Toshiba 4400 Series Bedienungsanleitung

4400 Series UPS Seismic Kit Installation Instructions – 94016-001

4400 Series UPS Seismic Adapter Kit

Installation Instructions

Date: October 2015

Doc. No.: 94016-001

The 4400 Series cabinets can be installed to meet California OSHPD seismic specications using the

optional Seismic Kit and the oor anchorages specied below.

These instructions describe how to install the seismic adapter kits on the 4400 Series UPS, Battery , and

Auxiliary Cabinets. There is a SEISMIC KIT for each cabinet style: 15-30 kVA, 50 kVA, and 80 kVA.

1. 4400 15-30kVA Seismic Installation

2. 4400 50kVA Seismic Installation

3. 4400 80kVA Seismic Installation

1. 4400 15-30kVA Seismic Installation

Table 1 lists the contents of the 4400 15-30kVA Seismic Kit. Figure 1 shows the order of assembly for the

[bolt + lockwasher + washer] fastener group.

TABLE 1 15-30KVA SEISMIC CONTENTS

440300SEISMICKIT Contents

No. P/N* Description Quan

1 93437 TOP SEISMIC BRACKET 30kVA) 1

3 67813 BASE MOUNTING BRACKET, 1

4-a –Hex Bolt, 1/4—20,1-1/2” 1

4-b –Flat Washer, 1/4 1

4-c –E—Ring, F/0.25 Shaft 1

11-a –Hex Bolt, 5/16—18 x 1” 10

11-b –Lock Washer, 5/16 10

11-c –Flat Washer, 5/16 10

–94016 4400 Seismic Kit Installation

Manual

FIGURE 1: FASTENER GROUP

(BOLT +LOCK WASHER +

WASHER) Cabinet Footprint

1.75 in

(44.4 mm)

2.75 in

(70 mm)

2.0 in

(51 mm)

Conduit Knock-out

(3 Places)

34.05 in.

(865 mm)

12 in (305 mm) 12 in (305 mm)

9.22 in (234 mm)

4.28 in

(109 mm)

5.55 in

(141 mm)

Base Plate Footprint

1/2 in. Bolt (6)

FIGURE 2: 15-30KVA SEISMIC

ANCHORAGE - FLOOR PATTERN

24400 Series UPS Seismic Kit Installation Instructions – 94016-001

15-30 kVA Seismic Adapter Kit (Cont.)

1. Prepare the oor anchorages. Arrange the anchorages to ac-

commodate the nal layout including placement of ancillary bat-

tery and/or Auxiliary cabinets. (Figure 2)

2. Prepare the wall anchorages. Key measurements off the an-

chorage placement in Step 1. (Figure 3)

3. Table 1 lists the components of the 30kVA Seismic Kit. Figure 4

show the Seismic anchorage components in the Seismic Kit for

the 30kVA cabinets.

4. Assemble the fastener groups in Table 1, [4a-4c], [10a-10c], and

[11a-11c] as shown in Figure 1.

5. Secure the Top Seismic Bracket [1] to the top rear of the UPS

using two (2) fastener group [11]. (Figure 5)

6. Install the Base Brackets, [2], on the UPS base. Use two (2)

fastener group [10] for each bracket. (Figure 6)

7. Secure the Base Mounting Bracket, [3], to the oor anchors

installed in Step 1.

8. Roll the 15-30 kVA UPS cabinet between the two vertical sides of

the Base Mounting Bracket, [4]. (Figure 7)

9. Line up the UPS so the bolt holes on the Bottom Seismic Brack-

ets line up with the holes on the Seismic Base Plate vertical

sides.

10. Secure the UPS to the Seismic Base Plate using the remaining

eight (8) fastener group [11]. Insert the bolts through the Seismic

Bracket to the welded nuts on the Seismic Base Plate. (Figure

11. Secure the Top Seismic Bracket, [1], to the wall anchors installed

in Step 2.

12. Once installation is complete, use the single Fastener Group [4]

to secure the door of the UPS. (Figure 8)

FIGURE 5: TOP SEISMIC BRACKET INSTALLATION

FIGURE 3: 15-30KVA SEISMIC

ANCHORAGE - WALL PATTERN

66.44 in. (1688 mm)

10.05 in

(255 mm)

5 in (127 mm)

1/4” Bolt

Anchor (2)

9.27 in

(471 mm)

Base Mounting Bracket

Cabinet Wall Footprint

P/N 440300SEISMICKIT

FIGURE 4: SEISMIC KIT

COMPONENTS (15-30 KVA)

4400 Series UPS Seismic Kit Installation Instructions – 94016-001

15-30 kVA Seismic Adapter Kit (Cont.)

10 10

FIGURE 6: BOTTOM SEISMIC BRACKET INSTALLATION

11 11

Slide UPS into

Base Plate

FIGURE 7: INSTALLING ON SEISMIC BASE PLATE

FIGURE 8: SEISMIC DOOR ANCHOR (15-30 KVA)

44400 Series UPS Seismic Kit Installation Instructions – 94016-001

FIGURE 9: SEISMIC 15-30 KVA DIMENSAIONAL DRAWING

4400 Series UPS Seismic Kit Installation Instructions – 94016-001

2. 4400 50kVA Seismic Installation

Table 2 lists the contents of the 4400 50kVA (4400500SEISMICKIT) and 80kVA (4400800SEISMICKIT)

Seismic Kits. Figure 1 shows the order of assembly for the [bolt + lockwasher + washer] fastener group.

TABLE 2 50 KVA SEISMIC KIT CONTENTS

440500SEISMICKIT Contents

No. P/N* Description Quan

5 66437 TOP SEISMIC BRACKET 1

667193 SEISMIC MOUNTING CHANNEL 2

7-a –Hex Bolt, 1/4—20,1-1/2” 1

7-b –Flat Washer, 1/4 1

7-c –E—Ring, F/0.25 Shaft 1

10-a –Hex Bolt, 1/2—13 x 3/4” 8

10-b –Lock Washer, 1/2 8

10-c –Flat Washer, 1/2 8

11-a –Hex Bolt, 5/16—18 x 1” 4

11-b –Lock Washer, 5/16 4

11-c –Flat Washer, 5/16 4

–94016 4400 Seismic Kit Installation Manual 1

1. Prepare the oor anchorages. Arrange the anchorages to ac-

commodate the nal layout including placement for ancillary

battery and/or Auxiliary cabinets. (Figure 11)

2. Prepare the wall anchorages. Key measurements off the an-

chorage placement in Step 1. (Figure 12)

3. Table 2 lists the components of the 50kVA Seismic Kit. Figure 10

show the Seismic anchorage components in the Seismic Kit for

the 50kVA cabinets.

4. Assemble the fastener groups in Table 2, [7a-7c], [10a-10c], and

[11a-11c] as shown in Figure 1.

5. Secure the Top Seismic Bracket [5] to the top rear of the UPS

using three (3) fastener group [11]. (Figure 13)

6. Position the UPS over the oor anchors

7. Slip each Seismic Mounting Channel [6] over the three oor

anchors on each side of the UPS.

8. Tilt the Base bracket up against the UPS bottom bracket on the

UPS base.

9. Align the holes in the Seismic Mounting Channels [6] with the

UPS bottom brackets.

10. Use the remaining eight (8) fastener group [11] to secure the

Seismic Mounting Channels [6] to the UPS bottom brackets.

(Figure 14, Figure 15)

11. Secure the Top Seismic Bracket to the wall anchors using 5/16” Bolts.

12. Once installation is complete, secure the door of the UPS using the two

(2) Fastener Group [7]. (Figure 16)

FIGURE 1: FASTENER

GROUP (BOLT +LOCK

WASHER + WASHER)

P/N 440500SEISMICKIT

FIGURE 10: SEISMIC KIT

COMPONENTS (50 KVA)

64400 Series UPS Seismic Kit Installation Instructions – 94016-001

FIGURE 11: 50KVA SEISMIC

ANCHORAGE - FLOOR PATTERN

28.06 in. (713 mm)

11.5 in. (292 mm) 11.5 in. (292 mm)

4.59 in

(112 mm)

2.03 in

(51 mm)

37.2 in. (944 mm)

32.1 in. (816 mm)

5/8 in. Bolt Anchor (6)

FIGURE 14: BOTTOM SEISMIC BRACKET INSTALLATION

(FLOOR AND ANCHORS NOT SHOWN)

Bottom

Bracket

P/N 67193

FIGURE 12: 50KVA SEISMIC

ANCHORAGE - WALL PATTERN

5/16 in. Bolt

Anchor (4)

7.0 in

(178 mm)

75.01 in. (1905 mm)

7.0 in

(178 mm)

10.0 in

(254 mm)

5.0 in

(127 mm)

14.03 in

(356 mm)

Seismic

Mounting

Channel

32.1 in. (816 mm)

4.06 in

(103 mm)

FIGURE 13: TOP SEISMIC BRACKET INSTALLATION

11 11 11

Top Bracket

P/N 66437

4400 Series UPS Seismic Kit Installation Instructions – 94016-001

FIGURE 16: SEISMIC DOOR

ANCHOR (50-8/0 KVA)

Anchor Bolt

5/16 in x 18

Press Nut

5/16 in x 18 Bolt

5/16 in Lock Washer

5/16 Washer

11 Fastener Group

FIGURE 15: 50 KVA SEISMIC FLOOR ANCHOR - DETAIL

84400 Series UPS Seismic Kit Installation Instructions – 94016-001

FIGURE 17: SEISMIC 50 KVA DIMENSAIONAL DRAWING

4400 Series UPS Seismic Kit Installation Instructions – 94016-001

3. 4400 80kVA Seismic Installation

Table 3 lists the contents of the 4400 80kVA Seismic Kit 4400800SEISMICKIT. Figure 1 shows the order of

assembly for the [bolt + lockwasher + washer] fastener group.

TABLE 3 80 KVA SEISMIC KIT CONTENTS

440800SEISMICKIT Contents

No. P/N* Description Quan

5 66437 TOP SEISMIC BRACKET 1

7-a –Hex Bolt, 1/4—20,1-1/2” 2

7-b –Flat Washer, 1/4 2

7-c –E—Ring, F/0.25 Shaft 2

11-a –Hex Bolt, 5/16—18 x 1” 4

11-b –Lock Washer, 5/16 4

11-c –Flat Washer, 5/16 4

–94016 4400 Seismic Kit Installation Manual 1

80 kVA

1. Prepare the oor anchorages. Arrange the anchorages to ac-

commodate the nal layout including placement for ancillary

battery and/or Auxiliary cabinets. (Figure 19)

2. Prepare the wall anchorages. Key measurements off the an-

chorage placement in Step 1. (Figure 20)

3. Table 3 lists the components of the 80kVA Seismic Kit. Figure 18

show the Seismic anchorage component in the Seismic Kit for

the 80kVA cabinets.

4. Assemble the fastener groups in Table 3, [7a-7c] and

[11a-11c] as shown in Figure 1.

5. Secure the Top Seismic Bracket [5] to the top rear of the UPS

using three (3) fastener group [11]. (Figure 21)

6. Position the 80 kVA cabinet over the four oor anchors and se-

cure the unit.

7. Secure the Top Seismic Bracket to the wall anchors using 5/16”

Bolts.

8. Once installation is complete, secure the door of the cabinet us-

ing the two (2) Fastener Group [7]. (Figure 16)

FIGURE 1: FASTENER

GROUP (BOLT +LOCK

WASHER + WASHER)

P/N 440800SEISMICKIT

80 kVA 5

FIGURE 18: SEISMIC KIT

COMPONENTS (50 KVA)

10 4400 Series UPS Seismic Kit Installation Instructions – 94016-001

FIGURE 19: 80KVA SEISMIC

ANCHORAGE - FLOOR PATTERN

27.74 in. (704 mm)

27.1 in. (689 mm)

2.5 in

(64 mm)

2.5 in

(64 mm)

37.2 in. (944 mm)

32.1 in. (816 mm)

5/8 in. Bolt Anchor (4)

FIGURE 20: 80KVA SEISMIC

ANCHORAGE - WALL PATTERN

5/16 in. Bolt

Anchor (4)

7.0 in

(178 mm)

74.98 in. (1904 mm)

7.0 in

(178 mm)

10.0 in

(254 mm)

5.0 in

(127 mm)

13.55 in

(344 mm)

Base

C-Channel

32.1 in. (816 mm)

11 11 11

FIGURE 21: TOP SEISMIC BRACKET INSTALLATION

Andere Handbücher für 4400 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Adapter Handbücher

Toshiba

Toshiba B-FP800-AC-QM-S Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-S15 series Bedienungsanleitung

Toshiba

Toshiba TransferJet Bedienungsanleitung

Toshiba

Toshiba TCB-PCNT20E Bedienungsanleitung

Toshiba

Toshiba TCB-DK01SS-E Bedienungsanleitung

Toshiba

Toshiba TCB-SS1UU-E Bedienungsanleitung

Toshiba

Toshiba Sitecom CN-512 Montageanleitung

Toshiba

Toshiba WLM-10UB1 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-S15 series Bedienungsanleitung

Toshiba

Toshiba TransferJet Bedienungsanleitung

Toshiba

Toshiba Canvio Cast Bedienungsanleitung

Toshiba

Toshiba B-EP800-DC48-QM-R Bedienungsanleitung

Toshiba

Toshiba B-EP802-DC12-QM-R Bedienungsanleitung

Toshiba

Toshiba B-EP800-AC-QM-R Bedienungsanleitung

Toshiba

Toshiba GN-2010 Bedienungsanleitung

Toshiba

Toshiba B-FP800-DCJA-QM-R Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-S15 series Bedienungsanleitung

Toshiba

Toshiba WUS-G06G-JT Bedienungsanleitung

Toshiba

Toshiba TransferJet Bedienungsanleitung

Toshiba

Toshiba WLM-10NB1 Bedienungsanleitung

Toshiba

Toshiba GN-1010 Bedienungsanleitung

Toshiba

Toshiba CANVIO Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

RCA

RCA AH57R Bedienungsanleitung