Toshiba T300MVi MEDIUM VOLTAGE Bedienungsanleitung

T300MVi

ADJUSTABLE SPEED MOTOR DRIVE

INSTRUCTION MANUAL

TOSHIBA INTERNATIONAL CORPORATION

Document Number: IF08CZ00

June, 2009

MEDIUM VOLTAGE

- ii -

TOSHIBA INTERNATIONAL CORPORATION

13131 WEST LITTLE YORK

HOUSTON, TEXAS 77041

Tel: 1-713-466-0277

1-800-231-1412

Printed in U.S.A.

- iii -

Important Notice

The instructions contained in this manual are not intended to cover all details or variations in

equipment types, nor may it provide for every possible contingency concerning the installation, operation, or

maintenance of this equipment. Should additional information be required contact your Toshiba

representative.

The contents of this manual shall not become a part of or modify any prior or existing agreement,

commitment, or relationship. The sales contract contains the entire obligation of Toshiba International

Corporation. The warranty contained in the contract between the parties is the sole warranty of Toshiba

International Corporation and any statements contained herein do not create new warranties or modify the

existing warranty.

Any electrical or mechanical modifications to this equipment without prior written consent of

Toshiba International Corporation will void all warranties and may void the UL/CUL listing or other

safety certifications. Unauthorized modifications may also result in a safety hazard or equipment

damage.

Misuse of this equipment could result in injury and equipment damage. In no event will

Toshiba Corporation be responsible or liable for either indirect or consequential damage or injury

that may result from the misuse of this equipment.

TOSHIBA INTERNATIONAL CORPORATION

Adjustable Speed Drive

Pleasecomplete the Warranty Card supplied with the ASD and return it to Toshiba by prepaid mail. This will

activate the 12 month warranty from the date of installation; but, shall not exceed 18 months from the date of

purchase.

Complete the followinginformation about the drive andretain it for your records.

Model Number:

Serial Number:

Project Number (if applicable):

Date of Installation:

Inspected By:

Name of Application:

- iv -

Manual’s Purpose and Scope

This manual provides information on how to safely install, operate, and maintain your TIC power

electronics product. This manual includes a section of general safety instructions that describes the warning

labels and symbols that are used throughout the manual. Read the manual completely before installing,

operating, or performing maintenance on this equipment.

This manual and the accompanying drawings should be considered a permanent part of the

equipment and should be readily available for reference and review. Dimensions shown in the manual are in

metric and/or the English equivalent.

Toshiba International Corporation reserves the right, without prior notice, to update information,

make product changes, or to discontinue any product or service identified in this publication.

TOSHIBA is a registered trademark of the Toshiba Corporation. All other product or trade

references appearing in this manual are registered trademarks of their respective owners.

Toshiba International Corporation (TIC) shall not be liable for direct, indirect, special, or

consequential damages resulting from the use of the information contained within this manual.

This manual is copyrighted. No part of this manual may be photocopied or reproduced in any form

without the prior written consent of Toshiba International Corporation.

Printed in the U.S.A.

Contacting Toshiba’s Customer Support Center

Toshiba’s Customer Support Center can be contacted to obtain help in resolving any Adjustable

Speed Drive system problem that you may experience or to provide application information.

The center is open from 8 a.m. to 5 p.m. (CST), Monday through Friday. The Support Center’s toll

free number is US (800) 231-1412/Fax (713) 466-8773 — Canada (800) 527-1204.

You may also contact Toshiba by writing to:

Toshiba International Corporation

13131 West Little York Road

Houston, Texas 77041-9990

Attn: ASD Product Manager.

For further information on Toshiba’s products and services, please visit our website at

www.toshiba.com/ind.

- v -

General Safety Instructions

DO NOT attempt to install, operate, maintain or dispose of this equipment until you have read and

understood all of the product safety information and directions that are contained in this manual.

Safety Alert Symbol

The Safety Alert Symbol indicates that a potential personal injury hazard exists. The symbol is

comprised of an equilateral triangle enclosing an exclamation mark.

Signal Words

Listed below are the signal words that are used throughout this manual followed by their

descriptions and associated symbols. When the words DANGER, WARNING and CAUTION are used in

this manual they will be followed by important safety information that must be adhered to.

The word DANGER preceded by the safety alert symbol indicates that an imminently hazardous

situation exists that, if not avoided, will result in death or serious injury to personnel.

The word WARNING preceded by the safety alert symbol indicates that a potentially hazardous

situation exists that, if not avoided, could result in death or serious injury to personnel.

The word CAUTION preceded by the safety alert symbol indicates that a potentially hazardous

situation exists which, if not avoided, may result in minor or moderate injury.

The word CAUTION without the safety alert symbol indicates a potentially hazardous situation

exists which, if not avoided, may result in equipment and property damage.

DANGER

WARNING

CAUTION

- vi -

Special Symbols

To identify special hazards, other symbols may appear in conjunction with the DANGER,

WARNING and CAUTION signal words. These symbols indicate areas that require special and/or strict

adherence to the procedures to prevent serious injury to personnel or death.

Electrical Hazard Symbol

A symbol which indicates a hazard of injury from

electrical shock or burn. It is comprised of an equilateral

triangle enclosing a lightning bolt.

Explosion Hazard Symbol

A symbol which indicates a hazard of injury from

exploding parts. It is comprised of an equilateral triangle

enclosing an explosion image.

- vii -

Equipment Labels (Safety, Rating, Information)

DO NOT attempt to install, operate, perform maintenance, or dispose of this equipment until you

have read and understood all of the product labels and user directions that are contained in this manual.

Shown below are examples of safety labels that may be found attached to the equipment. DO NOT

remove or cover any of the labels. If the labels are damaged or if additional labels are required, contact your

Toshiba representative for additional labels.

Labels attached to the equipment are there to provide useful information or to indicate an

imminently hazardous situation that may result in serious injury, severe property and equipment damage, or

death if the instructions are not followed.

SAFETY labels that will be found on the equipment are shown below:

- viii -

RATING labels that will be found on the equipment are shown below:

Note:

The above labels are shown blank. The labels affixed to the equipment will be filled in with rating data

specific to the actual unit(s) furnished. Complete rating data is also provided on the rating sheet included

in the supplementary drawing packet. Ensure that all rating data matches the power system and the

driven load connected to the equipment.

Input Controller Rating Label

Note: If no input controller is

supplied, this label will not be

present. Refer to label on upstream

equipment for rating data.

Adjustable Speed Drive Rating Label

Inverter Power Module Rating Label

- ix -

INFORMATION labels that will be found on the equipment are shown below:

USC

LISTED

Torque Label

Service Label

UL Label

(for UL Listed drives)

CE Label

(for drives designed

for use in the

Euro

ean Union

)

- x -

Qualified Personnel

Installation, operation, and maintenance shall be performed by Qualified Personnel Only. A

Qualified Person is one that has the skills and knowledge relating to the construction, installation,

operation, and maintenance of the electrical equipment and has received safety training on the hazards

involved. In the U.S., refer to the latest edition of NFPA 70E for additional safety requirements. Outside the

U.S., follow all applicable national and local safety practices.

Qualified Personnel shall:

•Have read the entire operation manual.

•Be familiar with the construction and function of the ASD, the equipment being driven, and the

hazards involved.

•Able to recognize and properly address hazards associated with the application of motor-driven

equipment.

•Be trained and authorized to safely energize, de-energize, ground, lockout/tagout circuits and

equipment, and clear faults in accordance with established safety practices.

•Be trained in the proper care and use of protective equipment such as safety shoes, rubber

gloves, hard hats, safety glasses, face shields, flash clothing, etc., in accordance with established

safety practices.

•Be trained in rendering first aid.

For further information on workplace safety in the U.S. visit www.osha.gov.Outside the U.S.,

refer to your existing plant safety regulations.

Equipment Inspection

•Upon receipt of the equipment inspect the packaging and equipment for shipping damage.

•Carefully unpack the equipment and check for parts that were damaged from shipping, missing

parts, or concealed damage. If any discrepancies are discovered, it should be noted with the carrier

prior to accepting the shipment, if possible. File a claim with the carrier if necessary and

immediately notify your Toshiba representative.

•DO NOT install or energize equipment that has been damaged. Damaged equipment may fail

during operation resulting in further equipment damage or personal injury.

•Check to see that the rated capacity and the model number specified on the nameplate conform

to the order specifications.

•Modification of this equipment is dangerous and must not be performed except by factory trained

representatives. When modifications are required contact your Toshiba representative.

•Inspections may be required before and after moving installed equipment.

•Keep the equipment in an upright position as indicated on the shipping carton.

•Contact your Toshiba representative for assistance if required.

Andere Handbücher für T300MVi MEDIUM VOLTAGE

Inhaltsverzeichnis

Andere Toshiba Controller Handbücher

Toshiba

Toshiba TSL3000 Gebrauchs- und Pflegehandbuch

Toshiba

Toshiba RBC-ASC11E Bedienungsanleitung

Toshiba

Toshiba TDP T3 Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba TE Series Bedienungsanleitung

Toshiba

Toshiba TS3000 Series Bedienungsanleitung

Toshiba

Toshiba BMS-CT1280E Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba JK Series Bedienungsanleitung

Toshiba

Toshiba TS3000 Series Bedienungsanleitung

Toshiba

Toshiba Network Device OIS120 Bedienungsanleitung

Toshiba

Toshiba BMS-IFBN1281U-UL Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba TE2 Series Bedienungsanleitung

Toshiba

Toshiba APOGEE FLN APG001Z Leitfaden

Toshiba

Toshiba Programmable Controller PROSEC T3 Bedienungsanleitung

Toshiba

Toshiba TS2000 Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba VF010H05 Bedienungsanleitung

Toshiba

Toshiba Preliminary TB6560AHQ Bedienungsanleitung

Toshiba

Toshiba Programmable Controller PROSEC T3 Bedienungsanleitung

Toshiba

Toshiba DeviceNet nv Series Bedienungsanleitung

Toshiba

Toshiba RB-RXS34-E Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch