Tormach 33272 Technisches Handbuch
TECHNICAL DOCUMENT
TORMACH.COM
Page 1
©Tormach® 2017. All rights reserved.
Specicaons subject to change without noce.
TD10246_Tool_Post_Install_0317A
Quick ChangeTool Post Installation
Product Idencaon: Quick Change Tool Post Kit (PN 33272)
Purpose: This document details the installaon and use of the Quick Change Tool Post Kit on a 15L Slant-PRO™
Lathe.
Qty. Quick ChangeTool Post Kit Size PN
1 Quick Change Tool Post CXA 34129
1 Tool Post Handle —
2 #2 Tool Holder for Quick Change Post CXA 33124
2 #1 Tool Holder for Quick Change Post CXA 33123
1 #4 Tool Holder for Quick Change Post CXA 33125
1 Quick Change Tool Mount Plate — 33202
4 M8 x 40 mm Socket Head Screw —
NOTE: If any of these items are missing, contact Tormach Customer
Service at (608) 849-8381 for a replacement.
RequiredTools and Items:
• Dead-blow hammer
• Metric hex wrench set
• Rust preventative
• Adjustable wrench
• Magnetic dial test indicator
Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 2
©Tormach® 2017. All rights reserved.
Specicaons subject to change without noce.
TD10246_Tool_Post_Install_0317A
Installation
1. Remove Mounng Block from boom of Tool
Post and discard. Mounng Block is shown in
Figure 1.
2. Inspect surfaces of both carriage and Tool
Mount Plate; remove burrs, wipe o grit
and dirt. If necessary, use hand-held stone
to deburr surface. Spray surfaces with rust
preventave such as WD40®.
3. Posion Tool Mount Plate on lathe carriage;
using four M8 x 40 mm Socket Head Screws,
aach plate to lathe carriage (see Figure 2).
Figure 1
Figure 2
Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 3
©Tormach® 2017. All rights reserved.
Specicaons subject to change without noce.
TD10246_Tool_Post_Install_0317A
4. Screw Tool Post Stud into plate and ghten
snug (see Figure 3).
5. Slide Tool Post over stud. Aach Nut and hand
ghten (see Figure 4). Screw Tool Post Handle
into Tool Post.
6. Match up desired Tool Holder with the desired
tool (see Figure 5).
Figure 3 Figure 4
Figure 5
Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 4
©Tormach® 2017. All rights reserved.
Specicaons subject to change without noce.
TD10246_Tool_Post_Install_0317A
7. Lock tool into Tool Holder by ghtening hex-
head screws in sequence shown in Figure 6
and Figure 7.
8. Adjust Thumb Screw to set Tool Holder height;
secure with Stop Nut (see Figure 8).
Figure 6
1 23 4
Figure 7
Figure 8
Stop Nut
Thumb Screw
Spring Washer
Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 5
©Tormach® 2017. All rights reserved.
Specicaons subject to change without noce.
TD10246_Tool_Post_Install_0317A
9. Swing Tool Post Handle up to unlocked posion (see Figure 9).
NOTE: Tool Post lever must be in unlocked posion to aach holder.
10. Slide Tool Holder onto Tool Post dove tail (see Figure 9). Swing Tool Post Handle down to locked posion.
11. Aach magnec dial test indicator to spindle. Posion indicator p against tool face. Power up lathe and
move carriage back and forth on X-axis against indicator p (see Figure 10).
12. To correct Tool Post misalignment, tap with dead-blow hammer to adjust, as necessary (see Figure 10).
Repeat Steps 11 and 12 unl suitable alignment is achieved.
13. Tighten Tool Post nut securely with adjustable
wrench (see Figure 11).
14. Recheck tool with dial indicator to ensure
posion did not change following ghtening of
nut.
Figure 9
Locked
Unlocked
Figure 10
Figure 11
Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 6
©Tormach® 2017. All rights reserved.
Specicaons subject to change without noce.
TD10246_Tool_Post_Install_0317A
Boring Bar Holder Useage
1. Insert desired tool into Boring Bar Holder
and lock tool by ghtening two hex-head cap
screws (see Figure 12).
2. Move Tool Post lever to the unlocked posion
and slide Boring Bar Holder onto the QCTP
dove tail (see Figure 13); swing Tool Post lever
down to locked posion.
3. To change tools, loosen hex cap screws on
Boring Bar Holder.
4. Tap both hex-head cap screws with dead-blow
hammer to release tool (see Figure 14).
NOTE: Reducer Sleeve (3/4”-1”), located inside the
Boring Bar Holder, is included.
Figure 12 Figure 13
Figure 14
Inhaltsverzeichnis
Andere Tormach Werkzeuge Handbücher
