Toshiba B-415 Bedienungsanleitung

TEC Portable Printer

B-415 SERIES

Owner’s Manual

by TOSHIBA TEC CORPORATION

570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN

by TOSHIBA TEC CORPORATION

570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN

■For AU EMC

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device,

in accordance to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Redirect or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by manufacturer for compliance could void the

user's authority to operate the equipment.

CAUTION

To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.

CAUTION

Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn into

the moving parts, push the switch in the “O” position to stop movement.

CE Compliance (for EU only)

This product complies with the requirements of EMC, Low Voltage and

R&TTE Directives including their amendments.

VORSICHT:

Schallemission: unter 70dB (A) nach DIN 45635 ( oder ISO 7779)

Die für das Gerät Vorgesehene Steckdose muß in der Nähe des Gerätes und leicht zugänglich sein.

“This Class B digital apparatus meets all requirements of the Canadian Interference-Causing

EquipmentRegulations.”

“Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le

matériel brouilleur du Canada.” (for CANADA only)

IrCOMM (9-wire) is a trademark owned by Link Evolution Corporation and is used by TOSHIBA

TEC under license.

The B-415-GH25-QM is equipped with a wireless communication device, TEC-BTM. Please be

sure to read the enclosed Precautions for Handling of Wireless Communication Devices before

using this product.

(i)

Safety Summary ENGLISH VERSION EO1-33014

The B-415-GH25-QM is equipped with a wireless communication device, TEC-BTM. Please be sure to

read the enclosed Precautions for Handling of Wireless Communication Devices before using this product.

Precautions for Handling of Wireless Communication Devices

Bluetooth®Module: TEC-BTM

Trade Mark

Bluetooth is a trademark owned by Bluetooth SIG, Inc. and used by TOSHIBA TEC CORPORATION

under license from Japan Total Design Communication Co., Ltd.

The B-415-GH25-QM is equipped with a certified wireless communication module (TEC-BTM). The

following cautions are applied to the certified wireless module.

Cautions

General

For all countries and areas

This product is a wireless communication device, and the use of this product is restricted to the following

countries or areas. If the product is used in the countries or areas other than the following, you may be

punished according to the laws of those countries or areas.

Japan, USA, Canada, Austria, Belgium, Denmark, Finland, France, Germany, Greece, Italy, Ireland,

Luxembourg, Portugal, Spain, Sweden, The Netherlands, United Kingdom, Australia, New Zealand,

Mexico, Switzerland, Norway, Iceland, Hungary, Liechtenstein

For Europe

Hereby, TOSHIBA TEC CORPORATION, declares that this TEC-BTM is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

This equipment uses a radio frequency band that has not been harmonised throughout all EU and EFTA

countries, and can be used in the following countries.

Austria, Belgium, Denmark, Finland, France, Germany, Greece, Italy, Ireland, Luxembourg, Portugal,

Spain, Sweden, The Netherlands, United Kingdom, Switzerland, Norway, Iceland, Hungary, Liechtenstein

For USA

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

Changes or modification not expressly approved by manufacturer for compliance could void the user’s

authority to operate the equipment.

For Canada

Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including

interference that may cause undesired operation of the device.

(ii)

Safety Summary ENGLISH VERSION EO1-33014

To prevent radio interference to the licensed service, this device is intended to be operated indoors and

away from windows to provide maximum shielding. Equipment that is installed outdoors is subject to

licensing.

For safety

Do not use this product in locations where use may be forbidden, for example, in an aeroplane or a hospital.

If you do not know the forbidden areas, please refer to and follow the airline company or medical institution

guidelines.

Flight instrument or medical equipment may be affected, causing a serious accident.

Since this product uses extremely low power compared with mobile phones, it cannot possibly interfere the

pacemakers and defibrillators. However, if the use

ofthisproductshouldbelikelytohaveaffectedthepacemakerordefibrillator,immediatelystopusingtheproduct

and contact your TOSHIBA TEC sales agent.

Do not disassemble, modify, or repair the product. Doing so may cause injury. Also, modification is against

the Laws and Regulations for Radio Equipment. Please ask your TOSHIBA TEC sales agent for repair.

Precaution in use

This product communicates with other devices by radio. Depending on the installation location, orientation,

environment, etc., its communication performance may deteriorate or devices installed near by may be

affected.

Keep away from a microwave.

Communication performance may deteriorate or a communication error may occur due to the radio emitted

from a microwave.

Keep away from wireless LAN.

The product and wireless LAN may interfere with each other, causing a deterioration of communication

performance or a communication error.

Do not use the product on a metal table or near a metal object.

Communication performance may be deteriorated.

Specification

· Bluetooth class 2

· Built-in protocol stack activated by Bluetooth V1.1 serial port profile

· Operating temperature: -5 to 50°C 25% to 85%RH (No condensation)

· Dimensions: 38.1 mm (W) x 25.4 mm (H) x 7 mm (D)

(iii)

Safety Summary ENGLISH VERSION EO1-33014

Safety Summary

Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions

necessary for safe handling are included in this manual. All warnings and cautions contained in this

manual and written inside or outside of the printer should be read and understood before handling or

maintaining the equipment.

Do not attempt to effect repairs to this equipment. If a fault occurs that cannot be rectified using the proce-

dures described in this manual, turn off the power, then contact your authorised TOSHIBA TEC repre-

sentative for assistance.

Safety Precautions

This Owner's Manual and the products (machines) which you have purchased contain indications which

should be observed in order to use the machines safely and prevent harm to yourself and others and

damage to property. The meanings of these indications and symbols are given below.

Read these indications and become familiar with their contents before reading this Owner's Manual.

WARNING

• If water or any other liquid enters the machine, turn off the power. Continuous use of the machine

under such conditions may cause fire or electric shock.

• If the equipment enclosed is damaged when dropped or subject to shock, turn off the power. Continu-

ous use of the machine under such conditions may cause fire or electric shock.

• Avoid continuous exposure to direct sunlight or high temperature as this may cause fire.

• Do not remove covers or modify the machine by yourself. Doing so may cause fire or electric shock.

• Avoid water, operation with wet hands or cleaning with a moistened cloth. Failure to do this may cause

fire or electric shock.

• Do not wipe the machine with a cloth moistened with thinner or other volatile solvent as this may cause

fire or electric shock.

• Use the specified battery only. Failure to do this may cause fire or electric shock.

• Danger of explosion if the battery is incorrectly replaced. Replace the battery only with 'TOSHIBA TEC

Corporation, Battery Pack Type B-415-BT, 7.2 V 3000 mAh Li-ion'.

Discard used batteries according to the manufacturer's instruction.

• ATTENTION:

II ya denger d'explosion s'il ya remplacement incorrect de la batterrie.

Remplacer uniquement avec une batterie du même type ou d'un type équivalent recommandé par le

constructeur.

Mettre au rebut les batteries usagées conformément aux instructions du fabricant.

• Do not disassemble and modify the battery because it has a protection unit in it. Doing so may break

the protection unit, causing the battery to heat up, burst or burn.

• If the battery gets wet, dry it completely. Using a wet battery may cause fire or electric shock.

• Be aware of the following precautions when using batteries. Otherwise they could heat up, burst or

burn.

■Do not throw the battery into fire or heat it with a microwave or oven, etc.

■Do not load the battery with the electrodes reversed.

■Do not connect the electrodes with metal objects like wire. Do not carry or store the battery along

with metal objects such as necklaces, hairpins, etc.

■Do not stick a needle into, hammer, step on, or drop the battery.

■Do not solder the battery.

■Do not leave the battery where the temperature is more than 60° centigrade, such as inside a car or

in direct sunlight.

This indicates that there is the risk of death or serious injury if the

machines are improperly handled contrary to this indication.

(iv)

Safety Summary ENGLISH VERSION EO1-33014

CAUTION

• Keep away from flame or other sources of heat. Failure to do this may cause fire or machine failure.

• Do not drop or shock the machine as this may cause machine failure.

• During lightening, turn off and keep away from the machine because of danger of electric shock and

machine failure.

• Avoid locations subject to rapid change in temperature as this causes condensation, causing electric

shock or machine failure.

• Do not damage the print head, platen or strip roller with a sharp object. Doing so may cause machine

failure.

• Do not touch or contact the print head element with a metal object. Doing so may cause machine

failure.

• Use the specified media only. Failure to do this may cause machine failure.

• Be sure to turn off the machine before replacing the battery, or machine failure may occur.

• Do not charge the battery near flame or under direct sunlight. High temperature may activate or dam-

age the protection unit of the battery, disabling the electric charge or causing it to overheat, burst, or

burn.

• Unload the battery when the machine will not be used for a long time. Failure to do this may cause

machine failure.

• Keep the battery away from flame, a heat source or other locations subject to high temperature. Failure

to do this may cause it to over heat or burn.

• Use the specified battery charger only. Failure to do this may cause the battery to overheat, burst or

burn.

• Do not force the battery into the machine or battery charger. Doing so may cause the battery to over-

heat, burst or burn. Check for the correct electrode.

• Do not connect the battery to a power outlet or a car cigarette lighter jack as this may cause the battery

to overheat, burst or burn.

• Because the B-415-BT battery is exclusively for the B-415 printer, do not use the battery in other

machines. Doing so may damage the battery or affect the performance and life of the battery.

Precautions

The following precautions will help to ensure that this machine will continue to function correctly.

(1)Try to avoid locations that have the following adverse conditions:

* Temperatures below -5°C and above 50°C

* Direct sunlight

* Excessive vibration

(2)The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild deter-

gent solution. NEVER USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic covers.

(3)USE ONLY TOSHIBA TEC SPECIFIED media.

(4)DO NOT STORE the consumables/media where they might be exposed to direct sunlight, high tempera-

tures, high humidity, dust, or gas.

(5)Any data stored in the memory of the printer could be lost during a printer fault.

(6)DO NOT open the media or battery covers and battery cover during operation. Doing so will stop printer

operation.

(7)DO NOT scratch the surface of printed labels or receipt with a sharp object.

NOTE:

When the printer is not used for a long period of time, please keep it with the media cover open. Failure to do

this may deform the platen by the print head's pressure.

This indicates that there is the risk of personal Injury or damage to

objects if the machines are improperly handled contrary to this indication.

CAUTION:

1. This manual may not be copied in whole or in part without prior written permission of

TOSHIBA TEC.

2. The contents of this manual may be changed without notification.

3. Please refer to your local Authorized Service representative with regard to any queries

you may have in this manual.

ENGLISH VERSION EO1-33014

TABLE OF CONTENTS

Page

1. INTRODUCTION ........................................................................................................E1-1

1.1 Applicable Model ..............................................................................................E1-1

1.2 Accessories ......................................................................................................E1-1

2. SPECIFICATION........................................................................................................E2-1

2.1 Printer...............................................................................................................E2-1

2.2 IrDA Interface ...................................................................................................E2-1

2.3 Serial Interface (RS-232C) (for GH24 and GH34 models)...............................E2-2

2.4 Radio Interface (for GH34 model) ....................................................................E2-2

2.5 Bluetooth Interface (for GH25 model) ..............................................................E2-2

2.6 External DC Input .............................................................................................E2-3

2.7 Battery ..............................................................................................................E2-3

2.8 Option...............................................................................................................E2-3

2.9 Media................................................................................................................E2-4

3. APPEARANCE...........................................................................................................E3-1

3.1 Front/Rear View ...............................................................................................E3-1

3.2 Description of LED Lamp .................................................................................E3-1

3.3 Description of Switch/Button ............................................................................E3-1

4. LOADING AND REMOVING THE BATTERY ........................................................... E4-1

5. ATTACHING THE SHOULDER STRAP....................................................................E5-1

6. SET UP PROCEDURE............................................................................................... E6-1

6.1 Requirements for Operation.............................................................................E6-1

7. LOADING THE LABEL.............................................................................................. E7-1

7.1 How to Load the Liner Backed Label Roll ........................................................E7-1

7.2 How to Load the Linerless Label Roll...............................................................E7-3

8. ISSUING THE MEDIA ................................................................................................E8-1

9. SELF-DIAGNOSTIC TEST PRINT.............................................................................E9-1

10. CARE/HANDLING OF THE MEDIA......................................................................... E10-1

11. GENERAL MAINTENANCE ....................................................................................E11-1

11.1 Cleaning .........................................................................................................E11-1

11.2 Covers and Operation Panel .......................................................................... E11-2

11.3 Removing Jammed Media.............................................................................. E11-2

12. LED DISPLAY AND TROUBLESHOOTING ...........................................................E12-1

13. ERROR PROCESS .................................................................................................. E13-1

E1-1

1. INTRODUCTION ENGLISH VERSION EO1-33014

1. INTRODUCTION

Thank you for purchasing the TEC B-415 series portable printer.

The B-415 printer displays its high performance with extraordinarily high speed printing up to 50.8 mm/

sec. It has a considerably compact and light body of 111 mm in height, 180 mm* in width and 57 mm in

depth, weighing about 800 g. (*The width of the GH25 model is 170 mm.)

There are three models in the B-415 series depending on the wireless communicatio method: IrDA (for

GH24 model), IrDA + Bluetooth (for GH25 model), and IrDA + minute radio (for GH34 model).

Owing to a low power consumption design and use of a chargeable lithium battery as a power source,

this printer can issue 200 pieces of 63.5-mm pitch labels with a fully-charged battery.

Loading a label roll is very simple; just put a label roll into the printer and close the media cover.

This manual contains general set-up and maintenance information and should be read carefully to help

gain maximum performance and life from your printer. For most queries please refer to this manual

and keep it safe for future reference.

1.1 Applicable Model

• B-415 Series

Model name description

B - 4 1 5 - G H 2 4 - Q M

Destination

GB: Great Britain

QP: Europe

QM: Other countries

Interface

24: IrDA + RS-232C

25: IrDA + Bluetooth

34: IrDA + RS-232C + Radio

Issue Type

H: Batch/Strip

S: Batch

Dot density of the print head

G: 8 dots/mm

NOTE: The B-415-GH34-GB model is for exclusive use in Great Britain.

1.2 Accessories

Owner's Manual Print Head Cleaner Lithium ion Battery Pack

(EO1-33014) (24089500013)

1.1 Applicable Model

Linerless Adapter Shoulder Strap

(2 pcs.)

THERMAL HEAD CLEANER

E2-1

2. SPECIFICATIONS ENGLISH VERSION EO1-33014

Item Description

Dimensions GH24/GH34 model: 180 mm (W) x 111 mm (H) x 57 mm (D)

GH25 model: 170 mm (W) x 111 mm (H) x 57 mm (D)

Weight Approximate 800 g (Including a battery)

Operatingtemperature -5°C ~ 50°C

Operatinghumidity 25%~ 85% RH (No condensation)

Issue mode Batch mode/Strip mode

Print head Thermal print head

Print method Thermal direct

Print head dot density 8 dots/mm (203 dpi)

Print speed Max. 50.8 mm/sec.

Effective print width Label: ~ 98.6 mm

Receipt: ~ 101.6 mm

Linerless Label: ~ 91.6 mm

Fonts Standard characters and characters under barcodes (1 size), Bold character

(1 size), Price font (2 sizes), Times Roman medium (6 sizes), Helvetica (6

sizes), Presentation (1 size), Letter Gothic (1 size), Prestige Elite (2 sizes),

Courier (2 sizes), OCR (2 types), Gothic725 Black: 6 point, Writable charac-

ters (2 sizes), TEC font (2 types), Dutch801 bold, Brush738 regular,

Gothic725 black

Bar code types JAN8, JAN13, EAN8, EAN13, UPC-A, UPC-E, CODABAR (NW7), CODE39,

CODE128, EAN128, Interleave 2 of 5, MSI, Data Matrix, PDF417,

Maxi Code, QR Code, Micro PDF417, Customer Barcode,

Prior Customer Barcode

Interface GH24 model: IrDA + RS-232C

GH25 model: IrDA + Bluetooth

GH34 model: IrDA + RS-232C + Radio

Power source Lithium ion battery 7.2V

3000mAh(official)

2.1 Printer

2. SPECIFICATIONS

2.1 Printer

* Data Matrix

is a trademark of International Data Matrix, Inc.

PDF417 is a trademark of Symbol Technologies, Inc.

QR code is a trademark of DENSO CORPORATION.

Maxi code is a trademark of United Parcel Service of America, Inc.

Item Description

Type Physical layer conforming to IrDA-SIR V1.0

Transmission speed 19200 bps

9600 bps (for IrCOMM only)

Communicabledistance 0.3 m max.

Peak wavelength of the infrared ray 850 to 900 nm

Communicableangle ±15° degrees max.

Ambient light immunity 1000 lx max. (under a fluorescent lamp or incandescent lamp)

Intensity of emission Min. 36mW/SR (θh, θv ≤ ±15°)

Receivable infrared ray Min. 7µW/cm2(θh, θv ≤±15°)

Protocol Start-stop synchronization, Half duplex transmission

Start bit = 1 bit, Stop bit = 1 bit, 8 bit data, Non parity

Data code JIS 8 code, Packed BCD code, Shift JIS code

Error detection CRC (16 bits),

Generating polynomical X16+X12+X5+1

Transmission protocol TEC Protocol, IrCOMM (9-WIRE)

2.2 IrDA Interface

E2-2

2. SPECIFICATIONS ENGLISH VERSION EO1-33014

NOTE: This printer requires an exclusive printer cable. When purchasing it, please contact your

authorized TOSHIBA TEC representative.

Item Description

Baud rate 9600 bps

Protocol XON/XOFF, 8 bit data, Even parity, Stop bit = 1 bit

Signals TXD, RXD, RTS, CTS

2.3 Serial Interface (RS-232C) (for GH24 and GH34 models)

Item Description

Type FM superhet UHF radio telemetry receiver (Complies with MPT1340*,

ETS300-220**)

Receiving frequency 418 MHz*, 433 MHz**

Communication method Unidirectional (Receive only)

Transmission speed 4800 bps

Protocol 8 bit data, non parity, stop bit = 1 bit

Communicating distance 3 m

*: GB model

**: QP model

NOTE: The RS-232C interface cable must be disconnected when using the radio communication.

2.5 Bluetooth Interface (for GH25 model)

2.4 Radio Interface (for GH34 model)

The following specification is applicable only to the GB and QP models.

Item Description

Communicationmethod Bluetooth V1.1 (with logo certification)

Supportedprofile Serial port profile

Communication class Class 2

Communication distance 3m/360 degrees

Service name ZV-AT

Device nickname TOSHIBA TEC BT

Flow control Credit based flow control

Operation mode Slave mode

PIN code Not used.

Receive buffer 2 K bytes

Link break time out 20 sec.

Inquiry control No response to any inquiry can be made in 1 minute after the power is

turned ON.

SR mode at page/inquiry scanning R1 scan interval 1.28 sec.

Scan window 22.5 msec.

2.3 Serial Interface (RS-232C) (for GH24 and GH34 models)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Drucker Handbücher

Toshiba

Toshiba TRST-A10 SERIES Bedienungsanleitung

Toshiba

Toshiba B-SX4T Series Bedienungsanleitung

Toshiba

Toshiba B-570 Bedienungsanleitung

Toshiba

Toshiba B-852 Advance Bedienungsanleitung

Toshiba

Toshiba B-EP2DL Series Bedienungsanleitung

Toshiba

Toshiba TEC CB-416-T3-QQ Bedienungsanleitung

Toshiba

Toshiba B-FP2D Series Bedienungsanleitung

Toshiba

Toshiba B-SX600 SERIES Technische Daten

Toshiba

Toshiba B-EP2DL Series Benutzerhandbuch

Toshiba

Toshiba GA-1120 Konfigurationshandbuch

Toshiba

Toshiba TRST-A15 SERIES Bedienungsanleitung

Toshiba

Toshiba MR-2018 Bedienungsanleitung

Toshiba

Toshiba TCx 2tn Bedienungsanleitung

Toshiba

Toshiba E-studio18 Originalbetriebsanleitung

Toshiba

Toshiba SureMark Bedienungs- und Sicherheitshinweise

Toshiba

Toshiba B-SP2D Series Bedienungsanleitung

Toshiba

Toshiba e-STUDIO165 Bedienungsanleitung

Toshiba

Toshiba B-EP4DL-GH20-QM-R Bedienungsanleitung

Toshiba

Toshiba B-880-QQ SERIES Bedienungsanleitung

Toshiba

Toshiba SureMark 4610-SJ6 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO810 GA-1140 Bedienungsanleitung

Toshiba

Toshiba B-EP Series Bedienungsanleitung

Toshiba

Toshiba B-EX4 T1 Series Handbuch

Toshiba

Toshiba B-FP3D-GH52-QM-R Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung