Toshiba 32W1333DB Bedienungsanleitung

SERVICE MANUAL

LCD Color Television

32W1333DB

32W1333DG

32W1333DN

32W1334DG

32W1337DB

32W1337DG

32W1338DG

(System Information)

CONTENTS

1. IMPORTANT NOTICE

2. GREEN PRODUCT PROCUREMENT

3. LEAD-FREE SOLDER

4. SAFETY INSTRUCTION

5. FIRMWARE UPDATING

6. INTERCONNECT

7. EXPLODED VIEW

8. HOTEL MODE / HOTEL CLONE

9. SCHEMATIC DIAGRAM

IMPORTANT NOTICE

WARNING:

You are requested that you shall not modify or alter the information or data provided

herein without prior written consent by Toshiba. Toshiba shall not be liable to

anybody for any damages, losses, expenses or costs, if any, incurred in connection

with or as a result of such modification or alteration.

THE INFORMATION OR DATA HEREIN SHALL BE PROVIDED "AS IS" WITHOUT ANY

WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED WARRANTY OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Toshiba shall not be liable for any damages, losses, expenses or costs, if any,

incurred in connection with or as a result of use of any information or data provided

herein.

GREEN PRODUCT PROCUREMENT

The EC is actively promoting the WEEE & RoHS Directives that define standards for

recycling and reuse of Waste Electrical and Electronic Equipment and for the Restriction of

the use of certain Hazardous Substances. From July 1, 2006, the RoHS Directive will

prohibit any marketing of new products containing the restricted substances.

Increasing attention is given to issues related to the global environmental. Toshiba

Corporation recognizes environmental protection as a key management tasks, and is doing

its utmost to enhance and improve the quality and scope of its environmental activities. In

line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase

and use products, parts and materials that have low environmental impacts.

Green procurement of parts is not only confined to manufacture. The same green parts

used in manufacture must also be used as replacement parts.

LEAD-FREE SOLDER

This product is manufactured using lead-free solder as a part of a movement within the

consumer products industry at large to be environmentally responsible. Lead-free solder

must be used in the servicing and repair of this product.

WARNING: This product is manufactured using lead free solder.

DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT!

The melting temperature of lead-free solder is higher than that of leaded solder by 30ºC to

40ºC (54ºF to 72ºF). Use of a soldering iron designed for lead-based solders to repair

product made with lead-free solder may result in damage to the component and or PCB

being soldered. Great care should be made to ensure high-quality soldering when servicing

this product especially when soldering large components, through-hole pins, and on PCBs

as the level of heat required to melt lead-free solder is high.

(1/ 3)

SAFETY INSTRUCTION

WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT

SAFETY NOTICE" INSTRUCTIONS BELOW.

Safety Precaution

WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE

NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY

PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS.

1. An isolation transformer should be connected in the power line between the receiver

and the AC line before any service is performed on the receiver.

2. Always disconnect the power plug before any disassembling of the product. It may

result in electrical shock.

3. When replacing a chassis in the cabinet, always be certain that all the protective

devices are put back in place, such as nonmetallic control knobs, insulating covers,

shields, isolation resistor-capacitor network, etc.

4. Always keep tools, components of the product, etc away from the children, These

items may cause injury to children.

5. Depending on the model, use an isolation transformer or wear suitable gloves when

servicing with the power on, and disconnect the power plug to avoid electrical shock

when replacing parts. In some cases, alternating current is also impressed in the

chassis, so electrical shock is possible if the chassis is contacted with the power on.

6. Always use the replacement parts specified for the particular model when making

repairs. The parts used in products require special safety characteristics such as

inflammability, voltage resistance, etc. therefore, use only replacement parts that have

these same characteristics. Use only the specified parts when the mark is indicated

in the circuit diagram or parts list.

7. Parts mounting and routing dressing of wirings should be the same as that used

originally. For safety purposes, insulating materials such as isolation tube or tape are

sometimes used and printed circuit boards are sometimes mounted floating. Also

make sure that wirings is routed and clamped to avoid parts that generate heat and

which use high voltage. Always follow the manufactured wiring routes / dressings.

(2/ 3)

8. Always ensure that all internal wirings are in accordance before re-assembling the

external casing after a repairing completed. Do not allow internal wiring to be pinched

by cabinets, panels, etc. Any error in reassembly or wiring can result in electrical

leakage, flame, etc., and may be hazardous.

9. NEVER remodel the product in any way. Remodeling can result in improper operation,

malfunction, or electrical leakage and flame, which may be hazardous.

10. Touch current check. (After completing the work, measure touch current to prevent an

electric shock.)

Plug the AC cord directly into the AC outlet. Do NOT use an isolation transformer for

this check.

Connect a measuring network for touch currents between each exposed metallic part

on the set and a good earth ground such as a water pipe.

Annex D

(normative)

Measuring network for TOUCH CURRENTS

Resistance values in orms (Ω).

V: Voltmeter or oscilloscope

(r.m.s. or peak reading)

Input resistance : 1 MΩ

Input capacitance : 200 pF

Frequency range : 15 Hz to 1 MHz and d.c. respectively

Note: Appropriate measures should be taken to obtain the correct value in case of non

(3/ 3)

sinusoidal waveforms.

The measuring instrument is calibrated by comparing the frequency factor of with

the solid line in figure F.2 of IEC 60990 at various frequencies. A calibration curve is

constructed showing the deviation of from the ideal curve as a function of

frequency.

TOUCH CURRENT = / 500 (peak value).

The potential at any point (TOUCH CURRENT) expressed as voltage and does

not exceed the following value:

The part or contact of a TERMINAL is not HAZARDOUS LIVE if:

a) The open-circuit voltage should not exceed 35 V (peak) a.c. or 60 V d.c. or, if a) is

not met.

b) The measurement of the TOUCH CURRENT shall be carried out in accordance

with IEC 60990, with the measuring network described in Annex D of this standard.

The TOUCH CURRENT expressed as voltages and , does not exceed the

following values:

- for a.c. : = 35 V (peak) and = 0.35 V (peak);

- for d.c. : = 1.0 V

Note: The limit values of = 0.35 V (peak) for a.c. and = 1.0 V for d.c. correspond

to the values 0.7 mA (peak) a.c. and 2.0 mA d.c.

FIRMWARE UPDATING PROCEDURE

Analog - Digital SW update via USB

1. Please copy the files to USB device (root).

 Mb95_en.bin

 mboot.bin

 usb_auto_update_T4.txt

2. Turn power to OFF by mechanical switch or removing AC plug and plug the USB to TV

3. Keep pressing and holding “OK” key from Toshiba remote controller and at the same time turn power to

ON by mechanical SW and hold OK pressed until the standby led blinks very rapidly. Bul led blink time

is longer than MB6X chassis

4. When the blinks of led is stopped, TV opens autamatically.

5. Power OFF / ON TV set, then TV will be ready

When TV is ON

1. Software can be upgraded on Software Upgrade Mode.

2. To access Software Upgrade Mode, you will need to enter “1505 with your remote controller,

3. When main menu is on. On this mode, a simple yes/no screen appears which asks to upgrade the

software.

4. In the USB Mass storage devices, there should be the binary whose name likes ‘upgrade_mb95.bin’.

5. You will see a simple progress menu which shows the status of the upgrade,

6. This will be completed by restarting of the system

Wiring Diagram

1GND

2LED 2

3LED 1

4IR_IN

5 5V_STBY

CN16 CN3 CN100 CN101

1 OP_PIN27 1 24V_VCC_AUO OR GND 124V_VCC_AUO OR GND 1V_Led

2 OP_PIN7 2 GND 2GND 2GND or LED1_S

3 OP_PIN8 3 STBY_ON/OFF 3 STBY_ON/OFF 3 GND or LED2_S

4 OP_PIN9 4 GND 4GND 4NC

5GND , 5 BACKLIGHT_ON/OFF 5BACKLIGHT_ON/OFF 5V_Led

6TX_1_3_P 6GND 6GND 6LED3_S

7TX_1_3_N 7DIMMING 7DIMMING 7LED4_S

8GND 8GND 8GND

9TX_1_CLK_P 9 5V_STBY 9 5V_STBY

10 TX_1_CLK_N 10 12V_STBY 10 12V_STBY

CN27 11 GND 11 5V_VCC 11 5V_VCC

1GND 12 TX_1_2_P 12 5V_VCC 12 5V_VCC

2LED2 13 TX_1_2_N 13 12V_STBY 13 12V_STBY

3LED1 14 GND 14 12V_STBY 14 12V_STBY

4IR_IN 15 TX_1_1_P 15 24V_VCC_AUO 15 24V_VCC_AUO

5 5V_STBY 16 TX_1_1_N 16 3V3_STBY 16 3V3_STBY

17 GND 17 3V3_VCC 17 3V3_VCC

18 TX_1_0_P 18 3V3_VCC 18 3V3_VCC

19 TX_1_0_N 19 GND 19 GND

20 GND 20 GND 20 GND

21 OP_PIN6

22 OP_PIN10

23 OP_PIN5

24 GND

25 GND

26 GND

27 Panel Vcc

28 Panel Vcc CN15

29 Panel Vcc 1R_AUDIO_P

30 Panel Vcc 2R_AUDIO_N

3L_AUDIO_P

4L_AUDIO_N

PANEL

MainBoard MB95S

LED-IR BOARD

Speaker

CN102

1/3

The back cover, the stand, etc. of 32W1334 and 32W1338 are white.

Exploded View

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba LCD-Fernseher Handbücher

Toshiba

Toshiba 19LV61K - 18.5" LCD TV Bedienungsanleitung

Toshiba

Toshiba 52Z3500A Bedienungsanleitung

Toshiba

Toshiba TD-Z552 Bedienungsanleitung

Toshiba

Toshiba Cinema REGZA 46XV648U Bedienungsanleitung

Toshiba

Toshiba REGZA 37HLV66 Bedienungsanleitung

Toshiba

Toshiba RV55* Digital Series Bedienungsanleitung

Toshiba

Toshiba Regza 40XF550U Bedienungsanleitung

Toshiba

Toshiba REGZA 37HL66 Bedienungsanleitung

Toshiba

Toshiba 42SL417U Bedienungsanleitung

Toshiba

Toshiba 40XF355D Bedienungsanleitung

Toshiba

Toshiba 32AV500U - 32" LCD TV Bedienungsanleitung

Toshiba

Toshiba 65U6763DB Bedienungsanleitung

Toshiba

Toshiba 32L154 DG Series Einrichtungshandbuch

Toshiba

Toshiba 32AV563 Bedienungsanleitung

Toshiba

Toshiba M74 Series Bedienungsanleitung

Toshiba

Toshiba 26AV713B Bedienungsanleitung

Toshiba

Toshiba REGZA 52RV535U Bedienungsanleitung

Toshiba

Toshiba WLT68 Bedienungsanleitung

Toshiba

Toshiba 32WL58A Bedienungsanleitung

Toshiba

Toshiba 26AV502R - 26" LCD TV Bedienungsanleitung

Toshiba

Toshiba 26AV502RY Bedienungsanleitung

Toshiba

Toshiba Regza 42LX196 Bedienungsanleitung

Toshiba

Toshiba 37AV50U Bedienungsanleitung

Toshiba

Toshiba 26AV500U - 26" LCD TV Bedienungsanleitung

Beliebte LCD-Fernseher Handbücher anderer Marken

LG 32LC4R* Bedienungsanleitung

ViewSonic

ViewSonic N4200w-1 VS10945-1M Bedienungsanleitung

Salora

Salora 22LED1600 Bedienungsanleitung

Samsung

Samsung LA32E420 Leitfaden

Dell

Dell W1900 19 Gebrauchsanweisung

Samsung

Samsung LN40C670M1F Bedienungsanleitung

Samsung

Samsung Series 4+ Bedienungsanleitung

Samsung

Samsung 5 Series Bedienungsanleitung

Grundig

Grundig 40 VLE 8230 BP Bedienungsanleitung

Philips

Philips 43PFL4901/F7 Bedienungsanleitung

Sony

Sony Bravia XBR-43X830C Bedienungsanleitung

LG 32LS350 Bedienungsanleitung

VIORE

VIORE LED32VF60 Bedienungsanleitung

JVC

JVC LT-32A220 Bedienungsanleitung

Philips

Philips 20TA1000/93 Bedienungsanleitung

Philips

Philips 32PFL3158T/12 Bedienungsanleitung

Sony

Sony Bravia KDL-V32XBR2 Bedienungsanleitung

Vizio

Vizio VP422HDTV10A - 42" Plasma TV Bedienungsanleitung