Toshiba TOSDIC-CIE DS Bedienungsanleitung





Installation and Wiring

Manual

6F8C0764

Toshiba Integrated Control System

Third Edition Dec, 1999

The contents of this manual may be revised without notice.

No part of this manual may be reproduced in any form without permission.

Safety Precautions

The instruction manual and the labels affixed to the products or equipment give important

information for using products safely. It helps prevent damage to properties and hazard to people

who use them or work with them.

Make yourself familiar with the signal words and signs in this page, then read the safety

precautions that follow and always follow the instructions to avoid hazards.

Explanation of signal words

Signal word is a word that designates a degree or level of hazard seriousness.

The words WARNING and CAUTION are used for the products.

WARNING Indicates a potentially hazardous situation which could result

in death or serious injury, if you do not follow the

instructions.

CAUTION Indicates a potentially hazardous situation which may result

in minor or moderate injury and/or property damage, if you

do not follow the instructions.

Hazard alert shapes and symbols

Following shapes and symbols are used in the safety precaution labels affixed to the

products and in other places including operation manuals for giving safety instructions.

Filled circle means "Mandatory Action" or "Do as indicated."

Required action is shown in the circle or described near the circle.

Circle band with a diagonal slash means "Prohibition" or " You must not do."

Prohibited action is shown in the circle or described near the circle.

Triangle means "Hazard Alerting" or "Be alert agaist hazard."

The kind of hazard is shown in the triangle or described near the triangle.

Exclamation point with a triangle is a safety alert symbol which indicates a

potential hazard. It is used with a Signal Word.

Square or rectangle means "Information Messages" or "Notice."

Important precautions for system operation

System fault or data loss may occur in the event of power outage whether it is external or

internal of the system. Take precautions in advance to protect the system in order to prevent such

event to take place. Also back up your data regularly to minimize the possible damage by loss of

data as a result of such event.

Safety Precautions

Confirmation of product safety label

Confirm that product safety labes are put on the front panel of the power supply module. If

the lavel is lost or soiled, inform TOSHIBA Corporation.

Safety Precautions

iii

1. Safety Precautions for Installation

WARNING

Grounding required:

To avoid the risk of electric shock or fire, be sure to ground the equipment.

CAUTION

Choose proper environment for installation:

Avoid installing and storing the equipment in the following environments:

zLocation with considerable dust

zLocation in which flammable or corrosive gases (such as SO2and H2S) are present

zLocation where vibration or shock exceeds allowable limits

zLocation where condensation may occur due to rapid change in temperature

zLocation where the temperature is not within the specified range for installation

zLocation where the humidity exceeds the specified limits for installation

zLocation in the direct sunlight

zLocation near a device that generates strong radio waves or magnetic fields

Considerations for maintenance and inspection:

Install the equipment in a place that facilitates maintenance and inspection. If not, in case of

malfunctioning, it may hinder the recovery of the system and result in serious accident.

Ensure proper ventilation:

Do not block vents, intake or exhaust openings of the equipment. Blocking them may cause

mulfunctioning or overheating which may result in fire.

Prohibit excessive voltage or current:

Avoid applying excessive voltage and current across the input/output terminals by keeping them

within the specified ratings. Otherwise it may result in equipment damage.

Avoid noise interference:

Place I/O and data transmission signal cables away from the power cables and the devices that

generate magnetic or electromagnetic fields. Interference noise may cause the equipment to

malfunction.

Safety Precautions

2. Safety Precautions for Inspection and Maintenance

WARNING

Turn off power:

Turn off power before attaching or detaching modules or before connecting devices. Failure to do

so may result in electric shock or equipment fault.

Make sure that power is off:

Always check and make sure that the external power is turned off before installing or removing

modules. Bare metals appear on the back of external terminal block of the module. To avoid

electric shock, take precautions against touching them.

CAUTION

Clean filters:

If the equipment has filters, clean them periodically. If it has fans, clean grilles and screens also.

Clogged filter may cause the equipment to overheat, resulting in malfunction, failure or fire.

Avoid shock:

Do not drop, bump or give strong shocks to the equipment or modules to avoid fault. Shocks may

cause malfunction.

Discharge static electricity:

Before handling equipment or modules, discharge static electricity from your body by touching a

metal that is grounded. Static electricity may cause equipment to malfunction or fail.

Use a conductive sheet or bag to avoid static:

When cards and modules are taken out of base-unit, they should be placed on an electrically

conductive sheet (the bag that comes with spare module in it is made of conductive sheet), which

is put on a grounded work bench. Static electricity may damage electrical parts.

Wipe off dirt:

Wipe off dirt and dust from equipment or modules, using a soft cloth. In case the dirt is persistant,

wet a cloth and wring it dry, then use it on the dirt. Dirt on the parts may result in faulty actions and

operations.

Do not use paint thinner for cleaning:

Do not use benzene, paint thinner for cleaning equipment or modules. These chemicals will distort

or discolor panels and modules.

Safety Precautions

3. Safety Precautions for Part Replacement

WARNING

Ensure to stop fans:

When replacing fan unit, make sure to stop the fan by switching off the fan unit at the distribution

panel (or circuit breaker), before detaching the power cord. Failure to do so may result in electric

shock or injury due to the fan blades in motion.

CAUTION

Turn power off before replacing fuses:

Before replacing power fuses or alarm fuse, be sure to turn off power of the unit. Failure to do this

may result in electric shock or fire.

Use lithium batteries properly:

Do not insert lithium battery with the polarity in reverse. Do not short the battery nor charge it.

Otherwise it may explode.

Use right lithium battery for the module:

Do not use the lithium battery in one module for another. Ratings of lithium battery differs by the

module and the use of improper battery may damage the equipment.

4. Safety Precautions for Daily Use

WARNING

Check specifications:

Before using the equipment, make sure that the capacity, frequency, voltage and regulation of the

power supply meet the specifications of the equipment. In case they don't, the equipment may not

only work adequately but may suffer a breakdown or cause overheat that may result in fire.

Turn off power in the event of a problem:

If the temperature in or around the equipment becomes abnormally high or an unusual fault occurs

in the equipment, stop using it and turn off power, then contact your Toshiba representative. If left

alone, overheat may result in fire.

Safety Precautions

Avoid touching hot components:

Some components inside the modules become very hot after the power is turned on. To avoid

burns, do not touch them.

CAUTION

Do not touch components:

Do not touch pins, connectors or soldered surfaces in modules with any part of your body. Static

electricity may damage IC's or LSI's and cause equipment to fail. Also the pointed end of

component lead may hurt your body.

Do not disassemble the equipment:

Do not disassemble or modify the equipment or modules. Doing so may lesson equipment safety

or result in equipment malfunction or failure.

Handle cords and cables properly:

Do not force to pull, twist or bend cords and cables of power supply. Otherwise cables may break

or become hot.

Be careful of operations when the system is running:

Do not change function settings of switches on modules while the equipment is running. Otherwise

equipment may malfunction or fail.

Keep off metals:

Keep metals such as paper clips from going into the openings in the modules, units, and drives,

among others. Otherwise fire may result.

Safety Precautions

vii

5. Safety Precautions for Disposal

WARNING

Keep lithium batteries out of fire:

To avoid risk of explosion, do not throw lithium batteries into fire when you dispose of them.

CAUTION

Disposal of batteries:

Dispose lithium or Ni-Cad batteries according to the ordinance or regulations.

Full Compliance with the Following Precautions is a Must

A full compliance with the following precautions is a must in operating your equipment to

safeguard the safety of the operators and to maintain the equipment in the normal operating

condition:

(Note 1) Read the reference manual carefully before operating your equipment.

(Note 2) Avoid installing or storing your equipment in the following environment:

zDusty place

zPlace where corrosive gases generate, such as SO2and H2S.

zPlace subjected to vibration and shocks.

zPlace in a low- or a high-temperature environment deviating from the installation conditions specified

in this manual.

zA high-humidity place.

(Note 3) In case the ambient or internal temperature of the equipment rises abnormally high or

the equipment develops a failure, stop operating the equipment and turn the power off

the equipment. Contact the Toshiba service window in your area.

(Note 4) Do not open the equipment case or remodel the equipment.

(Note 5) Plug in or out the module after turning the power OFF.

(Note 6) The equipment taken out from the base unit must be placed on a conducting mattress

or conducting bag (bag containing a spare card) placed on a grounded desk.

Safety Precautions

viii

Limitations on Use

zThis product has not been developed or manufactured for use in a system containing equipment

which directly involves human life. (Please see NOTE 1.) This product must not be used for

such uses.

zIn case this product is to be used in a system (see NOTE 2) containing equipment which

involves human safety and may potentially cause serious impacts on the maintenance of public

functions, special considerations (see NOTE 3) will be needed for system operation,

maintenance and management. Consult the Toshiba sales representative in your area.

(Note 1) Equipment which directly involves human life is as follows:

zMedical equipment such as life sustaining equipment and equipment in surgical operation rooms.

(Note 2) Systems containing equipment which involves human safety and may potentially cause

serious impacts on the maintenance of public functions are as follows:

zReactor control systems in nuclear power plants, safety protection systems of nuclear power facilities

and other systems which are important in safety.

zOperation control systems of cargo collection and delivery transport systems and aviation control

systems.

(Note 3) Special considerations are the construction of a safety system to incorporate foolproof,

fail-safe, redundancy and other designs after fully consulting a TOSHIBA engineer.

Non-Liability Clauses

zToshiba will not be responsible for damage caused by a fire, earthquake or a third party, or by

use under abnormal conditions such as an accident, intention, error or abuse by the user.

zToshiba will not be responsible for incidental damage due to the use of or inability to use this

product, including losses of business profits, suspension of business and mutilation or erasure of

stored data.

zToshiba will not be responsible for damage caused due to a failure in complying with the content

of this reference manual.

zToshiba will not be responsible for damage caused by malfunctioning due to combination with

equipment connected.

zToshiba will not be responsible for damage caused by malfunctioning due to combination with an

application program created by the customer.

Andere Handbücher für TOSDIC-CIE DS

Inhaltsverzeichnis

Andere Toshiba Steuerungssystem Handbücher

Toshiba

Toshiba BMS-CT1280E Bedienungsanleitung

Toshiba

Toshiba BMS-TP5121PWE Bedienungsanleitung

Toshiba

Toshiba BMS-SM1280HTLE Bedienungsanleitung

Toshiba

Toshiba Carrier BMS-SM1280HTLUL Bedienungsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Bedienungsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Bedienungsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Bedienungsanleitung

Toshiba

Toshiba OIS Series Bedienungsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Bedienungsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Stücklistenhandbuch

Toshiba

Toshiba JOKC1 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-PS1 Bedienungsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Bedienungsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Bedienungsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Bedienungsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Bedienungsanleitung

Toshiba

Toshiba BMS-SM1280HTLE Bedienungsanleitung

Toshiba

Toshiba Carrier BMS-SM1280HTLUL Bedienungsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Betriebsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Bedienungsanleitung

Toshiba

Toshiba Combi control Bedienungsanleitung

Toshiba

Toshiba BMS-SM1280HTLE Bedienungsanleitung

Toshiba

Toshiba TOSDIC-CIE DS Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung

EMKO

EMKO TRANS-SYNCRO Bedienungsanleitung

Dover

Dover TWG GC ELEMENT II Programmierhandbuch