Tornado HI-FAN-16WMPRO-1P Bedienungsanleitung

Tornado-Metal Wall Fan

HI-FAN-16WMPRO-1P

HI-FAN-20WMPRO-1P

BEFORE YOU BEGIN

When using electrical appliances, basic precautions should

always be followed to avoid the risk of fire, electric shock and

injury to persons. So please

READ FOLLOWING INSTRUCTIONS CAREFULLY BEFORE

OPERATION.

1. Only use this fan as described in this manual, other

non-recommended use may cause fire, electric shock, or injury.

2. To protect against electrical shock, do not immerse unit plug

or cord In water or spray with liquids

3. Only plug the unit into a power outlet with the same voltage as

rated voltage of it.

3. Keep the fan out of the reach of children. This fan is not for

use by children.

4. Do not leave the fan running unattended

5. Never insert fingers, pencils or any other object through the

guards when fan is running.

6. Do not operate in the presence of explosive and/or flammable

fumes.

7. Unplug the plug when move the unit from one location to

another.

8. Unplug the plug when open the guard grilles for cleaning.

9. Do not immerse or expose the Motor Housing, Power Cord, or

Plug to water or other liquids. Do not use the fan near a

bathtub, a shower, a swimming pool, or anywhere water could

splash.

10. Do not plug/unplug the fan into/from the electrical outlet with

wet hand.

11. Never operate the fan without fan guard in place, as serious

personal injury may result.

12. Indoor use only, Do not use outdoor. Do not place the fan in or

near window. rain may create an electrical hazard.

13. To disconnect, grip plug and pull from wall outlet. Never yank

on cord.

16. To avoid fall down causes injury or damage, only operate the

unit after it is firmly mounted on a strong flat wall surface.

17. WARNING:To reduce the risk of fire or electric shock, DO NOT

use this fan with any solid-state speed control devices.

1. If the power cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified person

in order to avoid a hazard.

2. This product employs overload protection (fuse). A blown fuse

indicates an overload or short-circuit situation. If the fuse

blows, unplug the product from the outlet. Replace the fuse as

per the user servicing instructions (follow product marking for

proper fuse rating) and check the product. If the replacement

fuse blows, a short-circuit may be present and the product

should be discarded or returned to an authorized service

facility for examination and/or repair.

3. Do not operate any fan with a damaged cord or plug. Discard

fan or return to an authorized service facility for examination

and/or repair.

4. Do not run cord under carpeting. Do not cover cord with throw

rugs, runners, or similar coverings. Do not route cord under

furniture or appliances. Arrange cord away from traffic area

and where it will not be tripped over.

POWER CORD & PLUG REQUIREMENTS:

ASSEMBLE THE FAN

1. Rear grill assembly

WARNING: Before use the fan, must assemble it by joining

every individual parts firmly together, and follow the steps

below for the work.

2-1. Unscrew the screw on the front of the motor (Fig. 1-A for HI-FAN-16WMPRO-1P,

Fig.1-B for HI-FAN-20WMPRO-1P).

2-2. Place the rear grill against the motor housing（Fig.1 & Fig.2）

2-3. Align the holes with the screw holes on the housing, then tighten the screw to

secure the rear grill to the motor (Fig.1 & Fig.2)

Fig.1-A for HI-FAN-16WMPRO-1P

-A

3-1. Remove the nut from the motor shaft (Fig.2)

3-2. Slide the propeller onto the motor shaft by aligning its slot with the pin in the

shaft (Fig.2)

3-3. Secure the propeller with the nut. (Fig.2)

3. Propeller assembly

-B

Fig.1-B for HI-FAN-20WMPRO-1P

4. Front grill assembly

4-1. Remove the screw and nut in the bottom of the front grill (Fig.3)

4-2. Place the front grill against the rear grill with its top buckle encase

the rim of the rear grill, then turn all other buckles encasing the rim also.(Fig.3)

4-3. Tighten the two grills with screw and nut again. (Fig.3)

I. FIX FAN ON WALL

WARNING: Before use the fan, must fix it firmly on a strong flat wall surface,

and follow the steps below for the work.

1. Draw a vertical line on wall ( Fig. 4)

2. Drill three holes in the vertical line with a diameter as that of the wall plugs

provided. space between two holes is 6.4 cm. (Fig.5).

3. Insert each hole a wall plug . ( Fig.6)

4. Put bracket on wall, align its three holes at three wall plugs (Fig.6 )

5. Drive three tapping screws provided through the three holes of the bracket into

the wall plug and secured it firmly against the wall .(Fig.6)

6. Drive two screws provided ( M4 ) into two upper holes in the bracket, leaving a

gap of 5mm between the screw head and the bracket (Fig. 7)

7. Hang on wall the unit align its two key holes at two screws in bracket .(Fig.8)

8. Drive two screws provided ( M4 ) through the low two holes of the base into the

bracket and secured the unit firmly against the bracket.(Fig.8)

9. Tighten the two upper screws through the base upper hole also.(Fig.8)

Now the unit is ready for use.

III. OPERATION

The unit can be used alone or in conjunction

with an air conditioner unit to circulate already

cooled air or force it into other rooms.

1. To operate the fan, slide the speed control

bar to High “3”, for strong wind, Low ”1” for

mild one, or Medium ”2” for wind between

them. To turn off the fan, slide the speed

control bar to off position “0”. (Fig.9)

2. When turn on, the unit can also be oscillation by pushing down the knob at top of

its head or still in any position by pulling the knob up ( Fig.8)

3. To adjust the tilt of the unit you should loosen the screw knob at the right first,

then turn up or down the unit head to the desire angle, tighten again the screw

knob. ( Fig.8 )

It is normal for the motor to feel warm to the touch during operation. The motor is

thermally protected and will automatically shut off should it overheat for any reason.

If this happens, immediately disconnect the fan from the power outlet.

6. Drive two screws provided ( M4 ) into two upper holes in the bracket, leaving a

gap of 5mm between the screw head and the bracket (Fig. 7)

7. Hang on wall the unit align its two key holes at two screws in bracket .(Fig.8)

8. Drive two screws provided ( M4 ) through the low two holes of the base into the

bracket and secured the unit firmly against the bracket.(Fig.8)

9. Tighten the two upper screws through the base upper hole also.(Fig.8)

CLEANING / MAINTENANCE INSTRUCTIONS

ATTENTION

FAN BLADE & FRONT GRILL CLEANING

User Servicing Instructions

Follow these instructions to correctly and safely care for your unit..

1. Always unplug the fan before cleaning or disassembling.

2. Do not allow water to drop on or enter into fan housing.

3. Be sure to use a soft cloth moistened with a mild soap solution.

4. Do not use any of the following as a cleaner. Gasoline, thinner, Or benzene.

1. Remove the screw and nut at the bottom of front grill,

2. Turn open all buckles at the rim of the grill and remove the front grill.

3. Clean the fan blade and grill with a soft damp cloth. DO NOT ATTEMPT TO

REMOVE THE FAN BLADE. Do not allow the motor or other electrical

components to be exposed to water.

4. Replace front grill and secure with the screw and nut removed in the first step.

5. Turn all buckles back to the rim.

Grasp plug and remove from the receptacle or other outlet device. Do not unplug

by pulling on cord.

Open fuse cover. Slide open fuse access cover on top of attachment plug

towards blades.

Turn fuse holder over to remove fuse. Remove fuse carefully.

Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse(provided with product).

Close fuse cover. Slide closed the fuse access cover on top of attachment plug.

Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that

should not be removed. Discard product if the attachment plug is damaged.

Tornado Fans warrants this product to be free of defects in material and workmanship for the

applications specified in the Owner's Manual for a period of 12 months for the whole fan from the

date of purchase. This warranty only applies to the original purchaser of this product.

This warranty excludes damage, accidental or otherwise, to the unit not caused by a defect in

material or workmanship.

The warranty also exlcudes damage caused by misuse, tampering, modification, missassembly, repairs

or alternations, or failure to adequately maintain and care for the unit. Operating this product under any

conditions others than those recommended or at voltages other than indicated will also void this warranty.

For warranty issues, contact the place of purchase for repair/ replacement opportunities. The original

dated receipt or proof of purchase must accompany all returns.

All warranties, expressed or implied, are limited for 12 months for the whole fan from the date of

purchase. Please register at www.tornado-fans.com/registration once you received the products to

get the extended warranty if there is any. Tornado is a registered trademark.

Some states do not allow for the limitation or exclusion of incidental or consequential damages, or do

not allow limitation on implied warranties. The above limitations and exclusions may not apply to you.

This warranty gives you specific legal rights, and may also include other rights that vary state by state.

ONE

Andere Handbücher für HI-FAN-16WMPRO-1P

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tornado Lüfter Handbücher

Tornado

Tornado HI-FAN-24POF-WR-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-16WMPRO-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-18HVWM-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-20HVWM- WR-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-30POF- WR-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-24HVWM- WR-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-20WMPRO-1P Bedienungsanleitung

Tornado

Tornado SFS1-500B3IW Bedienungsanleitung

Tornado

Tornado HI-FAN-24MOWF-WR-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-18HVWM-WR-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-30MOWF-A-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-SEF10-1PK Bedienungsanleitung

Tornado

Tornado HI-FAN-30HVF-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-DRUM24W-1 P Bedienungsanleitung

Tornado

Tornado HI-FAN-24MOWF-A-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-24POF- 1P Bedienungsanleitung

Tornado

Tornado HI-FAN-30HVOF-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-30MOWF-WR-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-24HVWM-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-W16DIGIT-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-20POF-5BA-1P Bedienungsanleitung

Tornado

Tornado HI-FAN-20HVWM-A-1P Bedienungsanleitung

Tornado

Tornado Windshear 98782 Handbuch

Tornado

Tornado HI-FAN-DRUM24-1 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung