Toshiba CD332 Bedienungsanleitung

UM-TS03∗∗∗-E024

PROGRAMMABLE CONTROLLER

PROSEC T3

CHANGE DETECT DC INPUT MODULE

CD332

USER’S MANUAL

TOSHIBA CORPORATION

Important Information

Misuse of this equipment can result in property damage or human injury.

Because controlled system applications vary widely, you should satisfy yourself

as to the acceptability of this equipment for your intended purpose.

In no event will Toshiba Corporation be responsible or liable for either indirect

or consequential damage or injury that may result from the use of this equipment.

No patent liability is assumed by Toshiba Corporation with respect to use of

information, illustrations, circuits, equipment or examples of application in this

publication.

Toshiba Corporation reserves the right to make changes and improvements to this

publication and/or related products at any time without notice. No obligation shall be

incurred other than as noted in this publication.

This publication is copyrighted and contains proprietary material. No part of this book

may be reproduced, stored in a retrieval system, or transmitted, in any form or by any

means ⎯electrical, mechanical, photocopying, recording, or otherwise ⎯without

obtaining prior written permission from Toshiba Corporation.

Publication number: UM-TS03∗∗∗-E024

1st edition August 1996

PROSEC is a registered trademark of TOSHIBA Corporation.

User’s Manual 1

Safety Precautions

This module (CD332) is a change detect DC input module for Toshiba’s Programmable Controller

PROSEC-T3 or T3H (hereafter called T3 generically). Read this manual thoroughly before using

this module. Also, keep this manual and related manuals so that you can read them anytime while

this module is in operation.

Safety Symbols

The following safety symbols are used on the product and/or in the related manuals.

Pay attention to information preceded by the following symbols for safety.

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury. It may also be used to alert

against unsafe practices.

Safety Precautions

•Turn off power to the T3 and to the CD332 before removing or mounting the CD332.

Failure to do so can cause electrical shock or damage to this product.

•Read the Safety Precautions described in the T3 User’s Manual before using the T3

and the CD332.

•Follow the instructions described in this manual and in the T3 User’s Manual when

installing and wiring the T3 and the CD332.

•The CD332 has been designed for the T3. Use your CD332 only on the rack of the T3.

•Remove the CD332 from the rack before setting the jumper plugs on the CD332.

Do not touch other components on the CD332’s printed circuit board. It may cause

damage to the CD332.

•The CD332 consumes maximum 0.3 A of internal 5 Vdc power. Confirm that the total

5 Vdc consumed current per one power supply module is within the limit (7A).

If it exceeds the limit, the T3 cannot operate properly and this may cause unsafe

situation.

!WARNING

!CAUTION

2Change Detect DC Input Module (CD332)

About This Manual

This manual explains the specifications and operations of the Change Detect DC Input

Module (CD332) for Programmable Controller T3. Read this manual carefully before using

the CD332.

Inside This Manual

Section 1 Overview

This section introduces the CD332. The CD332 has an interrupt generation function for the

T3. This section outlines the CD332’s function. The external features of the CD332 are also

provided in this section.

Section 2 Specifications

This section provides the hardware and functional specifications of the CD332. The

information for external wire connections is also provided in this section.

Section 3 Mode Setting

The input delay time and the interrupt generation timings are user selectable. This section

explains the switch settings for this purpose.

Section 4 I/O Allocation

This section provides the information to design T3 program for the CD332. This section

explains the I/O allocation and functions of the I/O register assigned to the CD332.

Section 5 Programming

The CD332 generates an interrupt signal for the T3. This section provides T3’s sample

program for the CD332. Precautions for using the interrupt function are also explained in

this section.

User’s Manual 3

About This Manual

Related Manuals

The following related manuals are available for T3. Besides this manual, read the following

manuals for your better understanding.

T3 User’s Manual - Hardware

This manual covers the T3’s main body and basic I/O - their specifications, handling,

maintenance and services.

T3 User’s Manual - Functions

This manual explains the functions of the T3 and how to use them. The necessary

information to create user program is covered in this manual.

T3H User’s Manual

This manual explains the specifications of the T3H and the functional differences between

the T3H and the T3.

T-series Instruction Set

This manual provides the detailed specifications of instructions for Toshiba’s T-series

Programmable Controllers.

T-series Computer Link Function

This manual provides the information for a computer to communicate with T3 through the

T-series Programmable Controller’s Computer Link function.

T-PDS (Ver. 1.4) Basic Operation manual

This manual explains how to install the T-series program development system (T-PDS)

into your computer and provides basic programming operations.

T-PDS (Ver. 1.4) Command Reference Manual

This manual explains the T-series program development system (T-PDS) in detail.

T-PDS (Ver. 1.6) Expanded Functions

This manual explains the expanded functions on the T-PDS version 1.6. This manual

supplements the T-PDS (Ver.1.4) Command Reference Manual.

T-series Handy Programmer (HP911) Operation Manual

This manual explains the functions and key operations of the T-series Handy Programmer

(HP911).

Other than the listed above, some T3 related manuals for special I/O modules and data

transmission modules are available. Contact Toshiba for more information.

NOTE

4Change Detect DC Input Module (CD332)

Contents

Safety Precautions ...................................................................................... 1

About This Manual ...................................................................................... 2

Contents ..................................................................................................... 4

1. CD332 Overview ............................................................................. 5

1.1 Introduction ...................................................................................... 6

1.2 External features .............................................................................. 7

2. Specifications ................................................................................ 9

2.1 General specifications .................................................................... 10

2.2 Functional specifications ................................................................. 10

2.3 Input circuit .................................................................................... 11

2.4 Input signal connections ................................................................. 11

3. Mode Setting ................................................................................. 13

3.1 Input delay setting ........................................................................... 14

3.2 Interrupt generation timing setting ................................................... 15

4. I/O Allocation ................................................................................. 17

4.1 I/O allocation and I/O register ......................................................... 18

4.2 Interrupt assignment ....................................................................... 20

5. Programming ................................................................................ 21

5.1 T3 sample program ......................................................................... 22

5.2 Interrupt operation .......................................................................... 24

User’s Manual 5

Section 1

CD332 Overview

1.1 Introduction, 6

1.2 External features, 7

6Change Detect DC Input Module (CD332)

1. CD332 Overview

1.1 Introduction

The change detect DC input module CD332 (hereafter called CD332) is an 8 points 12

- 24 Vdc input module with interrupt generation function for Toshiba’s Programmable

Controller PROSEC-T3 or T3H (hereafter called T3 generically).

When the input signal status of the CD332 is changed, the CD332 generates an

interrupt for the T3. Then the T3 immediately stops ordinary operation and starts to

execute the pre-assigned I/O interrupt program.

The task switching time in the T3 is less than 500 µs. (under interrupt enable state)

The interrupt generation timing of the CD332 can be selected as follows for each input

point. This selection is made by the DIP switches provided on the front of the CD332.

(1) Rising edge (from OFF to ON)

(2) Falling edge (from ON to OFF)

(3) Both edges (both OFF to ON and ON to OFF)

This CD332 has 8 input points. By using one CD332, up to 8 interrupt factors can be

processed. On the other hand, up to 8 I/O interrupt programs are available in the T3.

Therefore, total up to 64 (= 8 ×8) interrupt factors can be processed by the T3 by using

8 CD332s.

The input voltage of the CD332 is 12 to 24 Vdc. The input delay time can be selected

either normal or high speed as 8 points block by setting the internal jumper plugs.

NOTE

The T3 supports 8 I/O interrupt programs. Therefore, maximum 8 CD332s

can be used with the T3.

Inhaltsverzeichnis

Andere Toshiba Computerhardware Handbücher

Toshiba

Toshiba GX7 Series Bedienungsanleitung

Toshiba

Toshiba TX49 TMPR4937 Bedienungsanleitung

Toshiba

Toshiba E3 Bedienungsanleitung

Toshiba

Toshiba Memory Module Stücklistenhandbuch

Toshiba

Toshiba B-EP700-WLAN-QM-R Bedienungsanleitung

Toshiba

Toshiba RemotEye III Bedienungsanleitung

Toshiba

Toshiba Libretto 50CT Bedienungsanleitung

Toshiba

Toshiba ETB003Z Bedienungsanleitung

Toshiba

Toshiba BCN002Z Bedienungsanleitung

Toshiba

Toshiba SD-BT00A Bedienungsanleitung

Toshiba

Toshiba Strata CIX40 Bedienungsanleitung

Toshiba

Toshiba GN-1060 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-MB1 Stücklistenhandbuch

Toshiba

Toshiba Stratagy Flash Bedienungs- und Wartungsanleitung

Toshiba

Toshiba Desk Station V Plus Bedienungsanleitung

Toshiba

Toshiba DA364/DA374 Bedienungsanleitung

Toshiba

Toshiba WN4301A-LF-JT Bedienungsanleitung

Toshiba

Toshiba TCB-PCIN3E Bedienungsanleitung

Toshiba

Toshiba e-studio1058 Leitfaden

Toshiba

Toshiba Stratagy Flash Bedienungsanleitung

Toshiba

Toshiba ETB004Z Bedienungsanleitung

Toshiba

Toshiba TCB-PSMT1E Bedienungsanleitung

Toshiba

Toshiba D660 Bedienungsanleitung

Toshiba

Toshiba TMP92CM22FG TLCS-900/H1 Series Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung