pushing the inside

tab (located near the outside hasp) to the right.

Swing unit to left and remove.

2. Mount the enclosure at eye level using screws

or other suitable fastening device. Bring supply

and load wires in through or side knockouts.

DO NOT USE TOP.

3. Reinstall unit by reversing step #1 above and

connecting wires to units as per suggested

wiring diagrams at back of manual.

4. Unit should be programmed with AC power. Do

not program under super cap back up power.

AT POWER UP;

Connect unit to main power source prior to entering the

settings. When powering up the unit for the ﬁrst time,

allow 1-2 minutes for super cap to charge and the

display will show 12 HOUR. Press reset button after 2

minutes if screen is blank.

CAPABILITIES

- 7 day scheduling

- 56 set points

- 2 Duty cycle or signal durations

FEATURES

Daylight saving - Automatic (user selectable)

Leap year - Automatic compensation

Power outage - Permanent schedule retention. Super

capacitor provides 7 days of real time back up.

Manual override - Until the next scheduled event

AM/PM or 24 hour format - user selectable

Multi-Voltage Input: 120 – 277VAC

1.0 CLOCK FORMAT

The ﬁrst time unit is powered up, it will display a

ﬂashing 12 Hour. Use HOUR key to set clock format to

either 12 Hour (AM/PM) or 24 Hour. Press the ENTER

key.

2.0 CLOCK SET MODE

Press HOUR and MIN to advance to the present hour

and minutes. Check AM/PM, and press ENTER.

3.0 DATE SET MODE

Press MONTH, DATE, and YEAR key to advance to

the desired month, date and year, then press ENTER.

NOTE: The day of the week will automatically set

once the date is entered.

4.0 DAYLIGHT SAVING TIME

After setting or modifying the date, display will show:

a. For standard USA daylight savings (DSt), press

MODE and go to step 5.0.

b. For dates other than standard USA dates, press

MONTH and go to step 4.1.

c. If daylight saving time (DSt) is NOT required, press

DEL display will show:

Press ENTER then go to step 5.0.

4.1 TO MODIFY STANDARD USA DAYLIGHT SAV-

INGS DATES

NOTE: The ﬁrst two digits represent the month and

the second set of digits represent the week in the

month. Choices for week are 01 (1st), 02 (2nd), 03

(3rd) or L (Last) week of the month. The default day

is Sunday (SU.) Once modiﬁed date set, the unit will

automatically calculate the correct start dates in the

future.

Now press MONTH and DATE buttons to modify the

starting DST settings. Pressing DAY changes default

day. EXAMPLE: A screen showing “04:01 SU S”

represents April (04), the ﬁrst week (01), Sunday (SU),

and the Start (S) of daylight savings time.

Press ENTER to save and the display will show:

Now press MONTH and DATE buttons to modify the

ending DST settings. Pressing DAY changes default

day. EXAMPLE: A screen showing “10: L SU E”

represents October (10), the Last week (L), Sunday

(SU), and the End (E) of daylight savings time.

Press ENTER to save and the display will show the

modiﬁed DSt starting date.

Press MODE twice to go to step 5.0.

5.0 DUTY CYCLE AND SIGNAL

The Duty Cycle programming mode begins with a

display that shows the ON duration ﬁrst for Duty Cycle

1 and the OFF duration second. Programming both

ON and OFF will enable the load to repeatedly turn

ON then OFF.

The Signal Timer operation can be used by setting only

the ON duration of each duty cycle. Skip the OFF

duration entry. The load will turn ON for the duration of

the ON period, and it will not be repeated.

Once you’ve selected a cycle time, you need to

program the schedule in Section 6.0. Schedule the

events whenever you need to start and end the duty

cycle or to execute a signal, such as school bells.

To skip, press the MODE key.

5.1 TO SET DUTY CYCLE AND SIGNAL

Press the ENTER key.

Press either HOUR, MIN, or SEC keys to set the time

to the desired ON duration for the cycle (ON C1).

Press the ENTER key.

a) For signal timer application, press the ENTER key.

b) For a cycle program, press the HOUR, MIN, or SEC

keys to set the time to the desired OFF duration for

the cycle (OFF C1). Press the ENTER key.

Follow the same procedures above to set the second

signal or duty cycle entries.

Press MODE key to advance to next screen.

6.0 SCHEDULE SET MODE

Press MODE key until display shows:

6.1 SETTING HOURS, MINUTES, AND DAYS

Note: A schedule is needed for each event. If a typical

ON/OFF pair is required, use SCH 01 for the ON

event and SCH 02 for the OFF event.

Press the HOUR, and MIN keys to set the desired time.

Press EVENT to set desired event

(ON or OFF, C1, or C2)

Note: C1 or C2 will not be displayed if the duty cycle

durations are not set in Step 5.

Press DAY to set desired day(s).

Note: With each DAY button push a different group of

days will appear.

Press ENTER to save.

Follow the same procedures above to set more

schedule entries.

Press MODE when schedules are complete.

Unit is in the AUTO (automatic) mode.

The word FLASH may appear to indicate a new

program has been written to memory.

Press the EVENT key once to activate current

schedule then EVENT key again to return to AUTO

mode.

7.0 REVIEW, MODIFY AND DELETE

Press MODE to advance to any of the following

MODES:

1. AUTO MODE: In this automatic mode, the unit will

execute the scheduled programs. Time, day, seconds

and load status are displayed. C1is displayed when

Duty Cycle is programmed and operating.

OVERRIDE IN AUTO MODE: The load status of the

channel can be manually changed by pressing the

OVRD key. The unit will stay in this position until the

next scheduled event. A ﬂashing LCD load indication

(ON, OFF) shows the status was changed by the

override not a scheduled event. Press the OVRD key

until ON or OFF stops ﬂashing to return to programmed

setting.

2. MAN MODE: In this manual mode, the unit will

ignore the schedule programs. Time, day, seconds

and load status are displayed. This can be used as a

VACATION SETTING to keep load off while away. Use

override to set to OFF position.

OVERRIDE IN MAN MODE: The load status of the

channel can be manually changed by pressing the

OVRD key. The unit will stay in this position until

OVRD is pressed again. A ﬂashing LCD load

indication (ON, OFF) shows the status was changed by

the override not a scheduled event.

3. CLOCK MODE: Press HOUR and MIN to modify

existing settings. Press ENTER to save changes.

4. DATE MODE: Press MONTH, DATE and YEAR to

modify existing settings. Press ENTER to save

changes. DAY is automatically adjusted.

5. DSt MODE: Factory default is set at US standard

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tork Timer Handbücher

Beliebte Timer Handbücher anderer Marken

Intermatic

Intermatic P1131 Bedienungsanleitung

Learning Resources

Learning Resources Time Tracker mini Bedienungsanleitung

CEBEK

CEBEK I-215 Bedienungsanleitung

Somogyi

Somogyi home TS MD 5 Bedienungsanleitung

Profile

Profile 010200280 Bedienungsanleitung

Gizmo

Gizmo T4 Bedienungsanleitung

Tekmar

Tekmar Timer 031 Bedienungsanleitung

Daikin

Daikin DST301B61 Bedienungsanleitung

sisel

sisel ENDA ETM2432 Bedienungsanleitung

B&Q

B&Q TE103 Bedienungs- und Wartungshandbuch

Hozelock

Hozelock AC Plus 2700 Bedienungsanleitung

GIC

GIC Eliro V7DDSS3Eliro V7DFTS3 Bedienungsanleitung

Emos

Emos EMT400F Bedienungsanleitung

FarmTek

FarmTek Polaris Bedienungsanleitung

Maximum

Maximum CRONUS Bedienungsanleitung

Uberhaus

Uberhaus TD133B Bedienungsanleitung

Clas Ohlson

Clas Ohlson 31-3766 Bedienungsanleitung

Gewiss

Gewiss 90 AM Series Bedienungsanleitung