Toshiba RB-RXS34-E Bedienungsanleitung

1112150139

WIRELESS CONTROLLER

OPERATION MANUAL

For general public use

RB-RXS34-E

ENGLISHENGLISH

CONTENTS

1. PREPARATION BEFORE USE .....................................................................................1

2. AIR FLOW DIRECTION.................................................................................................1

3. REMOTE CONTROL.....................................................................................................1

4. COOLING / FAN ONLY OPERATION ...........................................................................1

5. AUTOMATIC OPERATION............................................................................................1

6. HEATING and 8°C OPERATION................................................................................1

7. DRY OPERATION..........................................................................................................1

8. MENU SETUP................................................................................................................2

9. MANUAL DEFORST OPERATION ...............................................................................5

10. DISPLAY LAMP BRIGHTNESS ADJUSTMENT...........................................................5

11. SELF CLEANING OPERATION

(COOL AND DRY OPERATION ONLY).........................................................................5

12. REMOTE CONTROL A-B SELECTION ........................................................................6

13. TEMPORARY OPERATION ..........................................................................................6

AUTOMATIC OPERATION

To automatically select cooling, heating, or fan only operation

1. Press

MODE

MOD

: Select Auto A.

2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.

3. Press FAN

FAN

: Select AUTO, LOW , LOW+ , MED ,

MED+ , HIGH or Quiet

1. Press

MODE

MOD

: Select Cool , or Fan only .

2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.

Fan Only: No temperature indication

3. Press FAN

FAN

: Select AUTO, LOW , LOW+ , MED ,

MED+ , HIGH or Quiet

DRY OPERATION

For dehumidiﬁcation, a moderate cooling performance is controlled

automatically.

1. Press

MODE

MOD

: Select Dry .

2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.

Note: DRY mode fan speed is set to Auto only.

HEATING and 8°C OPERATION

1. Press

MODE

MOD

: Select Heat .

2. Press

: Set the desired temperature. Min = 5°C, Max = 30°C.

* Temperature range 5-16°C is Heat mode with 8°C operation with less of

energy usage

3. Press FAN

FAN

Select AUTO, LOW , LOW+ , MED ,

MED+ , HIGH or Quiet

Note: During 8

°C mode active (temperature range 5-16°C), some operation

such as QUIET, Hi POWER, TIMER OFF cannot use.

AIR FLOW DIRECTION

Press FIX

FIX

: Move the

louver in the desired vertical

direction.

Press FIX

FIX

: Move the

louver in the desired horizontal

direction.

H.DA

Swing off

Vertical

(Up-Down)

Swing

Vertical and

Horizontal

Swing

Horizontal

(Left-Right)

Swing

HADA CARE

FLOW

SWING operation can be

selected from MENU button

MEN

●Vertical (Up-Down) swing

●Horizontal (Left-Right) swing

●HADA Care ﬂow

Note:

●Do not move the louver manually by hands or others.

●The louver may automation positioning by some operation mode.

Loading Batteries

1. Remove the slide cover.

2. Insert 2 new batteries (AAA type)

following the (+) and (–) positions.

Remote Control Reset

1. Remove the batteries.

2. Press .

3. Insert the batteries.

PREPARATION BEFORE USE

1REMOTE CONTROL

1Infrared signal emitter

2Start/Stop button

3Mode select button

4Temperature button

5Fan speed button

6Menu select button

7Set louver Up-Down button

Set louver Left-Right button

9Check button*

*Check button under battery cover

FIX

MODE

FAN MENU

FIX

FAN

MEN

MOD

COOLING / FAN ONLY OPERATION

‒1‒

MENU SETUP

For select more setting of Air conditioner such as Louver select ,Hi Power,

OFF Timer and other use MENU button MENU

MEN

FIX

MODE

FAN MENU

FIX

FAN

MEN

MOD

8.1 LOUVER SWING and HADA CARE FLOW OPERATION

Comfortable air ﬂow can select from feature.

Louver swing opearation:

●To distribute air ﬂow in both vertical and horizontal by swing the louver

automatically.

HADA care ﬂow operation:

●Air ﬂow upward to the ceiling, provide Indirect air ﬂow to body and

homogenize room temperature.

Note:

●During HADA CARE FLOW mode, FIX button cannot active.

Louver Swing and HADA Care Flow Operation Setting

1. Press MENU button for enter menu selection

MEN

°C

Blink

During triangle mark blink can select menu by press TEMP. button.

2. Enter Louver set by press MENU button again.

triangle mark will stop blink and setting feature will be blink instead.

°C

Blink

MEN

3. Select Louver swing or HADA CARE FLOW by press TEMP. button.

°C

H.DA

Swing

off

Vertical

(Up-Down)

Swing

Vertical and

Horizontal

Swing

Horizontal

(Left-Right)

Swing

HADA CARE FLOW

4. Conﬁrm selected feature by press MENU button again.

MEN

°C

When feature had selected will return to menu selection display triangle mark

will blink .

5. Leave from menu setting display by select exit and press menu button

MEN

°C

Leave from menu setting to normal display (no triangle and feature blink).

‒2‒

8.2 SILENT OPERATION (Outdoor Unit)

Keep outdoor unit operating silently to ensure either yourself or neighborhood

will have a tight sleep in nighttime. By this feature, the heating capacity will

be optimized to deliver such silent experience. The silent operation can be

selected from one of two purposes (Silent 1 and Silent 2).

There are three setting parameters: Standard level > Silent 1 > Silent 2

Silent 1:

●Though operating silently, the Heating (or Cooling) capacity is still prioritized

to ensure having sufﬁcient comfort inside the room.

●This setting is a perfect balance between the Heating (or Cooling) capacity

and the Sound level of outdoor unit.

Silent 2:

●Compromising the Heating (or Cooling) capacity to the Sound level in any

circumstance where the outdoor unit’s sound level is highly prioritized.

●This setting has a purpose to reduce the maximum sound level of outdoor

unit by 4 dB(A).

Note:

●While activating of Silent operation, inadequate heating (or cooling) capacity

may occur.

Silent Operation Setting

1. Press MENU button for enter menu selection

MEN

°C

Blink

During triangle mark blink can select menu by press TEMP. button.

°C

Blink both triangle and

feature mark Feature not

yet set

2. Enter SILENT set by press MENU button.

triangle mark will stop blink and setting feature will be blink instead.

°C

MEN

3. Select SILENT operation by press TEMP. button.

°C

SILENT#1 SILENT#2 None

4. Conﬁrm selected feature by press MENU button again.

MEN

°C

Blink only triangle

Feature already set

When feature had selected will return to menu selection display triangle mark

will blink

5. Leave from menu setting display by select EXIT.

MEN

°C

8.3 Hi POWER OPERATION Hi-P

To automatically control room temperature and airﬂow for faster cooling or

heating operation (except in DRY and FAN ONLY mode)

1. Press MENU button for enter menu setting and press TEMP. button to

select Hi POWER

MEN

°C

Blink both triangle and

feature mark Feature not

yet set

2. Conﬁrm selected feature by press MENU button again.

MEN

°C

Blink only triangle Feature

already set

3. Leave from menu setting display by select EXIT.

°C

8.4 ECO OPERATION

ECO

To automatically control room temperature to save energy

(except in DRY and FAN ONLY mode)

1. Press MENU button for enter menu setting and press TEMP. button to

select ECO

MEN

°C

Blink both triangle and

feature mark Feature not

yet set

2. Conﬁrm selected feature by press MENU button again.

MEN

°C

Blink only triangle Feature

already set

3. Leave from menu setting display by select EXIT.

MEN

°C

Note:

●Cooling operation; the set temperture will increase automatically

1 degree/hour for 2 hours (maximum 2 degrees increase).

For heating operation the set temperature will decrease.

‒3‒

8.5 FIREPLACE OPERATION

Keep indoor unit’s fan blowing continuously during thermo off, to circulate

heat from other sources over the room. There are three setting parameters:

Default setting > Fireplace 1 > Fireplace 2

Fireplace 1:

●During thermo off period, the indoor unit’s fan will continue to run by the

same speed, previously selected by end-user.

Fireplace 2:

●During thermo off period, the indoor unit’s fan will continue to run at

super-low speed, programmed from factory.

Fireplace Operation Setting

1. Press MENU button for enter menu setting and press TEMP. button to

select FIREPLACE

MEN

°C

Blink both triangle and

feature mark Feature not

yet set

2. Enter FIREPLACE set by press MENU button.

triangle mark will stop blink and setting feature will be blink instead.

MEN

°C

3. Select FIREPLACE operation by press TEMP. button.

°C

FIREPLACE 1 FIREPLACE 2 None

4. Conﬁrm selected feature by press MENU button again.

MEN

°C

Blink only triangle Feature

already set

When feature had selected will return to menu selection display triangle mark

will blink

5. Leave from menu setting display by select EXIT.

MEN

°C

Note:

●While Fireplace operation on heating mode, indoor unit fan always runs and

cold air breezing might be occurred.

●Fireplace will operate in Heating mode only.

8.6 TIMER OFF OPERATION

To set the timer OFF when the air conditioner is operating.

1. Press MENU button for enter menu setting and press TEMP. button to

select TIMER OFF.

MEN

°C

Blink both triangle and

feature mark Feature not

yet set

2. Enter TIMER set by press MENU button.

triangle mark will stop blink and setting feature will be blink instead.

MEN

3. Select TIMER OFF by press TEMP. button.

Can select TIMER OFF from 0.5 - 12hrs.

4. Conﬁrm TIMER OFF by press MENU button.

MEN

°C

Blink only triangle

Feature already set

5. Leave from menu setting display by select EXIT.

MEN

°C

Note:

●The setting will be saved for the next same operation.

Cancel TIMER OFF

6. During TIMER OFF already set (no.5) press MENU button and press

TEMP. button to select TIMER OFF.

MEN

°C

Blink only triangle

Feature already set

7. Press MENU button again will cancel TIMER OFF.

MEN

°C

Blink both triangle and feature

mark Feature not yet set

8. Leave from menu setting display by select EXIT.

MEN

°C

‒4‒

8.7 PLASMA ION OPERATION

PURE

Capture efﬁciency of ﬂoating impurities in the air is accelerated by plasma ion

contaminates such as bacteria, odor, smoke, dust and virus are caught and

deactivated by Plasma Ion.

1. Press MENU button for enter menu setting and press TEMP. button to

select PURE

MEN

°C

Blink both triangle and

feature mark Feature not

yet set

2. Conﬁrm selected feature by press MENU button again.

MEN

°C

Blink only triangle Feature

already set

3. Leave from menu setting display by select EXIT.

MEN

°C

Note:

●Plasma Ion operation dose not remove harmful substances from cigarette

smoke (carbon monoxide etc.). Open a window occasionally for ventilation.

8.8 POWER-SELECTION OPERATION

This function is used when the circuit breaker is shared with other electrical

appliances. It limits the maximum current and power consumption to 100%,

75%, or 50% and can be implemented by POWER-SELECTION. The lower

percentage, the higher saving and also longer compressor lifetime.

Notes :

●Due to the reason that POWER-SELECTION function limits the maximum

current, inadequate cooling or heating capacity may occur.

1. Press MENU button for enter menu setting and press TEMP. button to select

POWER-SEL

Blink only triangle

MEN

°C

2. Enter POWER-SEL setting by press MENU button again.

MEN

°C

3. Select POWER-SEL level by press TEMP. button.

°C

100% 75% 50%

4. Conﬁrm POWER-SEL level by press MENU button.

MEN

°C

5. Leave from menu setting display by select EXIT.

MEN

°C

MANUAL DEFORST OPERATION

To defrosting the heat exchanger of the outdoor unit during Heating operation

Press and hold MENU

MEN

: for 5 seconds , then remote control display will

show as picture 1for 2 seconds.

DISPLAY LAMP BRIGHTNESS ADJUSTMENT

To decrease the display lamp brightness or turn it off.

1. Press and hold FAN

FAN

for 3 seconds until brightness level ( , ,

or ) is shown on remote control LCD then release the button.

2. Press Rise or

Decrease

to adjust brightness in 4 levels.

Remote control

LCD Operation display Brightness

Lamp illuminates full brightness.

100%

Lamp illuminates 50% brightness.

50%

Lamp illuminates 50% brightness and the

operation lamp is turned off.

50%

All lamps are turned off.

All turned off

●

In the examples of and , the lamp illuminates for 5 seconds before going off.

SELF CLEANING OPERATION

(COOL AND DRY OPERATION ONLY)

To protect bad smell caused by the humidity in the indoor unit.

1. If the button is pressed once during “Cool” or “Dry” mode,

the fan will continue to run for other 30 minutes, then it will turn off

automatically. This will reduce the moisture in the indoor unit.

2. To stop the unit immediately, press the more 2 times within

30 seconds.

‒5‒

REMOTE CONTROL A-B SELECTION

To separate using of remote control for each indoor unit in case of 2 air

conditioners are installed nearly.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.

2. Point the remote control at the indoor unit.

3. Push and hold button on the back side of Remote Control “00” will be

shown on the display. (Picture 1)

4. Press

MODE

MOD

during pushing . “B” will show on the display and

“00” will disappear and the air conditioner will turn OFF. The Remote

Control B is memorized. (Picture 2)

Note: 1. Repeat above step to reset Remote Control to be A.

2. Remote Control A has not “A” display.

3. Default setting of Remote Control from factory is A.

TEMPORARY OPERATION

In case of the misplaced or discharged remote control

●Pressing the RESET button, the unit can start

or stop without using the remote control.

●Operation mode is set on AUTOMATIC

operation, preset temperature is 24°C and fan

operation is automatic speed.

OPERATION / RESET Button

‒6‒

Inhaltsverzeichnis

Andere Toshiba Controller Handbücher

Toshiba

Toshiba TD Series Bedienungsanleitung

Toshiba

Toshiba LC531 Series Bedienungsanleitung

Toshiba

Toshiba OIS PLUS Series Bedienungsanleitung

Toshiba

Toshiba TCR15AG Series Bedienungsanleitung

Toshiba

Toshiba TE2 Series Bedienungsanleitung

Toshiba

Toshiba 2000 Bedienungsanleitung

Toshiba

Toshiba 2000 Bedienungsanleitung

Toshiba

Toshiba TS3000 Series Bedienungsanleitung

Toshiba

Toshiba TSL3000 Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba EX500 Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba TMP87CM24AF Gebrauchsanweisung

Toshiba

Toshiba GX9 ASD Bedienungsanleitung

Toshiba

Toshiba TS3000 Series Bedienungsanleitung

Toshiba

Toshiba Vm Series Bedienungsanleitung

Toshiba

Toshiba TS3000 Series Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba TSL3000 Gebrauchs- und Pflegehandbuch

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba RBC-MTSC1 Bedienungsanleitung

Toshiba

Toshiba Network Device OIS120 Bedienungsanleitung

Toshiba

Toshiba S2E21 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch