Toshiba 352/452 Bedienungsanleitung

User Guide

Basic Fax Features

Training and Dealer Development

Page 1

BASIC FAX FEATURES

Sending a FAX

Preparation for Transmission

Setting Originals

Setting the Transmission Conditions

Specifying the Remote Fax

Sending Originals

Receiving a FAX

Reception Modes

Reception Settings

Sending a FAX

Preparation for Transmission

Switching to the FAX Mode

1. Press the FAX button on the control panel to select the

Fax function.

yBe sure to switch over to the Fax mode before

carrying out Fax operations.

yIf you leave the digital copier for about 45 seconds,

it automatically returns to the copy mode.

yYou can also switch to the Fax mode when the

digital copier is in the energy-saving mode.

Page 2

Sending a FAX (Cont’d.)

Setting Originals

When Setting Originals on the Glass

NOTE: Originals are sent in the order they are placed on the original glass in both the

memory TX and direct TX modes.

1. Raise the Reversing Automatic Document Feeder, place

the original (A) with its face down on the glass. Raise it

60 degrees or more to detect the original.

2. Align the original against the left inner corner of

the glass.

yDifferent size originals can also be sent in one

transmission.

yWhen LD, LG, LT-R, ST, COMP, A3, A4-R, A5,

B4, B5 or FOLIO originals are placed as shown in the

figure on the right, the pre-entered sender information

is printed in the shaded position shown (B) in the

figure and sent to the remote Fax.

yWhen LT, ST-R, A4, A5-R or B5-R originals are

placed as shown in the figure on the right, the pre-

entered sender information is printed in the shaded

position shown (C) in the figure and sent to the

remote Fax.

3. Lower the Reversing Automatic Document Feeder slowly.

Page 3

Sending a FAX (Cont’d.)

Setting Originals

When Using the Reversing Automatic Document Feeder

NOTE: When the originals are placed on the Reversing Automatic Document Feeder, the

uppermost page is first scanned and sent.

1. After aligning the edges of originals, place them

with their face up and slide the guides to the width

of the originals.

yYou cannot mix A series format (A3, A4, A5)

and B series format (B4, B5) or LT series and

COMP. LT/A4 size originals are rotated 90oso

that they are sent as LT-R/ A4-R originals.

yIf a mixture of LD and LG, A3 and A4, or B4

and B5 originals are placed, they are sent in their

original sizes.

yWhen LD, LG, LT-R, COMP, A3 and B4, A4-R,

B5 originals are placed as shown in the figure on the

right, the pre-entered sender information is printed in

the shaded position shown (A) in the figure and sent

to the remote Fax.

yWhen LT, ST-R, A4, A5-R or B5-R originals

are placed as shown in the figure on the right, the

pre-entered sender information is printed in the

shaded position shown (B) in the figure and sent to

the remote Fax.

Page 4

Sending a FAX (Cont’d.)

Setting the Transmission Conditions

Originals can be sent using different transmission conditions (resolution, image quality mode,

exposure, transmission mode, original size, ECM, quality TX, Line, SUB/SEP/SID, PWD,

subject and body). Settings for the subject and body are available only when using a function

of the Internet Fax. If you change the transmission conditions, the new settings are valid for

one transmission only. They are returned to the default settings after transmission.

1. Place the original(s).

2. Press the FAX button on the control panel.

3. Press the ADDRESS button to enter the address menu,

and then press the OPTION button.

4. Press the desired buttons. Press the Prev or Next button to

switch the screens. The highlighted buttons in the screens

on the right are the default settings.

5. Press the ENTER button to complete the setting.

6. Specify the remote Fax and press the START button.

TIPS: When one remote Fax is specified by the address book,

and the OPTION button is selected, the contents of

the address setting will be reflected to the OPTION.

The settings of the TX type, ECM, quality TX, line

select, SUB/ SEP and SID/PWD selected in the

OPTION have priority.

Page 5

Sending a FAX (Cont’d.)

Specifying the Remote Fax

Direct Entry with Digital Keys

1. Place the original(s).

2. Press the FAX button on the control panel

3. Key in the remote Fax number.

4. If you make a mistake, press the CLEAR button on the

control panel or the BACK SPACE button in the address

menu and correct the mistake.

yCLEAR button: Press this button to clear all values

you have entered.

yBACK SPACE button: Press this button to delete each

value you have.

TIP: When you are dialing to an outside line via a PBX, there may be a pause before the

connection is made, causing a transmission error. To avoid this error, press the

MONITOR/PAUSE button after the number that designates an outside line to enter a

pause. This automatically enters a 3-second pause before the remote Fax number is dialed,

which reduces transmission errors. (The mark “-” is displayed as a “pause” on the screen.)

5. Press the START button.

Address Book Entry

Address book entry is the method for specifying remote Fax

numbers by pressing the remote Fax buttons which have

previously been registered. It is convenient if frequently

used destinations are registered in the address book.

1. Place the original(s).

2. Press the FAX button on the control panel.

3. Press the ADDRESS button to enter the address menu.

Each screen displays 8 destinations. To view destinations

not displayed on the screen, press the Prev or Next button

to switch the screens.

4. Press the button designating the remote Fax to which you

wish to send your transmission.

5. Press the START button.

Page 6

Sending a FAX (Cont’d.)

Specifying the Remote Fax (Cont’d.)

Group Entry

Group entry is the method of specifying remote Fax numbers by pressing the group button

which has previously been entered. It is convenient if multiple frequently used multiple

destinations are entered into a group.

1. Place the original(s).

2. Press the FAX button on the control panel.

3. Press the ADDRESS button to enter the address

menu, then Press the GROUP button. Each screen

displays 8 destinations. To view destinations not

displayed on the screen, press the Prev or Next button

to switch the screens.

4. Press the remote Fax group to send originals. If you

want to see the specified group members, press the

CONTENTS button. You can search for groups by ID

number and by group.

TIP: The Remote Faxes in the group can be confirmed in

the group number information. See the User Functions

Guide.

5. Press the START button.

Page 7

Specifying the Remote Fax (Cont’d.)

Multi-Address Transmission

The Multi-Address Transmission function allows you to send the same original to 2 or

more remote Faxes in a single operation, which can be done by combining direct, address

book and group entry. Combining with the Internet Fax is also available. This eliminates

the trouble of placing the original and then dialing the number for each destination.

Multi-address transmissions must be set in the memory TX mode.

The following shows the number of destinations that can be entered according to how the

remote Fax is specified:

yBy direct entry only: 400 destinations

yBy address book entry only: 400 destinations

yBy group entry only: 200 groups (400 destinations per a group)

yBy combining direct, address book and group entry: 400 destinations

1. Place the original(s).

2. Press the FAX button on the control panel.

3. Press the OPTION button and set the transmission conditions.

4. Specify the remote Fax numbers.

yTo continuously enter remote Fax numbers after

having specified them by means of the digital keys,

press the MULTI button, then enter the next number.

You do not need to press the MULTI button for the

address book or the group entry.

yThe selected destinations can be confirmed by

selecting the DESTINATION button.

TIPS: To cancel the remote Fax number entered with digital keys, press the CLEAR

button on the control panel.

To cancel a remote Fax specified with address book or group entry, press the

highlighted button for the remote Fax again. To cancel all specified remote Faxes,

press the ALL CLEAR button.

To cancel a remote Fax specified with direct entry, press the DESTINATION

button to enter the destination menu, and then cancel it.

5. Specify all remote Faxes, then press the START button.

Page 8

Sending a FAX (Cont’d.)

Specifying the Remote Fax (Cont’d.)

Searching by ID Number

When selecting the remote Faxes registered in the address and group by searching by the

ID number immediately displays the screen including the searched-for ID number.

1. Place the original(s).

2. Press the FAX button on the control panel.

3. Press the ADDRESS button to enter the address menu,

then the KNOWN ID button.

4. Key in the desired ID number, and press the ENTER

button. You can key in the number within the range of

1 to 1000.

5. Press the button for the remote Fax that you want to

send to.

yEach screen displays 8 destinations.

yTo view destinations not displayed on the screen,

press the Prev or Next button to switch the screens.

TIPS: To continue searching by ID number, press the KNOWN ID button.

To continue searching by address, press the SEARCH ADDRESS button.

6. Press the START button.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Multifunktionsdrucker Handbücher

Toshiba

Toshiba e-STUDIO163 Anleitung zur Verwendung

Toshiba

Toshiba e-STUDIO3511 Anleitung zur Verwendung

Toshiba

Toshiba E-studio 281c Konfigurationshandbuch

Toshiba

Toshiba e-studio905 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO160 Anleitung zur Verwendung

Toshiba

Toshiba e-STUDIO287CS Bedienungsanleitung

Toshiba

Toshiba E-STUDIO5506AC Bedienungsanleitung

Toshiba

Toshiba E-STUDIO202S Einrichtungshandbuch

Toshiba

Toshiba e-STUDIO355 Bedienungsanleitung

Toshiba

Toshiba e-studio5560c Bedienungsanleitung

Toshiba

Toshiba e-studio 901 Bedienungsanleitung

Toshiba

Toshiba e-Studio477s Bedienungsanleitung

Toshiba

Toshiba E-STUDIO E-Studio 3511 Bedienungsanleitung

Toshiba

Toshiba E-STUDIO900 Installationsanleitung

Toshiba

Toshiba e-studio2007 Bedienungsanleitung

Toshiba

Toshiba e-studio 2555c Bedienungsanleitung

Toshiba

Toshiba e-STUDIO6550c Series Bedienungsanleitung

Toshiba

Toshiba E-studio 5520c Konfigurationshandbuch

Toshiba

Toshiba GD-1151 Bedienungsanleitung

Toshiba

Toshiba GD-1250 Bedienungsanleitung

Toshiba

Toshiba E-studio5540c Bedienungsanleitung

Toshiba

Toshiba GN-1041 Bedienungsanleitung

Toshiba

Toshiba Copier Bedienungsanleitung

Toshiba

Toshiba e-studio 2506 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung