Toshiba V Series Bedienungsanleitung

6F8C0903

Integrated Controller V Series

model 3000 DeviceNet

Module Manual (DN311/DN311A)

Mar 26, 2001

TOSHIBA CORPORATION

Important Information

No patent liability is assumed by TOSHIBA Corporation with respect to use of information, illustrations,

circuits, equipment or examples of application in this publication.

TOSHIBA Corporation reserves the right to make changes and improvements to this publication and/or

related products at any time without notice. No obligation shall be incurred other than as noted in this

publication.

This publication is copyrighted and contains proprietary material. No part of this book may be reproduced,

stored in a retrieval system, or transmitted, in any form or by any means — electrical, mechanical,

photocopying, recording, or otherwise — without obtaining prior written permission from TOSHIBA

Corporation.

PROSEC, TOSLINE and TOSDIC are trademarks or registered trademarks of TOSHIBA Corporation.

IBM is a registered trademark of International Business Machines Corporation.

Microsoft, MS-DOS, Windows and Windows NT are registered trademarks of Microsoft Corporation in the

U.S.A. and other countries.

Ethernet is a registered trademark of Xerox Corporation.

DeviceNet is a trademark of the Open DeviceNet Vender Association, Inc.

6F8C0903 i

Safety Precautions

This manual contains important information for the operator to operate this product safely and correctly

and avoid bodily injury and property damage.

Grasp the meanings of the following marks and their descriptions before reading this manual.

Hazard Classifications

Note: 1. Serious injury means loss of sight, injury, burns (high temperature, low temperature), electrical

shock, fracture, or intoxication which leaves aftereffects or requires hospitalization or need to

go to the hospital for a long time.

2. Injury means hurt, burn, or electrical shock which does not require hospitalization or going to

the hospital for a long time.

3. Property damage means extended breakdown of assets and materials.

Notation of Markings

Note: The description of forbiddance, mandatory, and caution marks are subject to change, depending

on the labels on the main unit.

WARNING Indicates a potentially hazardous situation which, if not avoided,

could result in serious injury or death.

CAUTION Indicates a potentially hazardous situation which, if not a avoided,

can result in minor or moderate injury, or property damage. It can

also be used to alert against unsafe practices.

Prohibited Indicates a "may not" mark.

The concrete forbiddance is indicated with a pictograph or wording.

Mandatory Indicate a mandatory action that you should never fail to do.

The concrete content is indicated inside or near the circle with a

pictograph or wording.

Caution Indicates a caution.

The concrete content is indicated inside or near the triangle.

ii model 3000 DeviceNet Module Manual (DN311/DN311A)

WARNING

CAUTION

1. Checking the Warning Labels on the Main Unit

Make sure warning markings are attached on the main unit.

If any of them are missing or the wording is illegible, contact Toshiba's Service Department.

2. Precautions on Installation

Be sure to ground the equipment.

Operation without grounding may cause

accidental fire or shock.

Mandatory

Avoid the following locations when

installing or storaging the equipment.

•Locations where there is dust, salinity, or ion

particles

•Locations where there are corrosive gases

(SO2, H2S) or flammable gases

•Locations where vibration or shock occurs

beyond the allowance

•Locations where there is condensation due

to sharp temperature variations

•Locations where the ambient temperature

exceeds the allowance range

•Locations where the relative humidity

exceeds the allowance range

•Locations where the equipment is exposed

to direct sunlight

•Locations where strong electric radiation or

magnetic field is generated

Improper the installation or writing of the

system can cause not only insufficient

performance but also malfunction and

failure of the equipment

Mandatory

1. Be sure to switch power off before installing

cables.

Installing cables without switching power off

can cause electric shock.

2. For cabling the S controller power module,

either use a crimp terminal with sheath, or

cover the cable end with tape to keep the

conductors unexposed.

Carefully handle the terminal block cover

not to drop or break it. Put it back on the

terminal block securely after wiring it.

Exposed conductors can cause electric

shock.

3. Be sure to ground the product. Failure to

observe it can cause electric shock or

malfunction.

Mandatory

6F8C0903 iii

Mandatory

Install the equipment at a place where

maintenance and inspection are easy to do.

Otherwise, recovery from failure may take much

more time, leading to a serious accidents.

Mandatory

1. Before mounting or removing the DN311, be

sure to switch power off (S controller power

and network power). Failure to do so can

cause electric shock or fire.

2. Keep the DN311 free of wire fragments and

other foreign matter to prevent fire, module

trouble, and malfunction.

3. Secure the joints of the connectors and

cables and the DN311 mounted in the base

unit with stoppers or screws to prevent them

from slipping out of place or getting

unsteady.

If they are not adequately secured, vibration,

etc. can cause trouble or malfunction.

Mandatory

Cabling must be done by qualified

personnel. The wrong cabling can cause

fire, module trouble or electric shock.

Mandatory

Ask a qualified service agent for DeviceNet

cabling because it requires safety and anti-

noise measures.

For the specifications of the installation

procedures, refer to DeviceNet Volume I.

Be sure to mount the DN311 in the base

unit because it is for the V Series model

3000. Do not use it alone or for other

applications.

Failure to observe this can cause electric

shock, injuries or module trouble.

Forbidden

Mandatory

1. Be sure to mount the DN311 in the base unit

because it is exclusive to the model 3000.

Do not use it alone or for other applications.

Failure to observe this can cause electric

shock, injuries or module trouble.

2. Be sure to keep power switched off when

mounting or removing the DN311.

Failure to do so can cause electric shock,

malfunction or module trouble.

3. Keep the DN311 free of wire fragments and

other foreign matter to prevent fire, module

trouble, and malfunction.

4. Secure the joints of the connectors and

cables and the DN311 mounted in the base

unit with stoppers or screws to prevent them

from slipping out of place or getting

unsteady.

If they are not adequately secured, vibration,

etc. can cause trouble or malfunction.

Mandatory

Basic Precautions for Network Installation

1. Ask a qualified service agent for DeviceNet

cabling because it requires safety and anti-

noise measures.

For the specifications of the installation

procedures, refer to DeviceNet Volume I.

2. It is recommended that you ask a service

agent specialized in safety measures and

standards for cable installation.

3. Avoid installing DeviceNet network

components in a noisy environment. In

cases where it is necessary to do so, be

sure to take the following measures against

noise.

Do not cover the hole of the equipment, and the

ventilator/air inlet of the system.

Otherwise, overheating, etc. can cause fire

or malfunction.

Forbidden

iv model 3000 DeviceNet Module Manual (DN311/DN311A)

WARNING

1. Do not connect the DeviceNet cables to, or

disconnect them from, network connectors

while the network is in operation.

The wrong connection or a network

shortcircuit, for example, may disable

communication with other nodes.

2. Do not connect a network connector to, or

disconnect it from, a device connector on

the front panel of the DN311 while the S

controller power is on.}

Failure to observe this can cause DN311

trouble or malfunction.

3. Network connectors cannot be connected

to, or disconnected from, device connectors

in the wrong direction for reasons of their

structure. Do not try to forcibly push them

in.

Otherwise, the network connectors and

device connectors will be damaged.

4. Install the cables, exercise care not to

pulling them too tight or bending them.

Do not place heavy objects on the cables.

This is important to prevent the cables from

breaking.

Forbidden

1. Do not connect a network connector to, or

disconnect it from, a device connector on

the front panel of the DN311 while the S

controller power is on.

Failure to observe this can cause DN311

trouble or malfunction.

2. Network connectors cannot be connected

to, or disconnected from, device connectors

in the wrong direction. Do not try to forcibly

push them in.

Otherwise, the network connectors and

device connectors will be damaged.

Forbidden

3. Safety Precautions on Maintenance and inspection

Turn off power removing or connecting any

modules, boards, or devices.

Otherwise, it can cause electrical shock, or

machine damage.

Mandatory

Turn off power removing any modules after

installing.

Otherwise, exposed conductive parts of wire

or on the rear of terminal blocks can cause

electrical shock.

Mandatory

6F8C0903 v

CAUTION

Be careful not to hit or fall off the equipment by

accident.

Excess shock can cause failure.

Touch a grounded metal part to discharge the

static electricity on your body before touching

the equipment.

Otherwise, charged static electricity on your

body can cause malfunction or failure.

Mandatory

Forbidden

Use soft cloth to clean the equipment.

Use water-dipped and squeezed cloth to

clean it if dirty.

Leaving the equipment dirty can cause

mistaken or malfunction.

Mandatory

Do not apply benzene and thinner when clean-

ing the equipment.

Otherwise, it can cause deformity or discolora-

tion the panel or case of the equipment.

Place any modules or boards removed from

the unit on a conductive mat or conductive bag

(containing a spare board, etc.) on an

grounded desk.

Otherwise, static electricity can damage

components of the module.

Mandatory

Forbidden

vi model 3000 DeviceNet Module Manual (DN311/DN311A)

WARNING CAUTION

WARNING

4. Precautions During Parts Replacement

Turn off power of the equipment before

replacing the power fuse or warning fuse.

Otherwise, it can cause electrical shock or fire.

Mandatory

1. A parameter setting request (from a slave

device) sets slave device parameters in the

non-volatile memory of the DN311. Unless

the slave device configuration is changed, it

is not necessary to execute this request

each time power is switched on.

If the requested slave device parameters

are identical with those in the non-volatile

memory, no parameter setting processing

will take place.

2. To change the slave device configuration,

delete the slave device parameters in the

non-volatile memory, and set new slave

device parameters.

3. Slave device parameters can be set in the

non-volatile memory of the DN311 up to 300

times.

Mandatory

5. Precautions During Daily Use

Apply power of the specified ratings (voltage

fluctuation range, frequency, output rating,

etc.) in User's manual.

Otherwise, it can cause malfunction, machine

damage or fire due to overheat.

Mandatory

Turn off power immediately if the ambient

temperature or internal temperature exceeds

beyond normal range or if failure is occurred

in the equipment.

Contact Toshiba for repairing.

Operation under such situation can cause fire

or electrical shock.

Mandatory

6F8C0903 vii

CAUTION

WARNING CAUTION

Do not touch any components, terminals,

connectors, or printed circuit boards in the

module.

Otherwise, it can cause the IC or LSI or the

like to be broken by static electricity, resulting

in failure or malfunction.

Also, the edge of components can cause

injury.

Forbidden

Do not disassemble or modify the equipment.

Otherwise, it can cause malfunction or failure.

Forbidden

Do not forcibly bend or pull or distort the power

cord and other cables. Otherwise, they can be

cut off or cause overheat.

Forbidden

Do not enter wire scrapes or other foreign

debris into the equipment.

Also, do not insert metal parts into them.

They can cause fire or accidents.

Forbidden

6. Safety Precautions on Disposal

Do not throw lithium batteries into fire.

Otherwise, they can explode.

Forbidden

Observe local regulations for disposal of the

lithium batteries or the product (Base unit

and modules).

Mandatory

In disposing of the lithium battery or Ni-Cd

battery, observe the rules and regulations of

the local administration.

Mandatory

viii model 3000 DeviceNet Module Manual (DN311/DN311A)

CAUTION

7. Precautions for Use of The Equipment

1. Do not change node addresses while the S

controller power is on. Otherwise, a node

address setting error will occur. Particularly,

do not change the communication rate

while transmission is under way to a slave

device. To reset, set the DIP switches

correctly, then either issue a reset request

or switch power on again.

Mandatory

1. Do not switch the network power off while

the network is in communication.

Switching it off will interrupt the

communication of the network as a whole

and set one of the nodes in a busoff state.

Forbidden

1. Prepare programs after fully understanding

the manual.

The sample programs are basic examples

and must be adequately studied for

applicability to an actual system.

Mandatory

1. The DIP switch OSEN must be kept in the

OFF position. When it is set to the ON

position, it may cause trouble or

malfunction.

2. Set the same communication rate for all the

nodes connected to the network. Different

communication rates among the nodes will

result in a slave device error or DN311 error,

disabling communication to restart. To set a

slave device communication rate, read the

pertinent manuals.

3. Do not change the communication rate

while the S controller power is on.

Otherwise, a communication rate setting

error will occur. Particularly, do not change

the communication rate while transmission

is under way to a slave device. To reset, set

the DIP switches correctly, then either issue

a reset request or switch power on again.

Mandatory

Andere Handbücher für V Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Controller Handbücher

Toshiba

Toshiba EX500 Bedienungsanleitung

Toshiba

Toshiba nv Series Betriebsanleitung

Toshiba

Toshiba RBC-AWSU52-UL Bedienungsanleitung

Toshiba

Toshiba JKSSS Series Bedienungsanleitung

Toshiba

Toshiba TS2000 Bedienungsanleitung

Toshiba

Toshiba Preliminary TB6560AHQ Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba Prosec T-Series Bedienungsanleitung

Toshiba

Toshiba OIS50 Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba TCB-SC640U Bedienungsanleitung

Toshiba

Toshiba TXZ+ Series Bedienungsanleitung

Toshiba

Toshiba 2000 Bedienungsanleitung

Toshiba

Toshiba RBC-AIP2 Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba TS3000 Series Bedienungsanleitung

Toshiba

Toshiba TS2000 Bedienungsanleitung

Toshiba

Toshiba TMP87CM24AF Gebrauchsanweisung

Toshiba

Toshiba PROSEC T1-16S Bedienungsanleitung

Toshiba

Toshiba TCB-TSC640-PY Bedienungsanleitung

Toshiba

Toshiba JK Series Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba P9 ASD Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch