Toshiba E-studio 160 Bedienungsanleitung

SERVICE MANUAL

DIGITAL MULTI FUNCTION

e-STUDIO160/200/250

File No. SME020009A0

R02092123701-TTEC

Ver01_2007-10

December 2002 TOSHIBA TEC e-STUDIO160/200/250 GENERAL PRECAUTIONS

GENERAL PRECAUTIONS REGARDING THE INSTALLATION AND

SERVICE FOR e-STUDIO160/200/250 SERIES

The installation and service should be done by a qualified service technician.

1. Transportation

• When transporting/installing the copier, employ two persons and be sure to use the positions as

indicated below.

The copier is fairly heavy and weighs approximately 50 kg (110 lb), therefore pay full attention

when handling it.

2. Installation

• Be sure to use a dedicated outlet with AC 115 or 120V/15A (220V, 230V, 240V/10A) or more for its

power source.

• The copier must be grounded for safety.

Never ground it to a gas pipe or a water pipe.

• Select a suitable place for installation.

Avoid excessive heat, high humidity, dust, vibration and direct sunlight.

• Also provide proper ventilation as the copier emits a slight amount of ozone.

• To insure adequate working space for the copying operation, keep a minimum clearance of 80

cm (32") on the left, 80 cm (32") on the right and 10 cm (4") in the rear.

• After having installed the copier, be sure to push the carrying handles into the copier.

3. Service of Machines

• Basically, be sure to turn the main switch off and unplug the power cord during service.

• Be sure not to touch high-temperature sections such as the exposure lamp, the fuser unit, the

damp heater and their periphery.

• Be sure not to touch high-voltage sections such as the chargers and the high-voltage transformer.

• Be sure not to touch rotating/operating sections such as gears, belts, pulleys, fans, etc.

• When servicing the machines with the main switch turned on, be sure not to touch live sections

and rotating/operating sections. Avoid exposure to laser radiation.

• Use suitable measuring instruments and tools.

4 portions

e-STUDIO160/200/250 GENERAL PRECAUTIONS December 2002 TOSHIBA TEC

• Avoid exposure to laser radiation during servicing.

– Avoid direct exposure to beam.

– Do not insert tools, parts, etc. that are reflective into the path of the laser beam.

– Remove all watches, rings, bracelets, etc. that are reflective.

4. Main Service Parts for Safety

• The breaker, door switch, fuse, thermostat, thermistor, etc. are particularly important for safety.

Be sure to handle/install them properly.

5. Cautionary Labels

• During servicing, be sure to check the rating plate and the cautionary labels such as “Unplug the

power cord during service”, “Hot area”, “Laser warning label” etc. to see if there is any dirt on their

surface and whether they are properly stuck to the copier.

6. Disposition of Consumable Parts/Packing Materials

• Regarding the recovery and disposal of the copier, supplies, consumable parts and packingm a -

terials, it is recommended to follow the relevant local regulations or rules.

7. When parts are disassembled, reassembly is basically the reverse of disas-

sembly unless otherwise noted in this manual or other related documents. Be

careful not to reassemble small parts such as screws, washers, pins, E-rings,

toothed washers in the wrong places.

8. Basically, the machine should not be operated with any parts removed or dis-

assembled.

9. Precautions Against Static Electricity

• The PC board must be stored in an anti-electrostatic bag and handled carefully using a wristband,

because the ICs on it may become damaged due to static electricity.

Caution: Before using the wrist band, pull out the power cord plug of the copier and make

sure that there is no uninsulated charged objects in the vicinity.

Caution: Dispose of used batteries and RAM-ICs including lithium batteries according to the

manufacturer's instructions.

Attention: Se débarrasser de batteries et RAM-ICs usés y compris les batteries en lithium

selon les instructions du fabricant.

Vorsicht: Entsorgung des gebrauchten Batterien und RAM-ICs (inklusive der Lithium-Batterie)

nach Angaben des Herstellers.

1. SPECIFICATIONS • ACCESSORIES •

OPTIONS • SUPPLIES ........................... 1-1

1.1 Specifications ............................................................................................ 1-1

1.2 Accessories .............................................................................................. 1-5

1.3 Options ..................................................................................................... 1-6

1.4 Replacement Units/Supplies ..................................................................... 1-6

1.5 System List ............................................................................................... 1-7

December 2002 TOSHIBA TEC 1 - 1 e-STUDIO160/200/250 SPECIFICATIONS

1. SPECIFICATIONS • ACCESSORIES • OPTIONS • SUPPLIES

1.1 Specifications

• Copy process ................ Indirect electrophotographic process (dry)

• Type ............................... Desktop type (console type when the paper feed pedestal and Large

capacity feeder are installed)

• Original table ................. Fixed table (the left rear corner used for standard original placement)

• Acceptable originals ...... Type: sheet, book, and 3-dimensional object.

However, the automatic document feeder (option) only accepts sheets of

paper (Multi-sheet: 50 - 105 g/m2, or 13 - 29 lb/Single-sheet: 105 - 127

g/m2, or 29 - 34 lb.), excluding carbon paper, pasted sheets and stapled

sheets.

Max size: A3/LD

• Copy speed

e-STUDIO160 series (Copies/min.)

Upper PFU PFP LCF Bypass feeding (SFB)

cassette Upper Lower cassette No paper size Paper size

cassette (with CM) designated designated

A4, LT 20 20 20 20 20 12 20

A4-R 16 16 16 16 - 12 16

LT-R 17 17 17 17 - 12 17

B4 14 14 14 14 - 12 14

LG 14 14 14 14 - 12 14

A3, LD 12 12 12 12 - 12 12

Paper

size

Paper

supply

e-STUDIO200 series (Copies/min.)

Upper PFU PFP LCF Bypass feeding (SFB)

cassette Upper Lower cassette No paper size Paper size

cassette (with CM) designated designated

A4, LT 16 16 16 - - 9 16

A4-R 12 12 12 - - 9 12

LT-R 13 13 13 - - 9 13

B4 11 11 11 - - 9 11

LG 11 11 11 - - 9 11

A3, LD 9 9 9 - - 9 9

Paper

size

Paper

supply

e-STUDIO160/200/250 SPECIFICATIONS 1 - 2 December 2002 TOSHIBA TEC

Cassette Duplexing Bypass copy Remarks

Size A3 - A5-R, FOLIO A3 - A5-R, FOLIO

LD - ST-R, COM LD - ST-R, COM

Weight 64 - 80 g/m2Continuous copy: 64 - 80 g/m2, 17 - 21 lbs

17 - 21 lbs Single copy: 80 - 163 g/m2, 21 - 43 lbs

Special paper — — Recommended OHP film/Thick paper

* "-" shows "Cannot be used".

* The copy speeds in the above table are available when originals are manually placed for single-

side, multiple copying.

• System copy speed (Copies/min.)

* Copy speeds include the first copy time.

They are available when the copy modes in the above table are selected and 10 LT-size originals

are set in the automatic document feeder.

• Copy paper

Copy mode

Single-sided originals 1 set

3 sets

Single-sided copies (Non sort) 5 sets

Single-sided originals 1 set

3 sets

Two-sided copies (Sort) 5 sets

Two-sided originals 1 set

3 sets

Single-sided copies (Sort) 5 sets

Two-sided originals 1 set

3 sets

Two-sided copies (Sort) 5 sets

e-STUDIO250 series (Copies/min.)

Upper PFU PFP LCF Bypass feeding (SFB)

cassette Upper Lower cassette No paper size Paper size

cassette (with CM) designated designated

A4, LT 24.6 24.6 24.6 24.6 24.6 14 24.6

A4-R 19 19 19 19 - 14 19

LT-R 20 20 20 20 - 14 20

B4 16 16 16 16 - 14 16

LG 16 16 16 16 - 14 16

A3, LD 14 14 14 14 - 14 14

Paper

size

Paper

supply

e-STUDIO160

series

e-STUDIO200

series

e-STUDIO250

series

December 2002 TOSHIBA TEC 1 - 3 e-STUDIO160/200/250 SPECIFICATIONS

• First copy time ...................... e-STUDIO160 series: Less than 7.9 seconds (A4/LT, the Upper

cassette, 100%, original placed manually)

e-STUDIO200 series: Less than 7.0 seconds (A4/LT, the Upper

cassette, 100%, original placed manually)

e-STUDIO250 series: Less than 7.0 seconds (A4/LT, the Upper

cassette, 100%, original placed manually)

• Warming-up time .................. e-STUDIO160 series: Less than 60 seconds

e-STUDIO200 series: Less than 75 seconds

e-STUDIO250 series: Less than 75 seconds

• Multiple copying ................... Up to 999 copies; entry by numeric keys

• Reproduction ratio ................ Actual ratio: 100%

Zooming: 50 - 200% in increments of 1%

25 - 400% in increments of 1%

(for e-STUDIO200/250 series; with original cover)

• Resolution/Gradation ........... Read: 600 dpi x 600 dpi

Copy: 600 dpi x 600 dpi

Printer: 1200 dpi x 600 dpi

Fax: 16 dot/mm x 15.4 dot/mm (406 dpi x 392 dpi)

• Paper feeding ....................... Automatic feeding: Copier’s cassette 1 piece standard

e-STUDIO160 series: Expandable up to 3 pieces by installing

optional cassettes.

e-STUDIO200/250 series: Expandable up to 4 pieces by installing

optional cassettes.

PFU-optional (Stack height 60.5 mm, Equivalent to 550 sheets; 64 to

80 g/m2(17 to 21 lb.))

PFP-optional (Stack height 60.5 mm, Equivalent to 550 sheets; 64 to

80 g/m2(17 to 21 lb.))

LCF-optional (Stack height 165 mm, Equivalent to 1250 x 2 sheets;

64 to 80 g/m2(17 to 21 lb.))

Bypass feeding (Stack height 16 mm, Equivalent to 100 sheets; 64 to

80 g/m2(17 to 21 lb.))

• Capacity of originals of

automatic document feeder .. A4, A4-R, B5, B5-R, A5-R, LT, LT-R, ST-R: 50 sheets (with ADF)

B4, Folio, LG, Comp, A3, LD: 50 sheets (with ADF)

A4, A4-R, B5, B5-R, A5-R, LT, LT-R, ST-R: 100 sheets (with RADF)

B4, Folio, LG, Comp, A3, LD: 100 sheets (with RADF)

• Toner supplying .................... Automatic toner sensor detection

• Density control ...................... Automatic density mode and manual density mode selectable in 7

steps

e-STUDIO160/200/250 SPECIFICATIONS 1 - 4 December 2002 TOSHIBA TEC

e-STUDIO160 series e-STUDIO200/250 series

Standard 530 x 554 x 600 mm 530 x 554 x 600 mm

Standard + Original cover 530 x 554 x 643 mm 530 x 554 x 643 mm

Standard + ADF 530 x 554 x 731 mm 530 x 554 x 731 mm

Standard + RADF 545 x 599 x 772 mm 545 x 599 x 772 mm

Standard + ADU + RADF 607 x 599 x 772 mm 607 x 599 x 772 mm

Standard + Original cover + PFU 530 x 554 x 757 mm 530 x 554 x 757 mm

Standard + Original cover + PFU + PFP 530 x 554 x 1039 mm 530 x 554 x 1039 mm

Standard + Original cover + JSP 604 x 554 x 643 mm 604 x 554 x 643 mm

Standard + Original cover + SFB 801 x 554 x 643 mm 801 x 554 x 643 mm

Standard + Original cover + OCT 604 x 554 x 643 mm 604 x 554 x 643 mm

Standard + Original cover + Stapler 787 x 554 x 676 mm 787 x 554 x 676 mm

Standard + Original cover + Finisher ----- 957 x 554 x 643 mm

• Weight ................................ Standard: 50 Kg (110 lb.) (with Process unit/Toner cartridge)

Full system: 92 Kg (203 lb.) (e-STUDIO160 series)/

124 Kg (273 lb.) (e-STUDIO200/250 series)

• Power requirements ........... 115VAC, 50Hz/60Hz

120VAC, 50Hz/60Hz

127VAC, 50Hz/60Hz

220-240VAC, 50Hz/60Hz

• Power consumption ............ 1.4 KW or less

• Dimensions: ....................... (W) x (D) x (H) mm

03-3 03-4

e-STUDIO160 series

December 2002 TOSHIBA TEC 1 - 5 e-STUDIO160/200/250 SPECIFICATIONS

1.2 Accessories

* Machine version

NAD: North America

MJD: Europe

AUD: Australia

ASD: Asia

SAD: Saudi Arabia

CND: China

Setup instructions 1pc.

Operator’s manual 1pc.

Setup report 1pc. (for NAD and MJD)

Warranty sheet 1pc. (for NAD)

CS card 1pc. (for MJD)

Process unit 1pc.

Toner cartridge 1pc.

Detouchable power cord 1pc.

T-808

e-STUDIO200/250 series

T-101-2

Andere Handbücher für e-studio 160

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Multifunktionsdrucker Handbücher

Toshiba

Toshiba E-STUDIO 655 Bedienungsanleitung

Toshiba

Toshiba E-studio18 Bedienungsanleitung

Toshiba

Toshiba E-STUDIO2000AC Bedienungsanleitung

Toshiba

Toshiba e-STUDIO 520 Bedienungsanleitung

Toshiba

Toshiba E-STUDIO2000AC Bedienungsanleitung

Toshiba

Toshiba E-STUDIO2500AC Bedienungsanleitung

Toshiba

Toshiba E-STUDIO520 Anleitung zur Verwendung

Toshiba

Toshiba e-studio555 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO3510c Bedienungsanleitung

Toshiba

Toshiba e-studio 2330C Bedienungsanleitung

Toshiba

Toshiba E-studio2555c Bedienungsanleitung

Toshiba

Toshiba e-studio281c Bedienungsanleitung

Toshiba

Toshiba e-STUDIO 2303AM Bedienungsanleitung

Toshiba

Toshiba e-STUDIO206L Betriebsanleitung

Toshiba

Toshiba E-STUDIO202S Bedienungsanleitung

Toshiba

Toshiba E-studio 281c Konfigurationshandbuch

Toshiba

Toshiba E-STUDIO520 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO200L/230/280 SERIES Bedienungsanleitung

Toshiba

Toshiba e-STUDIO FASTstart 200L Bedienungsanleitung

Toshiba

Toshiba GA-1190 Bedienungsanleitung

Toshiba

Toshiba 5520 Programmierhandbuch

Toshiba

Toshiba e-STUDIO GL-1010 Service-Handbuch

Toshiba

Toshiba E-studio 2550c Bedienungsanleitung

Toshiba

Toshiba e-Studio 350 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Toshiba e-studio 160 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken