Toro TimeCutter ZX Handbuch

W2004 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Original Instructions (EN)

TimeCutter)ZX Riding Mowers

Form No. 3353-782 Rev A

Setup Instructions

Loose Parts

Note: Use the chart below to verify that all parts have been shipped.

Description Qty. Use

Bolt, 1/4 x 3/4 inch

Washer, 1/4 inch

Nut, 1/4 inch

Installing the battery

Seat

Spacer

Knob

Flat washer, 5/16 inch

Installing the seat

Left-hand control lever

Right-hand control lever

Bolt, 3/8 x 1 inch

Curved washer, 3/8 inch

Installing the motion control levers

Hose coupling 1Washing the underside of the mower

Key 1

Operator’s Manual

Engine Operator’s Manual

1Read before operating the machine.

Registration card 1Fill out and return to Toro.

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related accessories

contain lead and lead compounds, chemicals

known to the State of California to cause cancer

and reproductive harm. Wash hands after

handling.

Warning

Installing the Battery

Bulk electrolyte with 1.260 specific gravity must be

purchased from a local battery supply outlet.

Danger

Battery electrolyte contains sulfuric acid which is a

deadly poison and causes severe burns.

•Do not drink electrolyte and avoid contact with

skin, eyes or clothing. Wear safety glasses to

shield your eyes and rubber gloves to protect

your hands.

•Fill the battery where clean water is always

available for flushing the skin.

•Follow all instructions and comply with all

safety messages on the electrolyte container.

1. Remove the battery from the machine and place it on a

level surface; refer to the Operator’s Manual,

Removing the Battery.

Important Never fill the battery with electrolyte while

the battery is installed in the tractor. Electrolyte could be

spilled on other parts and cause corrosion.

2. Clean the top of the battery with a paper towel.

3. Remove the vent caps from the battery (Fig. 1). Slowly

pour electrolyte into each battery cell until the

electrolyte level is up to the Upper line on the battery

case (Fig. 1).

Important Do not overfill the battery because

electrolyte (sulfuric acid) can cause severe corrosion and

damage to the chassis.

m-5004

Figure 1

1. Vent caps

2. Upper line

3. Lower line

4. Wait five to ten minutes after filling the battery cells.

Add electrolyte, if necessary, until the electrolyte level

is up to the Upper line (Fig. 1) on the battery case.

5. Install the battery vent caps.

6. Charge the battery for 1 hour at 25 to 30 amps or

6 hours at 4 to 6 amps (Fig. 2). Do not overcharge the

battery.

Charging the battery produces gasses that can

explode.

Never smoke near the battery and keep sparks and

flames away from battery.

Warning

7. When the battery is fully charged, unplug the charger

from the electrical outlet, then disconnect the charger

leads from the battery posts (Fig. 2).

8. Install the battery in the tractor and connect the battery

cables; refer to the Operator’s Manual, Installing the

Battery.

Figure 2

1. Positive post

2. Negative post

3. Charger red (+) wire

4. Charger black (–) wire

Installing the Motion Control

Levers

1. Remove the 4 bolts (3/8 x 1 inch) and 4 curved washers

(3/8 inch) which attach the motion control levers to the

control arm shafts for shipping (Fig. 3).

2. Place the levers (with the mounting plates toward the

rear of the machine) on the outside of the control arm

shaft and loosely secure them with the 4 bolts and

curved washers removed in step 1 (Fig. 3).

m–5215

Figure 3

1. Control arm

2. Bolt, 3/8 x 1 inch

3. Curved washer, 3/8 inch

4. Control arm shaft

3. Position the levers so that the bolts are in the center of

the slots on the lever mounting plate and tighten the

bolts until they are snug.

4. Align the front/rear position of the levers with each

other while in the neutral position. Loosen the bolts and

adjust the levers by sliding and/or tilting the lever(s)

forward or backward until they are properly aligned.

5. If the ends of the motion control levers hit against each

other while they are in the drive position (Fig. 4) (the

levers are rotated in as far as possible), make

adjustments by moving the levers outward to the neutral

lock position and carefully bend them outward. Move

them back to the drive position and check for clearance.

Repeat if necessary.

FRONT

UNIT

LEVERS IN

ALIGNMENT

Figure 4

Installing the Seat

1. Cut the plastic ties securing the seat to the machine for

shipping. Remove the seat.

2. Remove the knobs and flat washers (5/16 inch) from the

seat support.

3. Remove the spacers between the seat and seat support.

4. Raise the seat support on the machine (Fig. 5).

5. Slide the shoulder bolts on the bottom of the seat into

the slots on the seat support (Fig. 5).

6. Secure the seat to the seat support with the spacers, flat

washers and knobs removed in step 2 and 3 (Fig. 5).

m–5579

Figure 5

1. Seat support

2. Shoulder bolt

3. Knob

Important Make sure the spacers are between the seat

and support, and the knobs pass through the washers, seat

support, spacers and into the seat (Fig. 6).

m–7546

Figure 6

1. Seat

2. Seat support

3. Knob

4. Washer

5. Spacer

7. Lower the seat and adjust it if necessary; refer to

Positioning the Seat in the Operator’s Manual.

Washing the Underside of the

Mower

A hose coupling is included in loose parts for washing the

underside of the mower. See the Operator’s Manual for the

proper procedure.

Checking the Mower

Adjustment

The mower deck was leveled at the factory. If the mower is

not cutting level, adjust the side-to-side level and the

front-to-rear blade slope. See the Operator’s Manual for the

proper procedure.

Checking the Engine Oil Level

Before you start the engine and use the machine, check the

oil level in the engine crankcase; refer to Checking the Oil

Level in the Operator’s Manual.

Checking the Tire Pressure

Check the front and rear tires for proper inflation. Refer to

Tire Pressure in the Operator’s Manual for the

recommended inflation pressure.

Andere Toro Rasenmäher Handbücher

Toro

Toro Flex-Force Power System 21356 Bedienungsanleitung

Toro

Toro Recycler 20960 Bedienungsanleitung

Toro

Toro 74352 Bedienungsanleitung

Toro

Toro 400XT Series Bedienungsanleitung

Toro

Toro 30250TE Bedienungsanleitung

Toro

Toro 74228 Bedienungsanleitung

Toro

Toro TimeCutter HD MyRide 75212 Bedienungsanleitung

Toro

Toro Groundsmaster 1000L Bedienungsanleitung

Toro

Toro GrandStand 74568TE Bedienungsanleitung

Toro

Toro Super Recycler Bedienungsanleitung

Toro

Toro Recycler 20651 Bedienungsanleitung

Toro

Toro HoverPro 400 Bedienungsanleitung

Toro

Toro Greensmaster TriFlex 3300 Series Bedienungsanleitung

Toro

Toro 20835 Bedienungsanleitung

Toro

Toro 20955 Bedienungsanleitung

Toro

Toro 29639 Bedienungsanleitung

Toro

Toro 74200 Bedienungsanleitung

Toro

Toro 4042 Bedienungsanleitung

Toro

Toro 30839 Bedienungsanleitung

Toro

Toro 74504TE Bedienungsanleitung

Toro

Toro GrandStand 18850TE Bedienungsanleitung

Toro

Toro Recycler 20652 Bedienungsanleitung

Toro

Toro Z334 Z Master Handbuch

Toro

Toro 31971 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 050 thru 062 Bedienungsanleitung