Toro 78395 Bedienungsanleitung

Operator’s Manual

Domestic English (EN)

Form No. 3326-584

60Mower

Wheel Horse5xi Garden Tractor Attachment

Model No. 78395—Serial No. 220000001 and Up

Printed in the USA

2001 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Contents

Page

Introduction 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety and Instruction Decals 3. . . . . . . . . . . . . . . . . . .

Setup 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Loose Parts 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Assembling the Mower 4. . . . . . . . . . . . . . . . . . . . .

Installing the Mower 5. . . . . . . . . . . . . . . . . . . . . .

Attaching the PTO Drive Belt 8. . . . . . . . . . . . . . .

Adjusting the Mower 9. . . . . . . . . . . . . . . . . . . . . .

Removing the Mower 11. . . . . . . . . . . . . . . . . . . . . .

Operation 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating the Mower 14. . . . . . . . . . . . . . . . . . . . . .

Adjusting the Front Wheels 14. . . . . . . . . . . . . . . . .

Checking for Debris 14. . . . . . . . . . . . . . . . . . . . . . .

Tips for Mowing Grass 14. . . . . . . . . . . . . . . . . . . . .

Maintenance 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Recommended Maintenance Schedule 15. . . . . . . . .

Servicing the Blades 16. . . . . . . . . . . . . . . . . . . . . . .

Greasing the Mower 17. . . . . . . . . . . . . . . . . . . . . . .

Checking PTO Drive Belt Tension 18. . . . . . . . . . . .

Extending PTO Drive Belt Life 18. . . . . . . . . . . . . .

Replacing the Blade Drive Belt 19. . . . . . . . . . . . . .

Storage 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Introduction

Read this manual carefully to learn how to operate and

maintain your product properly. The information in this

manual can help you and others avoid injury and product

damage. Although Toro designs and produces safe

products, you are responsible for operating the product

properly and safely.

Whenever you need service, genuine Toro parts, or

additional information, contact an Authorized Service

Dealer or Toro Customer Service and have the model and

serial numbers of your product ready. Figure 1 illustrates

the location of the model and serial numbers on the

product.

1m–3569

Figure 1

1. Location of the model and serial numbers

Write the product model and serial numbers in the space

below:

Model No.

Serial No.

This manual identifies potential hazards and has special

safety messages that help you and others avoid personal

injury and even death. Danger, Warning, and Caution are

signal words used to identify the level of hazard. However,

regardless of the hazard, be extremely careful.

Danger signals an extreme hazard that will cause serious

injury or death if you do not follow the recommended

precautions.

Warning signals a hazard that may cause serious injury or

death if you do not follow the recommended precautions.

Caution signals a hazard that may cause minor or moderate

injury if you do not follow the recommended precautions.

This manual uses two other words to highlight information.

Important calls attention to special mechanical

information and Note: emphasizes general information

worthy of special attention.

Safety and Instruction Decals

This machine meets or exceeds the B71.1-1998 specifications of the American National Standards Institute, in effect at

the time of production. However, improper use or maintenance by the operator or owner can result in injury. To

reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert

symbol, which means CAUTION, WARNING, or DANGER—“personal safety instruction.” Failure to comply with

the instruction may result in personal injury or death. Refer to your tractor Operator’s Manual for additional safety

instructions.

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger. Replace any decal that is damaged or lost.

93-1122

98-3480

111655

92-7108

98-3478

98-3481

93-7282

1. Stop the engine and

remove the key before

leaving the tractor

2. Read the Operator’s

Manual

3. Wheel height

Setup

Note: Determine the left and right sides of the machine from the normal operating position.

Loose Parts

Note: Use the chart below to identify parts used for assembly.

Description Qty. Use

Discharge chute

Spring

Bolt, 3/8 x 3-1/2 in.

Locknut, 3/8 in.

Install discharge chute

Pulley box

PTO drive belt 1

1Install the PTO drive belt

Assembling the Mower

Installing the Discharge Chute

1. Place the springs into the brackets on the mower with

the hooked ends over the raised back of the bracket

(Fig. 2).

m–3484

Figure 2

1. Bracket

2. Spring hook end

3. Space for spring

4. Discharge chute

5. Bolt

6. Locknut

2. Align the discharge chute with the holes in the brackets

and the spring straight ends in the space under the hinge

and above the chute (Fig. 2).

3. Secure the chute to the bracket with bolts through the

discharge chute, springs, and brackets. Secure them

with locknuts (Fig. 2).

4. Lift the discharge chute and check that it is spring

loaded and snaps freely to the full down position.

Important The discharge chute must be spring loaded

in the down position.

Danger

Without the grass deflector mounted in place, you

and others are exposed to blade contact and

thrown debris. Contact with the rotating mower

blades and thrown debris will cause injury or

death.

•Never remove the grass deflector from the

mower because the grass deflector routes

material down toward the turf. If the grass

deflector is ever damaged, replace it

immediately.

•Never put your hands or feet under the mower.

•Never try to clear the discharge area or mower

blades unless you move the power take off

(PTO) to Off and rotate the ignition key to Off.

Also remove the key and pull the wires off of the

spark plugs.

Mower Belt Routing

Route the mower belt as shown in Fig. 3. Ensure that you

install the belt on the lower mower deck pulley.

m–3573

Figure 3

Top View

1. Mower belt 2. Mower deck pulley

Installing the Mower

Preparing the Mower

Install the mower on a level concrete surface. Rough dirt

or lawn surfaces make installation much more difficult.

1. Place the height of cut lever on the mower to the

position for lowest cut (Fig. 4).

m–3591

Figure 4

1. Height of cut lever

position

2. Front mower wheels

parallel to mower

3. Clevis pin

4. Hairpin cotter

2. Lower the rear center wheel (if not already lowered),

using the following procedure:

A. Remove the hairpin cotter from the wheel rod

(Fig. 5).

m–3579

Figure 5

1. Hairpin cotter

2. Wheel rod 3. Hole in height–of–cut

plate

4. Rear center wheel

B. Lift the rear of the mower.

C. Pull the rod toward the outside of the mower, insert

the end of the rod into the hole in the height of cut

plate, and install the hairpin cotter into the second

hole of the wheel rod (Fig. 5).

3. Set the height of the two front mower wheels and turn

the wheels parallel to the mower by removing the clevis

pins and hairpin cotters, then turning and raising or

lowering the wheels until you can put the clevis pins

and hairpin cotters in the third position from the top

(Fig. 4).

Preparing the Tractor

Install the mower on a level concrete surface. Rougher dirt

or lawn surfaces make installation more difficult.

1. Position the tractor and mower side by side, with the

mower on the right side of the tractor.

2. Set the parking brake, raise the attachment lift, turn the

steering wheel all the way to the right, stop the

engine, and remove the ignition key.

3. If you have previously had a snowthrower, blade, or

tiller attached to the attachment lift, remove the two

clevis pins on each side of the attachment lift (Fig. 6).

m–3433

Figure 6

1. Clevis pin 2. Hairpin cotter

4. Attach the pulley box if it is not already on the tractor

(Fig. 7).

m–5510

Figure 7

1. Attach-A-Maticlatches

2. Pulley box

3. Idler pulley

4. Belt tension release arm

5. Belt tension adjustment

knob

6. Belt tension indicators

7. Attach-A-Maticbuttons

(one on each side)

A. Ensure that the latches on the tractor’s front

Attach-A-Maticare open.

B. Slide the pulley box into the Attach-A-Matic

latches and seat it.

C. Close the latches.

Attaching the Mower

1. From the right side of the tractor, slide the mower under

the tractor (Fig. 8).

Note: Once the mower is almost under the tractor, you may

need to turn the steering wheel to the left to provide enough

room for the mower to slide completely under the tractor.

m–3575

Figure 8

1. Front tractor wheels

2. Position the mower so that the slots in the side of each

of the mower mounting brackets (Fig. 9) are aligned

directly below the tractor attachment lift arm.

m–3574

Figure 9

1. Slots in the side mounting

brackets (2) 2. Front to rear adjustment

rod

3. Start the tractor.

4. Lower the attachment lift arm fully and adjust the

mower position until you can pull out on the J-pin of

the lift arm and slide it into the slot in the mounting

bracket of the mower (Fig. 10).

m–3456

Figure 10

Left Side of Tractor Shown

1. J-pin 2. Mower slot in side

mounting bracket.

5. On the left side, pull out the attachment lift J-pin and

slide it into the slot on the other mower mounting

bracket.

6. After the two J-pins are seated through the mower

mounting brackets, using the attachment lift and your

hand on the right front adjustable mower wheel bracket

(Fig. 11), position the mower so its attachment bar fits

into the mid Attach-A-Maticmount.

Movement of the attachment lift between the

mower mounting brackets and the attachment lift

arms can injure a person when aligning the mower

with the lift arms.

•Keep hands away from moving parts while

operating the attachment lift.

•Always position the mower with your hand on

the right front mower wheel bracket.

•Never try to position the mower with your

hands on the mower mounting brackets or

below the mower housing.

Caution

m–3575

Figure 11

7. Turn the lever of the Attach-A-Matic

counterclockwise to lock the mower to the tractor

(Fig. 12).

m–3611

Figure 12

1. Attach-A-Maticbutton

2. Attach-A-Maticlever 3. Lock

8. Raise the rear center wheel on the mower so that it will

not interfere with mowing, using the following

procedure:

Important Always raise the rear center wheel before

mowing. The mower may become damaged if the wheel is

left in the down position while mowing.

A. Remove the hairpin cotter from the wheel rod

(Fig. 13).

m–3582

Figure 13

1. Wheel rod

2. Hairpin cotter 3. Rear center wheel

4. Height–of–cut plate

B. Slide the wheel rod back toward the center wheel as

far as it will go. The end of the control rod should

no longer be in the hole in the height of cut plate

(Fig. 13).

C. Install the hairpin cotter into the wheel rod hole

closest to the height of cut plate (Fig. 13).

9. Turn the two front mower wheels parallel to the tractor.

A. If the mower has not been leveled with the tractor,

set the height of the front wheels to the highest

position from the ground.

B. If the mower has been leveled with the tractor, refer

to Adjusting the Two Front Wheels, page 14.

10.Set the parking brake, lower the attachment lift, stop the

engine, and remove the ignition key.

Attaching the PTO Drive Belt

1. Remove the tractor grill.

Components under the hood will be hot if the

tractor has been running. If you touch hot

components you may be burned.

Allow the tractor to cool before performing

maintenance or touching components under the

hood.

Caution

2. Release the belt tension release arm on the pulley box

housing and swing it out toward you (Fig. 14).

m–5511

Figure 14

1. Belt tension release arm

2. Belt tension indicators

3. Belt tension adjustment

knob

4. Seating position for

tension arm

5. Belt tension released

3. Hang the belt over the mower and extend the belt

through the center of the pulley box, between the two

pulleys.

4. Position the belt into the groove of the PTO pulley

(Fig. 15), making sure it is also under the pulleys in the

pulley box.

m–4231 1

Figure 15

1. Pulley box pulley

2. PTO pulley 3. PTO drive belt

5. Loop the other end of the belt over the drive pulley of

the mower. Additional belt slack can be obtained (if

needed) by turning the belt tension adjustment knob

(Fig. 14).

6. Make certain that the wide side of the PTO drive belt is

toward the outside diameter of all (four) pulleys

(Fig. 16).

m–4230

ÏÏÏÏ

Figure 16

1. Pulley outside diameter 2. Wide side of belt

7. Adjust the belt tension.

A. Push the belt tension release arm toward the pulley

box to tension the belt.

B. Check the tension indicators on front of the pulley

box. The two arrow points on the indicators should

line up (Fig. 14).

C. If the tension indicators do not line up, release the

belt tension, turn the adjustment knob and repeat

steps A through C until the indicators line up

(Fig. 14).

When finished, swing the tension release arm into

the pulley box and seat it by moving it into the

position shown in Figure 14.

8. Replace the front grill of the tractor.

Adjusting the Mower

Adjusting the Height of Cut

You can adjust the rear support wheels in different hole

locations for 1-1/2 to 4 in. (4 to 10 cm) heights of cut.

1. Start the tractor, set the parking brake, and raise the

mower. Get off the tractor.

2. Pull the height of cut lever out to disengage it from the

quadrant (Fig. 17).

m–3474

Figure 17

1. Height-of-cut lever

2. Quadrant 3. High

4. Low

3. Adjust the height-of-cut to the desired level (Fig. 17).

4. Release the lever inward to lock it into the quadrant

(Fig. 17).

5. Adjust the front wheels in the proper hole location for

the selected height-of-cut; refer to Adjusting the Two

Front Wheels, page 14.

Checking the Mower Level

For optimum efficiency, check the level of the mower after

installation and periodically, to ensure that the blades are

1/8 in. (3 mm) lower in the front than in the rear.

Check and adjust the mower on a flat, level surface,

preferably concrete. Before checking the mower level, set

the air pressure in the front and rear tires as specified in the

tractor Operator’s Manual. Place the mower height-of-cut

lever to the middle cut position. Ensure that the two

adjustable front wheels are off of the ground.

1. Disengage the PTO, set the parking brake, lower the

attachment lift, stop the engine, and remove the ignition

key.

2. Carefully rotate one of the blades so it is oriented front

to rear (Fig. 18).

m–3523

Front

Figure 18

1. Blade oriented front to

rear

2. Measure front blade tip

3. Rotate front tip to rear

and measure

4. Measure here (side to

side)

3. Measure the distance from the front tip of the blade

(Fig. 18) to the flat surface.

4. Carefully rotate the blade tip until it is in the rear

position and measure it in that position.

When the blade tip is in the front position, it should be

1/8 in. (3 mm) lower than when it is in the rear position.

5. If an adjustment is required, turn the adjusting nut

(Fig. 19) on the back of the mower.

•To raise the front of the mower, turn the adjustment

nut clockwise.

•To lower the front of the mower, turn the nut

counterclockwise.

m–3574

Figure 19

1. Front to rear adjustment rod

Adjusting the Side to Side Blade Cut

This optional adjustment is available if necessary to

compensate for uneven side to side cut.

Equalize the side to side cut by adjusting the two carriage

bolts (Fig. 20) on the mower wheels. Check the height of

the blade at outside blade tips (Fig. 18).

m–3577

Figure 20

1. Side to side adjustment bolts

Andere Handbücher für 78395

Inhaltsverzeichnis

Andere Toro Rasenmäher Handbücher

Toro

Toro 75742 Bedienungsanleitung

Toro

Toro eTimeMaster 21491 Bedienungsanleitung

Toro

Toro Recycler 20332 Bedienungsanleitung

Toro

Toro 30607A Bedienungsanleitung

Toro

Toro 20351-Serial Bedienungsanleitung

Toro

Toro GrandStand 74534 Bedienungsanleitung

Toro

Toro LX427 Bedienungsanleitung

Toro

Toro Super Recycler 20794 Bedienungsanleitung

Toro

Toro TimeCutter 74701 Bedienungsanleitung

Toro

Toro 75967 Bedienungsanleitung

Toro

Toro 02000 GROUNDS PRO 2000 Bedienungsanleitung

Toro

Toro 39494 Bedienungsanleitung

Toro

Toro Groundsmaster 4500-D Bedienungsanleitung

Toro

Toro 21773 Bedienungsanleitung

Toro

Toro 71198 Bedienungsanleitung

Toro

Toro 71427 Bedienungsanleitung

Toro

Toro TITAN HD 1500 Bedienungsanleitung

Toro

Toro Recycler 20010 Bedienungsanleitung

Toro

Toro TimeCutter ZS 4200S Bedienungsanleitung

Toro

Toro 3675 Bedienungsanleitung

Toro

Toro Recycler 20998 Bedienungsanleitung

Toro

Toro Titan 136-1654 Bedienungsanleitung

Toro

Toro 72211 Bedienungsanleitung

Toro

Toro Super Bagger 20897 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 050 thru 062 Bedienungsanleitung