Toro 22442 Bedienungsanleitung

The T

oro Company

– 1999

8111 Lyndale Ave. South

Printed in the USA

Form No. 3323-285

Model 22442

Cement Mixer Bowl

For use with the Siteworks Systems Auger Drive Head

Installation

Instructions

IMPORTANT:

Befor

e using this pr

oduct, read the

safety section in your traction unit operator

’

s manual,

and follow all pr

ecautions listed ther

Safety

Decals

100–4664

Figure 1

1. Tipping

hazard—do not

exceed

the maximum

load

2. Maximum

load

Specifications:

Note:

Specifications and design are subject to change

without notice.

Overall

width

25.15 inches (64 cm)

Overall length

18.25 inches (46 cm)

Weight

75 lbs (34 Kg)

Maximum dry concrete

load

200 lbs (90.7 Kg)

Stability

Ratings

determine the degree of slope you can traverse with the

cement bowl installed on a traction unit, find the stability

rating for the hill position you want to travel in the

appropriate table on the following page, then find the

degree of slope for the same rating and hill position in the

Stability Data section of the traction unit operator

’s

manual.

IMPORTANT

: If your traction unit has a r

ear

operator’

s platform, the counterweight must be used

on the platform while using the cement bowl, or the

traction unit will become unstable.

WARNING

POTENTIAL HAZARD

•

Exceeding the maximum r

ecommended slope

can cause the traction unit to tip.

WHA

T CAN HAPPEN

•

If the traction unit tips, you or bystanders could

be crushed.

HOW T

O A

OID THE HAZARD

•

Do not drive the traction unit on a slope steeper

than the maximum r

ecommended slope, as

determined in the following tables and the

traction unit operator

’

s manual.

Installation Instructions

Stability with a Loaded Bowl

Orientation Stability Rating

Front Uphill B

Rear Uphill

Side Uphill

Stability with an Unloaded Bowl

Orientation Stability Rating

Front Uphill C

Rear Uphill

Side Uphill

Installing

the Bowl onto the

Auger Drive Head

1. Raise

the loader arms so the drive head clears the

ground and stop the engine

Manually rotate the auger drive head up, until you can

install two bolts into the holes on both sides of the

cradle arms, securing the drive head. Secure each bolt

with a nut (Fig. 2).

m–3944

Figure

1. Drive

head

Cradle arm

Bolts and nuts

3. Start

the engine.

Maneuver the drive shaft into the collar on the back of

the bowl (Fig. 3).

m–4316

Figure

1. Drive

head

Cement bowl

5. Stop

the engine.

Secure the bowl to the drive head with the bolt and nut

supplied with the auger drive head (Fig. 4).

m–4317

Figure

1. Bolt 2. Nut

Installation Instructions

Mixing

and Pouring Concrete

POTENTIAL

HAZARD

•

When full of concr

ete, the bowl is very heavy

and could unbalance the traction unit.

WHA

T CAN HAPPEN

•

The traction unit could tip, seriously injuring

you or bystanders.

HOW T

O A

OID THE HAZARD

•

Never use the cement bowl on the Dingo

without first installing the Sitework Systems

Counterweight, available fr

om your T

oro

dealer.

•

Always keep the bowl close to the gr

ound.

Lower the loader arms as far as possible while tilting

the bowl upward as far as possible.

Add up to 200 lbs (90.7 Kg) of dry concrete mixture.

Move the throttle lever to the fast position (rabbit).

If your traction unit has a speed selector and flow

divider

, move the speed selector lever to fast (Rabbit),

and the flow divider control to the 10 to 11 o’clock

position (20 to 30 RPM).

Push the auxiliary hydraulics lever away from the

operator grip to mix the concrete and add the

appropriate amount of water

When the cement is suf

ficiently mixed, move the

auxiliary hydraulics lever to neutral and drive slowly

to the work site.

7. T

ilt the bowl forward and pull the auxiliary hydraulics

lever to the operator grip and hold it to dump the

concrete.

When finished using the bowl, wash it out before the

concrete sets.

Removing

the Bowl from the

Auger Drive Head

1. Set

the bowl down in its storage location.

Stop the engine.

Remove the bolt and nut securing the drive head to the

bowl.

Start the engine and back the traction unit away from

the bowl.

Storage

Before long term storage, wash the bowl with mild

deter

gent and water to remove dirt and grime.

Store the bowl in a clean, dry garage or storage area.

Cover it to protect it and keep it clean.

Andere Handbücher für 22442

Andere Toro Baumaschinen Handbücher

Toro

Toro MM E-S Series Bedienungsanleitung

Toro

Toro 23174 Bedienungsanleitung

Toro

Toro CM Series Bedienungsanleitung

Toro

Toro 22984HD Bedienungsanleitung

Toro

Toro MMX-658H-P Bedienungsanleitung

Toro

Toro VR-2650 Bedienungsanleitung

Toro

Toro 323 Bedienungsanleitung

Toro

Toro TX 700 Bedienungsanleitung

Toro

Toro MMX-650E-S Bedienungsanleitung

Toro

Toro 2024 Kurzanleitung

Toro

Toro Line Painter 1200 Bedienungsanleitung

Toro

Toro 22322 Bedienungsanleitung

Toro

Toro TRX-250 Bedienungsanleitung

Toro

Toro TX 525 Installations- und Betriebsanleitung

Toro

Toro 22409 Bedienungsanleitung

Toro

Toro 68037 Bedienungsanleitung

Toro

Toro TXL 2000 Bedienungsanleitung

Toro

Toro MMX-658H-S Bedienungsanleitung

Toro

Toro MMX-658K-P Bedienungsanleitung

Toro

Toro 22910 Bedienungsanleitung

Toro

Toro Line Painter 1200 Bedienungsanleitung

Toro

Toro MMX-650E-S Bedienungsanleitung

Toro

Toro MMX-1158H-S Bedienungsanleitung

Toro

Toro CM-658H-S Bedienungsanleitung

Beliebte Baumaschinen Handbücher anderer Marken

SASFORKS

SASFORKS EXTREME Bedienungsanleitung

Hailo

Hailo H-50 Bedienungsanleitung

Graco

Graco LineLazer ES 1000 Gebrauchs- und Pflegehandbuch

Greenlee

Greenlee 555RSC Bedienungsanleitung

Manitowoc

Manitowoc Grove CD3340B Bedienungsanleitung

Lux Tools

Lux Tools A-FMR-20 Set Bedienungsanleitung

SIP

SIP 03683 Bedienungsanleitung

Volvo

Volvo L30G Bedienungsanleitung

Grizzly

Grizzly G8712 Bedienungsanleitung

Modulift

Modulift CMOD 12 Bedienungsanleitung

Case

Case DV201 Bedienungsanleitung

Sealey

Sealey SC10.V2 Bedienungsanleitung

Wacker Neuson

Wacker Neuson DT05 Bedienungsanleitung

HYVA

HYVA AMCO VEBA 81 Series Bedienungsanleitung

Atlas Copco

Atlas Copco Dynapac V5100TV Bedienungsanleitung

Manitowoc

Manitowoc National Crane 1400A Bedienungsanleitung

SGS

SGS EC1500 Bedienungsanleitung

Saferoad

Saferoad VR Arcus Primus 90 Series Bedienungsanleitung