Toro Z597 Z Master Handbuch

Form No. 3356-227 Rev A

Z597 Z Master® Diesel Mowers

Model No. For Z597 Diesel Mowers

Setup Instructions

Loose PartsUse the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Remove parts from the crate.

No parts required

–

Check the tire pressure.

Rear wheels

Install the drive wheels.

Roll bar, right section

Roll bar, left section

Roll bar, center section

Bolt (3/8 x 1 inch)

Curved washer

Flange nut (3/8 inch)

Bolt (1/2 x 3–1/4 inch)

Flange nut (1/2 inch)

Install the Rollover ProtectionSystem (ROPS).

No parts required

–

Adding diesel to the machine.

No parts required

–

Charge the battery.

Number 2 general purpose lithiumbase or molybdenum base grease.(Purchase separately.)

1 tube Check the machine for grease.

No parts required

–

Check the engine oil level.

No parts required

–

Prepare the side discharge chute.

No parts required

–

Check the machine before deliveryto the customer.

Operator’s Manual

Parts Catalog

Engine Owner’s Manual

Registration Card

Safety Video

111

Key 2

Delivering the machine to thecustomer.

Step

Removing Parts from theCrate

No Parts Required

Procedure

R emo v e the tires and the par ts for the R OPS from

the shipping crate .

Step

Checking the Tire Pressure

No Parts Required

Procedure

Pressure: 13 psi (90 kP a)

Note: T he front caster wheel is a semi-pneumatic

tire and does not need to be c hec k ed.

Chec k the air pressure in the dri v e tires .

Figure 1

Step

Raising the Machine Up andInstalling the Drive Wheels

Parts needed for this step:

Rear wheels

Procedure

1. R emo v e the screws holding the right angle

retaining plate to the crate .

Figure 2

2. Raise the bac k of the mac hine up and suppor t

it with jac k-stands .

Figure 3

3. R emo v e the wheel n uts from both sides of the

v ehicle and remo v e the right angle retaining

plate . Discard the screws and retaining plate .

Figure 4

4. Mount the wheels with the v alv e stem to the

outside and secure them with the wheel n uts

previously remo v ed.

5. T or que the wheel n uts to 95 ft-lb (128 N·m).

6. R emo v e the jac k-stands .

Figure 5

Step

Installing the Roll OverProtection System

Parts needed for this step:

Roll bar, right section

Roll bar, left section

Roll bar, center section

Bolt (3/8 x 1 inch)

Curved washer

Flange nut (3/8 inch)

Bolt (1/2 x 3–1/4 inch)

Flange nut (1/2 inch)

Procedure

1. Loosely install the right and left roll bar section

to the frame , with 8 bolts (3/8 x 1 inc h), 8

cur v ed w ashers , and 8 ﬂang e n uts (3/8 inc h).

Note: T he cur v e w asher cone m ust be

installed to w ard the bolt head.

Figure 6

2. Install the lanyard clips onto the long bolts

(1/2 x 3-1/4 inc h).

Note: Mak e sure the bent tab points to w ard

the head of the bolt.

Figure 7

3. Lightly oil the ends of the center roll bar

section.

4. Loosely install the center roll bar section using

2 bolts (1/2 x 3-1/4 inc h) and 2 ﬂang e n uts

(1/2 inc h).

Note: Mak e sure the bolts are installed from

the outside of the roll bar .

Note: Mak e sure the lanyard tab is installed

as sho w and points forw ard.

Figure 8

5. Raise the roll bar into the upright position and

secure it with the pins and hair pin cotter pins

fastened to the lanyards

Figure 9

6. T or que all lo w er fasteners , attac hed to the

mac hine frame , to 30 ft-lb .

7. Tighten the center roll bar bolts (1/2 x 3-1/4

inc h) so it rotates freely with some resistance .

Note: No more than one thread should be

exposed outside the n ut.

Figure 10

8. Tighten the front knobs ag ainst the center roll

bar ends .

Figure 11

Step

Adding Fuel to the Machine

No Parts Required

Procedure

Add diesel to the mac hine before star ting it. R efer

to y our Operator’ s Manual. for the cor rect fuel and

procedure .

Step

Charging the Battery

No Parts Required

Procedure

Charging the batter y pr oduces gasses that

can explode and cause serious injur y .

• K eep cigar ettes, spar ks and ﬂames a w ay

fr om the batter y .

• Mak e sur e the ignition s witch is of f.

• V entilate when charging or using the

batter y in an enclosed space.

Important: Do not r un the machine with

the batter y disconnected; electrical dama ge

may occur to the engine.

Charg e the batter y . R efer to the Operator’ s Manual

for instr uctions .

Figure 12

Step

Checking the Machine forGrease

Parts needed for this step:

1 tube

Number 2 general purpose lithium baseor molybdenum base grease. (Purchaseseparately.)

Procedure

1. R emo v e the belt co v ers on domestic mac hines

as sho wn belo w .

Figure 13

2. R emo v e the belt co v ers and bolts on

inter national mac hines as sho wn belo w .

Figure 14

3. Chec k the tensioning ar m for g rease .

4. Chec k the g rease for the three spindle bearings .

If needed, add g rease until it comes out of the

lo w er seals .

5. Install the belt co v ers .

Figure 15

6. Chec k the g rease for the cooling fan belt idler

ar m.

7. Chec k the g rease for the dri v e belt idler ar ms .

Figure 16

8. Grease the pump belt idler ar m in the front

of the engine .

Figure 17

Step

Checking the Engine OilLevel

No Parts Required

Procedure

Before y ou star t the engine and use the mac hine ,

c hec k the oil lev el in the engine crankcase; refer to

Chec king the Oil Lev el in Operator’ s Manual.

Step

Preparing the SideDischarge Chute

No Parts Required

Procedure

R emo v e the plastic tie holding the side disc harg e

c hute up and lo w er the c hute into place .

Step

Checking the Machine Before Delivery to the Customer

No Parts Required

Procedure

Before deli v ering the mac hine to the customer , ensure that y ou perfor m or ha v e perfor med the

procedures listed in the follo wing table and initial eac h when ﬁnished. R efer to the Operator’ s Manual

for instr uctions on perfor ming these procedures .

Initial

Check Procedure

Check the tire pressure.

Check the level of the mower.

Check that all mower spindles are greased.

Check the engine oil level.

Check the hydraulic uid level.

Check ROPS is secure.

On liquid cooled machines, check the level of the coolant in the radiator and overow bottle.

Check the adjustment of the parking brake.

Ensure that the machine tracks correctly; refer to the Operator’s Manual for the adjustmentprocedure.

Check the safety interlock system; refer to the Operator’s Manual .

Ensure that the PTO works.

Check all fasteners you installed to ensure that they are tight.

W hen y ou ﬁnish setting up the mac hine , sign and date in the space pro vided belo w:

Signature: Date:

Step

Delivering the Machine to the Customer

Parts needed for this step:

Operator’s Manual

Parts Catalog

Engine Owner’s Manual

Registration Card

Safety Video

2 Key

Procedure

At deli v er y , complete the items listed in the follo wing table and initial eac h when ﬁnished.

Model No. Serial No.

Dealer Initial Customer Initial Check Procedure

Show the customer where the following features are located and howthey function:

Fuel tank caps

Oil ll cap/ Oil dipstick

Engine oil lter

Engine oil drain

Fuel lters

Air lter

Radiator coolant

Hydraulic uid reservoir

Hydraulic lter

Battery

Ignition switch

Throttle lever

Glow plug light and switch

Power take off switch (PTO)

Motion control levers

Parking brake

Mower height-of-cut

Lift assist lever

Z Stand®

Adjustable seat

Hydraulic bypass valves

Rollover Protection System (ROPS)

Mower deck ow bafe

Refer to the Operator’s Manual to point out safety procedures, operation,and maintenance procedures.

Review the warranty statement as shown in the Operator’s Manual.

Describe the post sale service procedures for your store.

Assist the customer in lling out and mailing the registration card orregister online at www.Toro.com

Make sure that the customer receives the Operator’s Manual, Parts Catalog,Engine Owner’s Manual, Set Up Instructions, and safety video.

Assist the customer in loading the mower.

Note: W hen y ou, the dealer re presentati v e , ha v e ﬁnished deli v ering the mac hine to the customer , sign

and date in the space pro vide belo w and k ee p a copy of this pag e for dealer records .

Signature: Date:

Inhaltsverzeichnis

Andere Toro Rasenmäher Handbücher

Toro

Toro Super Recycler 21565 Bedienungsanleitung

Toro

Toro Groundsmaster 4500-D Bedienungsanleitung

Toro

Toro Recycler 20009 Bedienungsanleitung

Toro

Toro 74969 Bedienungsanleitung

Toro

Toro 30674 Bedienungsanleitung

Toro

Toro 20355 Bedienungsanleitung

Toro

Toro Super Recycler 21566T Bedienungsanleitung

Toro

Toro 22188TE Bedienungsanleitung

Toro

Toro Tru Trak Sulky 30110 Bedienungsanleitung

Toro

Toro 02617 Bedienungsanleitung

Toro

Toro TITAN 121-5680 Bedienungsanleitung

Toro

Toro Reelmaster 3555 Bedienungsanleitung

Toro

Toro 74691 Bedienungsanleitung

Toro

Toro Z Master Professional 7500-DSeries Handbuch

Toro

Toro Greensmaster TriFlex 3300 Bedienungsanleitung

Toro

Toro 20013 Bedienungsanleitung

Toro

Toro Recyler 20333 Bedienungsanleitung

Toro

Toro 02611 HoverPro 550 Bedienungsanleitung

Toro

Toro 4384 Bedienungsanleitung

Toro

Toro 74212 Bedienungsanleitung

Toro

Toro TimeCutter HD ZX5400 Handbuch

Toro

Toro Super Bagger 20192 Bedienungsanleitung

Toro

Toro 78253 Bedienungsanleitung

Toro

Toro TimeCutter Z5000 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 050 thru 062 Bedienungsanleitung