Toshiba TS1000 Installations- und Betriebshandbuch

STE 71282-2

STARTUP MANUAL

Notice

• Make sure that this instruction manual is delivered to the

final user of Toshiba Machine's industrial robot.

• Before operating the industrial robot, read through and

completely understand this manual.

• After reading through this manual, keep it nearby for future

reference.

TOSHIBA MACHINE CO., LTD.

TOKYO, JAPAN

– 1 – STE 71282

STARTUP MANUAL

No part of this document may be reproduced in any form without obtaining prior written

permission from Toshiba Machine Co., Ltd.

The information contained in this manual is subject to change without prior notice to

effect improvements.

– 2 – STE 71282

STARTUP MANUAL

Preface

This manual describes the procedures covering from power ON of the robot after

installation to robot operation by manual guide and by programs.

Before reading this manual, install the robot according to the Safety Manual and

Installation & Transport Manual.

When you use the TH series robot for the first time, be sure to read through this manual.

Structure of TH series robot and TS1000 controller instruction manuals:

These instruction manuals were published in parts according to the application and

purpose, and the name and outline of each manual are as follows:

[Safety Manual]

This manual contains the important information to use the robot safety and correctly.

Be sure to read through and understand this manual before operating the robot.

Also, strictly observe the descriptions made there.

[Installation & Transport Manual]

This manual describes the transport, unpacking and installation of the robot and

controller. Be sure to read through this manual before unpacking the shipment

containing the robot.

[Operator’s Manual]

This manual deals with the TS1000 controller operating procedures. Read through

this manual before operating the robot, and refer to it as necessary.

[Robot Language Manual]

This manual refers to the robot language called "SCOL". When you have to create

a program based on this language, read through the manual.

[Interface Manual]

This manual describes the external signals for the robot. Concerning the interface

conditions between the robot and peripheral equipment, specifications, timing, etc.,

refer to the manual when necessary.

[Maintenance Manual]

This manual deals with the daily and regular inspections to be made on the robot

and controller. Read through this manual to use the robot safely over long years to

come.

– 3 – STE 71282

STARTUP MANUAL

[Communication Manual]

This manual describes the serial communication between the robot controller and

other equipment. Refer to this manual when connecting the robot controller with a

host computer, optical sensor, etc., via a serial cable.

– 4 – STE 71282

STARTUP MANUAL

Cautions on Safety

This manual contains the important information on the robot and controller to prevent

injury to the operators and persons nearby, to prevent damage to assets and to assure

correct use.

Make sure that the following details (indications and symbols) are well understood

before reading this manual. Always observe the information that is noted.

[Explanation of indications]

Indication Meaning of indication

DANGER

This means that "incorrect handling will lead to fatalities

or serious injuries."

CAUTION

This means that "incorrect handling may lead to

personal injuries *1) or physical damage *2).

*1) Injuries refer to injuries, burns and electric shocks, etc., which do not require

hospitalization or long-term medical treatment.

*2) Physical damage refers to damages due to destruction of assets or resources.

[Explanation of symbols]

Symbol Meaning of symbol

This means that the action is prohibited (must not be done).

Details of the actions actually prohibited are indicated with

pictures or words in or near the symbol.

This means that the action is mandatory (must be done).

Details of the actions that must be done are indicated with

pictures or words in or near the symbol.

This means danger.

Details of the actual danger are indicated with pictures or words in

or near the symbol.

This means caution.

Details of the actual caution are indicated with pictures or words in

or near the symbol.

– 5 – STE 71282

STARTUP MANUAL

[Operation]

DANGER

Prohibited

• During operation, NEVER enter the dangerous area of the robot.

Otherwise, you will be injured seriously.

• DO NOT leave in the working range any machinery or materials

which will hinder the operation. If the equipment went wrong, a

person nearby will be injured or involved in an accident.

• Anyone other than the operator MUST NOT approach the

equipment. Should he negligently touch the dangerous part of

the equipment, he will get injured or involved in a serious

accident.

• NEVER perform an inappropriate operation which is not described

in the instruction manual. Otherwise, the equipment will start by

mistake, resulting in personal injury or serious accident.

Danger

• If you feel even a little that you are exposed to danger or that the

equipment works abnormally, press the EMERGENCY stop

pushbutton switch to stop the equipment. If the equipment is

used as it is, you will be injured or involved in a serious accident.

When this happens, ask our after-sale service agent for repair.

• During operation, be sure to close the equipment cover. Should

the cover be opened during operation, you will be struck by an

electric shock or get injured.

• Only a well-trained and qualified person is allowed to perform the

operation. Should the equipment be operated improperly, it will

start by mistake, causing a personal injury or serious accident.

• If the equipment has malfunctioned, turn the power off, identify

and remove the cause of the abnormality, maintain the peripheral

equipment and completely restore the malfunctioned equipment.

Then start the equipment at a slow speed. If the equipment

starts, leaving the abnormality, you will be involved in a serious

accident.

– 6 – STE 71282

STARTUP MANUAL

CAUTION

Prohibited

• DO NOT change the data of the system structure file. Otherwise,

the robot will move abnormally, resulting in damage or an

accident.

Mandatory

• In principle, teaching operation should be performed outside the

dangerous area of the robot. If it should be performed inevitably

within the dangerous area, strictly observe the following matters.

(1) The teaching operation should always be performed by two (2)

persons. One person performs the job and the other person

watches outside the dangerous area. Also, both persons

should try to prevent mis-operation with each other.

(2) The operator should do the job in an attitude ready to press

the EMERGENCY stop pushbutton switch at any time. Also,

he should perform the job at a position from which he can

evacuate immediately at the time of an emergency after

confirming the robot working range and shields nearby.

(3) The supervisor should keep watch on the job at a position

where he can see the entire robot system and operate the

EMERGENCY stop pushbutton switch at the time of an

emergency. Also, he should keep anyone from entering the

dangerous area. Unless the operator or other person follows

the instructions of the supervisor, an accident will be caused.

• If an abnormality has generated or the POWER LED lamp on the

control panel remains off after the main power switch of the

equipment was turned on, turn off the main power immediately

and confirm the wiring. Otherwise, you will be struck by an

electric shock or a fire will break out.

• Unless the robot operates toward a designated direction at

manual guide, turn off the servo power. Otherwise, the robot will

be damaged or you will be involved in an accident. When this

happens, call us at the after-sale service agent.

• Pushbutton operations on the operation panel and teach pendant

should be confirmed visually. Otherwise, you will be involved in

an accident due to mis-operation.

• After the power is turned on, be sure to reset a program to start

an automatic operation. If the program is executed continuously,

the robot will interfere with the peripheral equipment, resulting in

damages or accidents.

– 7 – STE 71282

STARTUP MANUAL

CAUTION

Mandatory

• Before operating the equipment, perform the following inspection.

(1) Make sure that visual appearance of the robot, controller,

peripheral equipment and cables is in the good condition.

(2) Make sure that no obstacle stands in or near the working

range of the robot and peripheral equipment.

(3) Make sure that the emergency stop and other safety devices

operate properly.

(4) Make sure that no abnormal noise or vibration is involved in

the robot operation.

If the above prior inspection is skipped, the equipment will be

damaged or you will be involved in an accident.

Caution

• The speed of test operations is initially set at 25 % of the

maximum robot speed.

• The speed of automatic operation is initially set at 100 % of the

maximum robot speed.

– 8 – STE 71282

STARTUP MANUAL

Table of Contents

Page

1. Before Power ON............................................................................................ 9

1.1 Control Panel ....................................................................................... 11

1.2 Teach Pendant..................................................................................... 12

2. Power ON....................................................................................................... 13

2.1 Power ON............................................................................................. 13

2.2 Emergency Stop................................................................................... 14

2.3 Servo ON ............................................................................................. 15

2.4 Main Display......................................................................................... 16

2.5 Power OFF........................................................................................... 18

3. Manual Operation ........................................................................................... 19

3.1 Enable Switch ...................................................................................... 19

3.2 Joint Guide........................................................................................... 20

3.3 Guide in Cartesian Coordinate System................................................ 23

4. Programming .................................................................................................. 25

4.1 Starting Editor ...................................................................................... 25

4.2 Entering Program................................................................................. 29

4.3 Entering Data (Teach Points)............................................................... 30

4.4 Quitting Editor ...................................................................................... 34

5. Starting Program............................................................................................. 35

5.1 Selecting Program................................................................................ 35

5.2 Test Operation ..................................................................................... 38

5.3 Internal Automatic Operation................................................................ 43

6. Input/Output Control........................................................................................ 44

6.1 User's Function Switches..................................................................... 44

6.2 7-Segment User Display ...................................................................... 44

6.3 I/O Control Program............................................................................. 45

– 9 – STE 71282

STARTUP MANUAL

1. Before Power ON

Before turning the power on, confirm the following matters, referring to the

Installation & Transport Manual.

Is the robot secured?

Four (4) M8 hexagon socket head cap screws

Is the power supply connected?

Single phase, 170 ~ 250 V AC power supply

Robot Controller

TEACHING

INTERNAL

EXT. SIGNAL

EXT. HOST

POWER

EMERGENCY

LINE

USER

ALARM

SERVO

ON SERVO

OFF

RUN STOP

UF1

UF2

ALARM

RESET

SELECT

MODE

CYCLE

Inhaltsverzeichnis

Andere Toshiba Controller Handbücher

Toshiba

Toshiba BMS-IFBN1281U-E Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba EX500 Bedienungsanleitung

Toshiba

Toshiba JK-UC1 Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba TSL3000 Bedienungsanleitung

Toshiba

Toshiba 40 Plus Bedienungsanleitung

Toshiba

Toshiba T300MVi MEDIUM VOLTAGE Bedienungsanleitung

Toshiba

Toshiba TS3000 Series Bedienungsanleitung

Toshiba

Toshiba Programmable Controller PROSEC T3 Bedienungsanleitung

Toshiba

Toshiba Q9 Plus ASD Bedienungsanleitung

Toshiba

Toshiba TCB-SC640U-UL Bedienungsanleitung

Toshiba

Toshiba RBC-AWSU52-E Bedienungsanleitung

Toshiba

Toshiba nv-pack Bedienungsanleitung

Toshiba

Toshiba RBC-MTSC2 Bedienungsanleitung

Toshiba

Toshiba Vm Series Bedienungsanleitung

Toshiba

Toshiba CONNECT Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba DeviceNet nv Series Bedienungsanleitung

Toshiba

Toshiba TDP T3 Bedienungsanleitung

Toshiba

Toshiba TS2000 Bedienungsanleitung

Toshiba

Toshiba BMS-CT5121E Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch