Toro 73551 Handbuch

The Toro Company – 1997

FORM NO. 3319–230 A

SET UP

INSTRUCTIONS

MODEL NO. 73551–8900001 & UP

523Dxi GARDEN TRACTOR

Loose Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Rear Wheel

Wheel Bolt

10 Installing the rear wheels

R.H. Wheel Spindle

L.H. Wheel Spindle

Unplated Thrust Washer – 1.56” O.D x .06”

Thick

Plated Wheel Washer –1.50” O.D x .05” Thick

Bolt – 5/16”-18 x 2.25” Long

Hex Nut – 5/16”-18

Spindle Cap

Front Wheel

Hubcap Washer – 2.50” O.D x .05” Thick

Cotter Pin –.156” x 1.50” Long

Shim Washer – 1.50” O.D x .015” Thick

Hubcap

Installing the front wheels

Steering Wheel

Boot Washer

Nut

Lock Washer

Trim Cover

Installing the steering wheel

Seat Assembly

Shoulder Bolt – 5/16”

Locknut – 5/16”

2Installing the seat

Set-Up Instructions

DESCRIPTION USEQTY.

Bolt – 1/4”-20 x .75” Long

Wing Nut – 1/4”-20

2Attaching the battery cables

Grill Screw – #8 x .50” Long

Grill Washer – .75” O.D.

2Securing the grill

Hitch Pin

Hairpin Cotter

Flat Washer – .50” I.D.

2Installing the drawbar hitch pin

Key 1Use in ignition switch

Operator’s Manual 1Read before operating the tractor

Engine Operator’s Manual 1Read before operating the tractor

Installing the Rear Wheels

1. Remove the four wheel bolts holding the rear

shipping brackets to the rear hubs.

2. Using a jack or suitable hoist, raise the rear of

the tractor only high enough to install the rear

wheels.

3. Install the wheels onto the hubs with the valve

stems facing inward (Fig. 1).

4. Tighten the wheel bolts to 75–80 ft-lb

(105–112 Nm).

m–1278

Figure 1

1. Hub

2. Rear wheel 3. Wheel bolt (5)

Installing the Front Wheels

IMPORTANT: Never raise the front of the

tractor by placing a jack under the bumper

or front axle because the tractor may be

damaged.

1. The front hood support braces have two slots

(Fig. 2) that may be used to lift the tractor to

install the front wheel spindles. To access these

slots, remove the front grill and raise the hood.

m–3454

2 2

Figure 2

1. Slots 2. Grill Grommets

Note: Remove, or be careful not to damage,

the two upper grill grommets (Fig. 2).

Set-Up Instructions

2. Using a suitable hoist, raise the front of the

tractor only high enough to install the front

wheel spindles.

IMPORTANT: Do not pivot the weight of the

tractor onto the rear drawbar hitch because

the hitch will be damaged.

3. Install a 1.56” O.D. x .06” thick unplated thrust

washer onto the splined shaft of the R.H. wheel

spindle (Fig. 4).

4. Install the splined end of the R.H. spindle

through the R.H. end of the front axle and into

the steering arm (Fig. 4).

Note: The L.H. and R.H. spindles are

different. Assemble the spindles as

shown in figure 3.

Note: The outside edge of the spindle must

be parallel to the end of the steering

arm (Fig. 3).

m–3610

Figure 3

1. R.H. Spindle

2. L.H. Spindle 3. Steering arm

4. Parallel relationship

5. Secure the spindle shaft to the steering arm with

a 5/16”–18 x 2.25” bolt and 5/16” nut (Fig. 4).

Torque the nut to 230 25 in–lbs.

6. Insert a 1.50” O.D x .05” thick plated wheel

washer onto the R.H. spindle (Fig. 4).

7. Install a front wheel onto the R.H. spindle with

the valve stem facing inward (Fig 4).

8. Insert another 1.50” O.D x .05” thick plated

wheel washer onto the R.H. spindle (Fig. 4).

9. Install a 2.50” O.D x .05” thick hub cap washer

onto the spindle. Now insert a .156 x 1.50” long

cotter pin into the hole in the spindle (Fig. 4).

10. Check the front wheel end play. Install shim

washers inside the hubcap washer as necessary

so there is minimum end play.

m–3452

910

Figure 4

1. Wheelspindle

2. Unplated thrust washer

1.56” x .06” thick

3. Front axle

4. Steering arm

5. Bolt 5/16”–18 x 2.25”

6. Nut 5/16”

7. Spindle cap

8. Plated wheel washer 1.50”

O.D. x .05” thick

9. Hub cap washer 2.50”

O.D. x .05” thick

10. Shim washer 1.50” O.D. x

.015” thick

11. Cotter pin .056” x 1.50”

12. Hubcap

11. Secure the wheel to the spindle with a cotter pin.

Bend the ends of the cotter pin completely

around the spindle.

12. Install a hubcap onto the hubcap washer until it

snaps in place (Fig. 4).

Set-Up Instructions

13. Look at the end of the steering arm and the

inside edge of the tire. The end of the steering

arm and the inside edge of the tire must be

parallel (Fig. 5). Adjust the steering arm if

required.

m–3451

Figure 5

1. Wheel

2. Steeringarm 3. Parallel relationship

14. Insert a spindle cap into the steering arm

(Fig. 4).

15. Repeat the procedure on the opposite end of the

front axle.

16. After servicing the battery, replace the front grill

of the tractor and secure the grill with two #8 x

.50” long grill screws and .75” O.D. grill

washers in the upper two grill mounting holes

(Fig. 6).

m–3558

Figure 6

1. Grill screw (1 of 2) 2. Grill washer (1 of 2)

17. Lubricate the spindles and front axle pivot until

grease begins to come out of the bearings.

18. With the tractor on a level surface, check to

make sure the front wheel toe-in is between 1/8”

and 1/4”. For instructions on adjusting toe-in,

refer to the Maintenance section in Operator’s

Manual.

Checking Tire Pressure

Check front and rear tire pressure. The correct front

and rear tire pressure is 12 psi (82.7 kPa).

Set-Up Instructions

Installing the Seat

1. Mount the seat to the seat base using two 5/16”

shoulder bolts and lock nuts (Fig. 7).

2. Insert the seat switch wire through the center

opening in the seat base (Fig 7).

3. Push the seat switch wire connector into the wire

harness connector.

m–3453

Figure 7

1. Seat

2. Seat base

3. 5/16” shoulder bolt (2)

4. 5/16” Locknut (4)

5. Seat switch wire

connector

6. Opening for seat switch

wire

Installing the Steering Wheel

1. Install the boot washer onto the steering shaft

(Fig. 8).

2. Remove the plastic trim cover from the steering

wheel (Fig. 8)

3. Install the steering wheel onto the shaft,

carefully aligning the splines (Fig. 8).

Note: There is no fixed straight ahead

position on power steering models.

4. Secure the steering wheel to the shaft with a lock

washer and nut (Fig. 8). Tighten the retaining nut

to 45–50 ft–lbs.

5. Install the trim cover on the steering wheel.

m–2482

Figure 8

1. Boot washer

2. Steering shaft

3. Steering wheel

4. Lock washer

5. Nut

6. Trim cover

Set-Up Instructions

Activating the Battery

POTENTIAL HAZARD

•Battery electrolyte contains sulfuric acid

which is a deadly poison and it causes

severe burns.

WHAT CAN HAPPEN

•If you carelessly drink electrolyte you could

die or if it gets onto your skin you will be

burned.

HOW TO AVOID THE HAZARD

•Do not drink electrolyte and avoid contact

with skin, eyes or clothing. Wear safety

glasses to shield your eyes and rubber

gloves to protect your hands.

•Fill the battery where clean water is always

available for flushing the skin.

•Follow all instructions and comply with all

safety messages on the electrolyte container.

1. Remove the battery from the tractor (refer to

Removing the Battery in your tractor Operator’s

Manual).

Note: Never fill the battery electrolyte with

the battery installed in the tractor.

2. Remove the cell cover from the battery. Slowly

pour electrolyte into each cell until the

electrolyte level is up to the lower part of the

tube (Fig. 9). Use an electrolyte with a specific

gravity of 1.265.

m–3799

Figure 9

1. Cell cover

2. Electrolyte 3. Lower part of tube

POTENTIAL HAZARD

•Charging battery produces gasses.

WHAT CAN HAPPEN

•Battery gasses can explode.

HOW TO AVOID THE HAZARD

•Keep cigarettes, sparks and flames away

from battery.

3. Leave the cell cover off and connect a 3–4 amp

battery charger to the battery posts (Fig. 10).

Charge the battery at a rate of 4 amperes or less

for 4 hours (12 volts).

Set-Up Instructions

4. When the battery is fully charged, unplug the

charger from electrical outlet, then disconnect

the charger leads from the battery posts

(Fig. 10).

m–3798

Figure 10

1. Positive battery post

2. Negative battery post 3. Red (+) charger lead

4. Black (–) charger lead

5. Slowly pour electrolyte into each cell until the

level is once again up to the lower part of the

tube (Fig. 9), then install the cell cover.

6. Install the battery in the tractor and connect the

battery cables (refer to Installing the Battery in

your tractor Operator’s Manual).

Note: Do not run the tractor with the battery

disconnected.

Installing the Drawbar Hitch

Insert the drawbar hitch pin into the drawbar hitch

and secure it with a .50” I.D. flat washer and hairpin

cotter (Fig. 11).

m–2481

Figure 11

1. Drawbarhitch pin

2. Drawbar hitch 3. .50” Flat washer

4. Hairpin cotter

Set-Up Instructions

Checking the Wiring and

Fasteners

•Inspect the tractor for any loose electrical

connections and secure them as required. Check

the wire routing to make sure moving parts do

not interfere with wires and cause a short.

•Assure all fasteners are tight.

Burnishing the Clutch

The following break–in procedure must be performed

as part of predelivery service or when a new clutch is

installed.

Note: There must be a PTO driven

attachment installed to provide a load

in order to burnish the clutch facings

properly.

1. Run the engine at full throttle and engage the

clutch bringing the load to full speed. Then

disengage the clutch.

2. Let the load come to a full stop, then engage

again.

3. Repeat these procedures (1 and 2) 5 times.

Test Driving the Tractor

1. Check the oil level in the crankcase (refer to

Engine Oil in your tractor Operator’s Manual for

oil type, viscosity and crankcase capacity).

2. Check the oil level in the transaxle (refer to

Transaxle Fluid in your tractor Operator’s

Manual for oil type, viscosity and capacity).

3. Check that the coolant level is between the two

lines on the coolant recovery tank when the

engine is cold (refer to Check the Cooling

System in your tractor Operator’s Manual).

4. Make sure all water is drained from the fuel filter

(refer to Draining Water From The Fuel

Filter/Water Separator in your tractor Operator’s

Manual).

5. Check to make sure all lubrication points have

been greased as shown in the Maintenance

section of tractor Operator’s Manual.

6. Fill the tank with fresh diesel fuel with a

minimum cetane rating of 40 and the proper

grade for the ambient temperature conditions

(refer to Adding Fuel in your tractor Operator’s

Manual) Open the fuel shutoff valve and check

the fuel hose and fittings for leaks.

7. As applicable, check and test the operation of the

following:

•Engine and throttle controls

•Gauges

•Headlights and taillights

•Indicator lights

•PTO clutch and brake

•Lift system

•Service and parking brakes

•Transmission controls

•Steering

•Tractor operation in forward and reverse

8. Test the operation of the safety interlock system

(refer to the tractor Operator’s Manual for the

correct procedure).

Andere Handbücher für 73551

Inhaltsverzeichnis

Andere Toro Rasenmäher Handbücher

Toro

Toro 30555 Bedienungsanleitung

Toro

Toro 74657 Bedienungsanleitung

Toro

Toro 30070 Bedienungsanleitung

Toro

Toro 74991 Z Master Professional 5000 Series Bedienungsanleitung

Toro

Toro Groundsmaster 4500-D Bedienungsanleitung

Toro

Toro Super Recycler 20044 Bedienungsanleitung

Toro

Toro TimeCutter SW 4200 Bedienungsanleitung

Toro

Toro 29645 Bedienungsanleitung

Toro

Toro Super Recycler 20054 Bedienungsanleitung

Toro

Toro TITAN HD 1500 Bedienungsanleitung

Toro

Toro 73542 Bedienungsanleitung

Toro

Toro Groundsmaster 5900 Series Bedienungsanleitung

Toro

Toro 75750TA Bedienungsanleitung

Toro

Toro Recycler 20073 Bedienungsanleitung

Toro

Toro 74410 Bedienungsanleitung

Toro

Toro reelmaster 5410 series Bedienungsanleitung

Toro

Toro 03691 Bedienungsanleitung

Toro

Toro 04054 Greensmaster 800 Bedienungsanleitung

Toro

Toro LX465 Bedienungsanleitung

Toro

Toro 74805 Bedienungsanleitung

Toro

Toro REELMASTER 6500 D Bedienungsanleitung

Toro

Toro 3431 Bedienungsanleitung

Toro

Toro 140-2050 Bedienungsanleitung

Toro

Toro 31201 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

Craftsman

Craftsman 917.378461 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung