Toro 30241 Groundsmaster 228-D Bedienungsanleitung

Form No. 3325-387 Rev A

Operator’s Manual

Groundsmaster®228-D

Traction Unit

Model No. 30241—210000001 and Up

English

Contents 2
Introduction 3
Safety 3
Safe Operating Practices 3
Toro Mower Safety 5
Safety and Instruction Decals 8
Specifications 12
Installing Rear Weights 14
Before Operating 15
Check the Engine Oil 15
Check the Cooling System 15
Check Hydraulic System Fluid 15
Fill the Fuel Tank 16
Controls 17
Operation 20
Starting/Stopping the Engine 20
Bleeding the Fuel System 20
Checking the Interlock System 21
Operating Characteristics 22
Pushing or Towing the Traction Unit 22
Maintenance 23
Recommended Maintenance Schedule 23
Fluid Specifications/Change Intervals 24
Service Interval Charts 24
Daily Maintenance Checklist 25
General Air Cleaner Maintenance 27
Servicing the Air Cleaner 27
Cleaning the Radiator and Screen 28
Changing the Engine Oil and Filter 28
Servicing the Fuel System 28
Replacing the Fuel Pre Filter 29
Bleeding Air from Injectors 30
Alternator Belt 30
Adjusting the Throttle 30
Power Take-Off Belt 30
Power Take-Off Clutch Adjustment 31
Adjusting the Transmission for Neutral 31
Adjusting the Parking Brake 
Interlock Switch 32
Changing the Hydraulic Oil and Filter 33
Adjusting the Service Brakes 34
Servicing the Battery 34
Wiring Harness Service 34
Fuses 34
Storage 35
2
Contents
2001 by The Toro Company 8111 
Lyndale Avenue South 
Bloomington, MN 55420-1196 
All Rights Reserved 
Printed in the USA

Read this manual carefully to learn how to operate

and maintain your product properly. The information

in this manual can help you and others avoid injury

and product damage. Although Toro designs and

produces safe products, you are responsible for

operating the product properly and safely.

Whenever you need service, genuine Toro parts, or

additional information, contact an Authorized Service

Dealer or Toro Customer Service and have the model

and serial numbers of your product ready. Figure 1

illustrates the location of the model and serial

numbers on the product.

Figure 1

1. Location of the model and serial numbers

Write the product model and serial numbers in the

space below:

This manual identifies potential hazards and has

special safety messages that help you and others avoid

personal injury and even death. Danger, Warning, and

Caution are signal words used to identify the level of

hazard. However, regardless of the hazard, be

extremely careful.

Danger signals an extreme hazard that will cause

serious injury or death if you do not follow the

recommended precautions.

Warning signals a hazard that may cause serious

injury or death if you do not follow the recommended

precautions.

Caution signals a hazard that may cause minor or

moderate injury if you do not follow the

recommended precautions.

Safety

This machine meets or exceeds the B71.4 1999

specifications of the American National Standards

Institute when weights are installed according to

chart on page 14.

Note: The addition of attachments made by other

manufacturers that do not meet American National

Standards Institute certification will cause

noncompliance of this machine.

Improper use or maintenance by the operator or

owner can result in injury. To reduce the potential

for injury, comply with these safety instructions

and always pay attention to the safety alert symbol

, which means CAUTION, WARNING, or

DANGER—personal safety instruction.” Failure

to comply with the instruction may result in

personal injury or death.

Safe Operating Practices

Training

•Read the Operator’s Manual and other training

material. If the operator(s) or mechanic(s) cannot

read the language of the manual, it is the owner’s

responsibility to explain this material to them.

•Become familiar with the safe operation of the

equipment, operator controls, and safety signs.

•All operators and mechanics should be trained.

The owner is responsible for training the users.

•Never let children or untrained people operate or

service the equipment. Local regulations may

restrict the age of the operator.

•The owner/user can prevent and is responsible

Introduction

Model No. __________________________

Serial No. ___________________________

for accidents or injuries occurring to himself or

herself, other people or property.

Preparation

•Evaluate the terrain to determine what

accessories and attachments are needed to

properly and safely perform the job. Only use

accessories and attachments approved by the

manufacturer.

•Wear appropriate clothing including hard hat,

safety glasses and ear protection. Long hair, loose

clothing or jewelry may get tangled in moving

parts.

•Inspect the area where the equipment will be

used and remove all objects such as rocks, toys

and wire that can be thrown by the machine.

•Use extra care when handling diesel and other

fuels. They are flammable and vapors are

explosive.

•Use only an approved container

•Never remove the fuel cap or add fuel with

the engine running. Allow the engine to cool

before refueling. Do not smoke.

•Never refuel or drain the machine indoors.

•Check that operator’s presence controls, safety

switches and shields are attached and functioning

properly. Do not operate unless they are

functioning properly.

Operation

•Never run an engine in an enclosed area.

•Only operate in good light, keeping away from

holes and hidden hazards.

•Be sure all drives are in neutral and the parking

brake is engaged before starting the engine. Only

start the engine from the operator’s position. Use

seat belts, if provided.

•Slow down and use extra care on hillsides. Be

sure to travel in the recommended direction on

hillsides. Turf conditions can affect the machine’s

stability. Use caution while operating near

drop–offs.

•Slow down and use caution when making turns

and when changing directions on slopes.

•Never raise the deck with the blades running.

•Never operate with the power take-off shield, or

other guards not securely in place. Be sure all

interlocks are attached, adjusted properly, and

functioning property.

•Do not change the engine governor setting or

overspeed the engine.

•Stop on level ground, lower the implements,

disengage the drives, engage the parking brake

(if provided), and shut off the engine before

leaving the operator’s position for any reason.

•Stop the equipment and inspect the blades after

striking objects or if an abnormal vibration

occurs. Make necessary repairs before resuming

operations.

•Keep your hands and feet away from the cutting

units.

•Look behind and down before backing up to be

sure of a clear path.

•Never carry passengers and keep pets and

bystanders away.

•Slow down and use caution when making turns

and crossing roads and sidewalks. Stop the

blades if not mowing.

•Do not operate the mower under the influence of

alcohol or drugs

•Use care when loading or unloading the machine

into a trailer or truck

•Use care when approaching blind corners,

shrubs, trees, or other objects that may obscure

vision.

Maintenance and storage

•Disengage the drives, lower the implement, set

the parking brake, stop the engine and remove

the key. Wait for all movement to stop before

adjusting, cleaning or repairing.

•Clean grass and debris from the cutting units,

drives, mufflers, and engine to help prevent fires.

Clean up oil or fuel spillage.

•Let the engine cool before storing and do not

store near flame.

•Do not store fuel near flames or drain indoors.

•Park the machine on level ground. Never allow

untrained personnel to service the machine.

•Use jack stands to support components when

required.

•Carefully release pressure from components with

stored energy.

•Disconnect the battery before making any

repairs. Disconnect the negative terminal first

and the positive last. Reconnect positive first and

negative last.

•Use care when checking the blades. Wrap the

blade(s) or wear gloves, and use caution when

servicing them. Only replace the blades. Never

straighten or weld them.

•Keep your hands and feet away from moving

parts. If possible, do not make adjustments with

the engine running.

•Charge batteries in an open well ventilated area,

away from spark and flames. Unplug charger

before connecting or disconnecting from the

battery. Wear protective clothing and use

insulated tools.

•Keep all parts in good working condition and all

hardware tightened. Replace all worn or damaged

decals.

Toro Mower Safety

This product is capable of amputating hands and feet

and throwing objects. Always follow all safety

instructions to avoid serious injury or death.

This product is designed for cutting and recycling

grass. Any use for purposes other than these could

prove dangerous to user and bystanders.

General Operation

•Allow only responsible adults who are familiar

with the instructions to operate the machine.

•Be sure the area is clear of other people before

mowing.Stop the machine if anyone enters the

area.

•Do not mow in reverse unless absolutely

necessary. Always look down and behind before

and while backing.

•Slow down before turning. Sharp turns on any

terrain may cause loss of control.

•Turn off the blades when not mowing.

•Keep hands, feet, hair and loose clothing away

from attachment discharge area, underside of

mower and any moving parts while the engine is

running.

•Mow only in daylight or good artificial light.

•Watch for traffic when operating near or crossing

roadways.

•Do not touch equipment or attachment parts

which may be hot from operation. Allow to cool

before attempting to maintain, adjust or service.

•Before operating a machine with roll over

protection be certain the seat belts are attached

and seat is latched to prevent the seat from

pivoting forward.

•Use only Toro-approved attachments. Warranty

may be voided if used with unapproved

attachments.

Slope Operation

Slopes and ramps are a major factor related to loss-of-

control and tip-over accidents, which can result in

severe injury or death. All slopes and ramps require

extra caution. If you cannot back up the slope or if

you feel uneasy on it, do not mow it.

•If you must ascend a steep slope, back up the hill,

and drive forward down the hill, keeping the

machine in gear.

•Remove obstacles such as rocks, tree limbs, etc.

from the mowing area. Watch for holes, ruts or

bumps, as uneven terrain could overturn the

machine. Tall grass can hide obstacles.

•Use slow speed so that you will not have to stop

while on the slope.

•Follow the manufacturer’s recommendations for

wheel weights or counterweights to improve

stability.

•Use extra care with other attachments. These can

change the stability of the machine.

•Keep all movement on slopes slow and gradual.

Do not make sudden changes in speed or

direction.

•Avoid starting or stopping on a slope. If the tires

lose traction, disengage the blades and proceed

slowly straight down the slope. Avoid raising the

side decks on a slope.

•When operating the machine on slopes, banks or

near drop offs, always have roll-over protection

installed.

•When operating a machine with roll-over

protection always use seat belt.

•Be certain that the seat belt can be released

quickly if the machine is driven or rolls into

ponds or water.

•Check carefully for overhead clearances (i.e.,

branches, doorways, electrical wires) before

driving under any objects and do not contact

them.

DO NOT

•Do not mow slopes exceeding 15 degrees.

•Avoid turning on slopes. If you must turn, turn

slowly and gradually downhill, if possible.

•Do not mow near drop-offs, ditches, or

embankments. The machine could suddenly turn

over if a wheel goes over the edge of a cliff or

ditch, or if an edge caves in.

•Do not mow on wet grass. Reduced traction

could cause sliding.

•Do not try to stabilize the machine by putting

your foot on the ground.

Service

•Never store the machine or fuel container inside

where there is an open flame, such as near a

water heater or furnace.

•Keep nuts and bolts tight, especially the blade

attachment bolts. Keep equipment in good

condition.

•Never tamper with safety devices. Check safety

systems for proper operation before each use.

•Use only genuine replacement parts to ensure

that original standards are maintained.

•Check brake operation frequently. Adjust and

service as required.

•Battery acid is poisonous and can cause burns.

Avoid contact with skin, eyes and clothing.

Protect your face, eyes and clothing when

working with a battery.

•Battery gases can explode. Keep cigarettes,

sparks and flames away from the battery.

•Hydraulic fluid escaping under pressure can

penetrate the skin and cause injury. Use

cardboard or paper to find hydraulic leaks. Never

use your hands.

Sound Pressure Level

This unit has an equivalent continuous A-weighted

sound pressure at the operator ear of: 90 dB(A), based

on measurements of identical machines per Directive

84/538/EEC and amendments.

Sound Power Level

This unit has a sound power level of: 105 dB(A) 1

pW, based on measurements of identical machines per

Directive 84/538/EEC and amendments.

Vibration Level

Hand-Arm

This unit does not exceed a vibration level of 2.5 m/s2

at the hands based on measurements of identical

machines per ISO 5349 procedures.

Whole Body

This unit does not exceed a vibration level of 0.5

m/s2at the posterior based on measurements of

identical machines per ISO 2631 procedures.

93-7830

1. Danger—See operator’s manual

2. Wheel torque specifications

93-7841

1. Danger—See operator’s manual

100-6577

1. Lock—Unlock the deck service lock

93-6680

1. Diesel fuel

93-7272

1. Fan blades can cause injury

2. Stay away from moving parts

93-7822

1. Danger

2. See Operator’s manual

3. Fill the fuel tank to 1” from bottom of the filler neck

105-2512

1. Read operator’s manual for starting instructions

2. Danger—Read operator’s manual

3. Tipping hazard—Go slow and avoid sharp turns on

slopes to avoid rollover. The deck must be lowered when

going down slopes for steering control. Always wear seat

belts with roll-over protection.

4. Thrown object hazard—keep bystanders away

5Cutting hazard to hands or feet—stay away from rotating

blades or moving parts.

6. Danger—set the parking brake, stop the engine and

remove the key before leaving the operator’s position.

100-6574

1. Hot surface stay away

2. Stay away from moving parts

Safety and Instruction Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential

danger. Replace any decal that is damaged or lost.

93-7276

1. Explosion hazard—wear eye protection.

2. Caustic liquid hazard—flush with water and seek first aid.

3. Fire hazard — no sparks, flame, or smoking

4. Poison—keep children a safe distance from the battery.

93-7840

1. Coolant level

2. Hot surface—keep a safe distance

3. Danger—rear the operator’s manual

4. Explosion hazard—stay away

93-6668

1. The battery contains lead. Do not throw it in the garbage.

100-6581

1. To lock parking brake—Latch pedals together, apply

brake pedals and pull up on knob

2. To unlock parking brake—step on brake pedals

100-6552

1. Refer to Operator’s Manual for engine oil specifications

93-7834

1. No step

2. Traction pedal

3. Traction—forward

4. Traction—reverse

5. Danger—Shut off power take-off prior to raising decks

6. Danger—Do not operate decks when they are in raised

position

93-7833

1. Throttle control

2. Throttle—fast

3. Throttle—slow

4. Tipping hazard—Lower the deck when going down slopes

greater than 10 degrees

5. Tipping hazard—Lower the deck when going down slopes

greater than 10 degrees

6. Danger—tipping hazard

7. Lift lever—raise position

8. Lift lever—lower position

9. Lift lever—float position

Andere Handbücher für 30241 Groundsmaster 228-D

Inhaltsverzeichnis

Andere Toro Rasenmäher Handbücher

Toro

Toro Super Recycler 20053 Bedienungsanleitung

Toro

Toro TimeCutter HD XS4850 Bedienungsanleitung

Toro

Toro Recycler II ProLine 21 Bedienungsanleitung

Toro

Toro GROUNDSMASTER 345 Bedienungsanleitung

Toro

Toro Groundsmaster 4700-D Bedienungsanleitung

Toro

Toro Z Master Professional 7500-DSeries Handbuch

Toro

Toro Groundsmaster 3400 Montage- und Bedienungsanleitung

Toro

Toro TimeCutter HD MyRide 48in Bedienungsanleitung

Toro

Toro 22188 Bedienungsanleitung

Toro

Toro 412690000 Bedienungsanleitung

Toro

Toro Greensmaster TriFlex 3400 Bedienungsanleitung

Toro

Toro Z580-D Z Master 74266CP Bedienungsanleitung

Toro

Toro TurfMaster 22205TE Bedienungsanleitung

Toro

Toro Z-Master Z149 Bedienungsanleitung

Toro

Toro 29732 Bedienungsanleitung

Toro

Toro 78281 Bedienungsanleitung

Toro

Toro TimeCutter SS 5060 Bedienungsanleitung

Toro

Toro 71212 Handbuch

Toro

Toro 20052 Bedienungsanleitung

Toro

Toro 29639 Bedienungsanleitung

Toro

Toro Recycler 20367 Bedienungsanleitung

Toro

Toro TimeMaster 21199 Bedienungsanleitung

Toro

Toro TimeCutter MX 5075 Bedienungsanleitung

Toro

Toro ProLine 22038 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 050 thru 062 Bedienungsanleitung