Toshiba B-FP3D SERIES Bedienungsanleitung

PRINTED IN JAPAN

TOSHIBA Potable Printer

B-FP3D SERIES

Document No. EO18-33032C

Original Oct., 2016

(Revised Jul., 2019)

Maintenance Manual

WARNING!

Follow all manual instructions. Failure to do so could create safety hazards such as fire or

electrocution.

NOTE:

Failure to follow manual instructions or any unauthorized modification, substitution or change to

this product will void the limited product warranty.

CAUTION!

1. This manual may not be copied in whole or in part without prior written permission of Toshiba

Tec Corporation.

2. The contents of this manual may be changed without notification.

by Toshiba Tec Corporation

1-11-1, Osaki, Shinagawa-ku, Tokyo 141-8562, JAPAN

TABLE OF CONTENTS

Page

1. UNPACKING .............................................................................................................. 1- 1

1.1 Procedure ........................................................................................................................ 1- 1

1.2 Checks ............................................................................................................................. 1- 1

2. MAJOR UNIT REPLACEMENT .................................................................................. 2- 1

2.1 Replacing the CPU PC Board ......................................................................................... 2- 1

2.2 Replacing the LCD Unit ................................................................................................. 2- 10

2.3 Replacing the Battery Terminal ..................................................................................... 2- 12

2.4 Replacing the Stepping Motor ....................................................................................... 2- 13

2.5 Replacing the Print Head ............................................................................................... 2- 14

2.6 Replacing the PWB Sensor Assembly .......................................................................... 2- 18

2.7 Replacing the Platen Assembly ..................................................................................... 2- 21

2.8 Replacing the Peel-Off Unit ........................................................................................... 2- 23

2.9 Replacing the Peel-off PCB ........................................................................................... 2- 26

2.10 Replacing the Peel-off Roller ......................................................................................... 2- 27

2.11 Replacing the Bluetooth Module .................................................................................... 2- 29

2.12 Replacing the Wi-Fi Module .......................................................................................... 2- 31

2.12.1 Country/Region Code Switching Method for WiFi Module for B-FP3D-GH52 .... 2- 33

2.13 Installation procedure of Rack and Pinion gear (B-FP3D-GH30-FE-R only) ................. 2- 37

2.14 Replacing the Wireless Charger Module (Option-For Future Product) .......................... 2- 38

3. TROUBLESHOOTING ................................................................................................ 3- 1

1. UNPACKING EO18-33032

1.1 PROCEDURE

1-1

1. UNPACKING

1.1 Procedure

1) Open the carton.

2) Unpack the accessories from the carton.

3) Unpack the printer.

NOTE: Keep the carton and pad for future transportation of the printer.

1.2 Checks

1) Check for damage or scratches on the machine.

2) Confirm that none of the accessories are missing.

B-FP3D

2. MAJOR UNIT REPLACEMENT

EO18-33032

2.1 Replacing the CPU PC Board

2-1

2. MAJOR UNIT REPLACEMENT

WARNING!

1. Disconnect the power cord before installing the main parts.

2. Be careful not to injure your fingers when replacing the main parts.

CAUTION!

1. Since a lot of small moulded parts are used in this printer, care must be taken not to damage or lose

them.

2. Be careful not to damage the print head while removing and reassembling.

3. In the United States, used lithium ion batteries should be returned to the store where you bought the

machine. (USA only)

4. LITHIUM ION BATTERY MUST BE DISPOSED OF PROPERLY.

Caution: Do not handle damaged or leaking lithium ion battery.

5. Before handling the main parts, be sure to discharge static electricity in human body through other

metals. Failure to do this may damage the CPU PC board, print head, etc..

NOTES:

1. Before replacing the main parts, print out the maintenance counter values and the parameter values and keep

the printout. (Refer to Section 4.2 Diagnostics Test in the System Mode Manual.)

After replacing, restore the setting according to the printout.

2. Use precision screwdrivers for replacing the precision components which are installed into the printer.

2.1 Replacing the CPU PC Board

1) Turn off the printer.

2) Press down the battery lever to release the battery cover, and then remove Battery Pack from the printer.

3) Remove the four screws from the bottom side of the printer.

Battery Lever

Battery Pack T-3x10 Screw

T-3x40 Screw

2. MAJOR UNIT REPLACEMENT

EO18-33032

2.1 Replacing the CPU PC Board

2-2

4) Push the open button to open the printer.

5) Remove the screws inside the printer.

6) Lift the Function Unit as shown below. The Top cover and the open button can be removed now.

Open Cover

Open Button

Inside screw

Open button

Top Cover

Function Unit

Inside screw

2. MAJOR UNIT REPLACEMENT

EO18-33032

2.1 Replacing the CPU PC Board

2-3

7) Remove the 3 screws and detach the Paper Outlet Guide.

8) Detach the lower sensor to make it easier to handle the function unit.

9) Remove the screw and lift the thermal head cover.

Paper Outlet Guide

Function Unit

Thermal head cover

2. MAJOR UNIT REPLACEMENT

EO18-33032

(Revision Date: Aug., 2017)

2.1 Replacing the CPU PC Board

2-4

10) Push the Lock Lever to Open the Peel Off Unit. (For GH Models only)

11) Push the right side of the Thermal head slightly to dislodge it from the hook.

After it is dislodged, pull it to the right. Be sure to use clean gloves in removing the Thermal head assembly.

For the GH model, remove the adhesive tape from the back of the Thermal head assembly. Be sure to

completely remove the residual glue, too.

Lock Lever

Peel Off Unit

Top View Top View

Note: GH30 and GH50 models have cover

sheets on the PCB components for IP54 rating.

2. MAJOR UNIT REPLACEMENT

EO18-33032

2.1 Replacing the CPU PC Board

2-5

12) Lift the thermal head gently. Carefully detach the Thermal head connector from the PCB.

13) Detach some of the connectors from the Main PCB.

14) Turn the Function Unit upside-down and push the hook in the direction of the arrow and lift the Battery

terminal assembly while carefully removing the different connectors attached to the CPU PC Board.

Battery Terminal Assembly

Hook

Thermal Head Assembly

2. MAJOR UNIT REPLACEMENT

EO18-33032

(Revision date: Aug., 2017)

2.1 Replacing the CPU PC Board

2-6

NOTE:

For this type of connector, you must first push the side locks downward to unlock in order for the flex to be

removed.

15) Remove the screw and detach the connector to take out the CPU PC Board.

For the GH model, remove the IP54 sheet from the Battery frame before removing the CPU PC Board.

Screw

CPU PC Board

Note:

Some connectors can only be detached when the

battery terminal is slightly separated from the

Function Unit.

Connector

Note:

For models with Wi-Fi Module, an additional

ground wire is screwed on the PCB as seen

on the photo. Please remove this.

Andere Handbücher für B-FP3D SERIES

Inhaltsverzeichnis

Andere Toshiba Drucker Handbücher

Toshiba

Toshiba TRST-A10 SERIES Bedienungsanleitung

Toshiba

Toshiba E-studio18 Originalbetriebsanleitung

Toshiba

Toshiba B-SX5T Series Bedienungsanleitung

Toshiba

Toshiba e-STUDIO165 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO400P Konfigurationshandbuch

Toshiba

Toshiba B-EV4 Series Bedienungsanleitung

Toshiba

Toshiba B-FV4D-GS12-QM-R Bedienungsanleitung

Toshiba

Toshiba 4679 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO 305CP Bedienungsanleitung

Toshiba

Toshiba B-EP Series Bedienungsanleitung

Toshiba

Toshiba B-SV4D Series Bedienungsanleitung

Toshiba

Toshiba e-STUDIO382P Bedienungsanleitung

Toshiba

Toshiba e-STUDIO350 Bedienungsanleitung

Toshiba

Toshiba B-415 Bedienungsanleitung

Toshiba

Toshiba 1TN Bedienungsanleitung

Toshiba

Toshiba B-852 Series Bedienungsanleitung

Toshiba

Toshiba B-EX4 SERIES Bedienungsanleitung

Toshiba

Toshiba e-studio 80f Bedienungsanleitung

Toshiba

Toshiba SureMark Bedienungs- und Sicherheitshinweise

Toshiba

Toshiba B-SP2D Series Bedienungsanleitung

Toshiba

Toshiba e-Studio 383P Bedienungsanleitung

Toshiba

Toshiba TEC B-SX4T Series Bedienungsanleitung

Toshiba

Toshiba e-STUDIO GL-1010 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO 20CP Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung