Toshiba B-SA4TP SERIES Bedienungsanleitung

TOSHIBA Thermal Printer

B-SA4TP SERIES

SUPPLY LOADING INSTRUCTIONS

This sheet contains only the media and ribbon loading procedures. Please be sure to read the

Owner’s Manual in the CD-ROM for further information about this printer.

1. LOADING THE MEDIA

CAUTION!

1. Make sure that the Upper Sensor Ass’y is closed when taking out the Media Holder Ass’y. If the Upper

Sensor Ass’y is opened, it may be damaged.

2. Be careful not to touch the Print Head Element when raising the Print Head Block. Failure to do this may

cause missing dots by static electricity or other print quality problems.

ATTENTION !

1. Assurez-vous que le bloc supérieur des cellules de détection est fermé avant de retirer l’ensemble support

média, faute de quoi vous pourriez l’endommager.

2. Faites attention de ne pas toucher la tête d’impression en ouvrant le capot supérieur. De l’électricité statique

pourrait endommager la tête ou entraîner des problèmes de qualité d’impression.

The following procedure shows the steps to properly load the media into the printer so that it feeds straight and

true through the printer. Use the same procedure when replacing the media, also.

The printer prints both labels and tags.

1. Press the Top Cover Release Button and gently open

the Top Cover to its fully open position supporting it

with your hand.

1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc., being drawn into

the moving parts, be sure to load the media once the printer has stopped moving completely.

2. The Print Head becomes hot immediately after printing. Allow it to cool before loading the media.

3. To avoid injury, be careful not to trap your fingers while opening or closing the cover.

AVERTISSEMENT !

1. Ne touchez à aucune pièce en mouvement. Assurezvous d’avoir bien arrêté l’imprimante avant de

charger le média, afin de réduire le risque d’avoir vos doigts, vos bijoux ou vos habits entraînés dans le

mécanisme.

2. La tête chauffe beaucoup en imprimant. Laissez-la refroidir avant de charger le média.

3. Pour éviter les blessures, faites attention de ne pas vous pincer les doigts en ouvrant ou en fermant le

ot.

WARNING!

NOTE:

As the Top Cover is heavy, be sure to support it with your

hand when opening it. Failure to do this may cause the

printer to fall over backward.

Top Cover

Release Button

!00TSCC0188004!

2. Take out the Media Holder Ass’y from the printer.

3. Raise the Release Lever and remove the Media Holder

(Left).

4. Insert the Media Shaft into the core of a media roll.

5. Put the Media Holder (Left) onto the Media Shaft. Push

the Media Holder (Left) and the Media Holder (Right)

against the media until the media is held firmly in place.

This will automatically centre the media.

6. Fold the Release Lever to lock the Media Holder (Left).

NOTE:

When the inner core diameter of the media roll is

40mm, remove the Spacers from the Media Holders.

Media Holder

Ass’y

Upper Sensor

Ass’y

Media Holder (Left)

Release Lever

Media Shaft

Spacer

Media Holder

(Right)

Media Holder

(Left)

Release Lever

Media Holder

(Left)

7. Place the Media Holder Ass’y into the printer.

8. Slightly push the Upper Sensor Lever inside (), and

open the Upper Sensor Ass’y ().

9. Pull the media out of the front of the printer, and

adjust the Media Guides to the media width. This will

automatically centre the media.

10. Lower the Upper Sensor Ass’y until the Upper Sensor

Lever clicks into position.

Media Holder

Ass’y

Upper

Sensor

Ass’y

NOTE:

Be careful of the orientation of the Media Holder Ass’y and

the media.

CAUTION!

Make sure that the Upper Sensor Ass’y is closed when

placing the Media Holder Ass’y into the printer. If the

Upper Sensor Ass’y is opened, it may be damaged.

ATTENTION !

Assurez-vous que le bloc supérieur des cellules de

détection est fermé avant de retirer l’ensemble support

média, faute de quoi vous pourriez l’endommager.

Upper Sensor

Ass’y

Upper Sensor

Lever





Media Guide

Upper

Sensor

Lever

Upper

Sensor

Ass’y

Click

NOTE:

Make sure that the Upper Sensor Ass’y is locked. If it is

unlocked, a paper jam or print failure may occur.

CAUTION!

Be sure to close the Upper Sensor Ass’y before

closing the Top Cover. If the Upper Sensor Ass’y is

opened, it may be damaged.

ATTENTION !

Assurez-vous que le bloc supérieur des cellules de

détection est fermé avant de retirer l’ensemble support

média, faute de quoi vous pourriez l’endommager.

11. After loading the media, it may be necessary to set the

position of the Media Sensor used to detect the print

start position for label or tag printing

Setting the Feed Gap Sensor position

When using a label stock without black marks, the Feed

Gap Sensor is used to detect a print start position.

(1) Push the Upper Sensor Lever inside and open the

Upper Sensor Ass’y.

(2) Slide the Lower Sensor Tab with your finger to move

the Feed Gap Sensor so that the Feed Gap Sensor is

positioned at the centre of the labels. ( indicates the

position of the Feed Gap Sensor).

It may be easier to move the Lower Sensor Tab if you

use a pen inserting its tip into the pinhole of the tab.

(3) Lower the Upper Sensor Ass’y until the Upper Sensor

Lever clicks into position.

(4) Slide the Upper Sensor Tab to move the Feed Gap

Sensor so that it aligns with the lower Feed Gap

Sensor.

Setting the Black Mark Sensor position

When using media with black marks, the Black Mark

Sensor is used to detect a print start position.

(1) Push the Upper Sensor Lever inside and open the

Upper Sensor Ass’y.

(2) Check the reverse side of the media for the black mark

position.

(3) Slide the Lower Sensor Tab to move the Black Mark

Sensor so that it is in line with the centre of the black

mark on the media.

( indicates the position of the Black Mark Sensor).

It may be easier to move the Lower Sensor Tab if you

use a pen inserting its tip into the pinhole of the tab.

Upper

Sensor

Tab

Feed Gap

Sensor

Lower

Sensor

Tab

Black Mark

Sensor

NOTES:

1. Be sure to set the Black Mark Sensor to detect the

centre of the black mark, otherwise a paper jam or no

paper error may occur.

2. After adjusting the Black Mark Sensor position, align

the Upper Feed Gap Sensor with the Lower Feed Gap

Sensor. This is because a paper end is detected by the

Feed Gap Sensor.

NOTE:

Be sure to align the Upper Feed Gap Sensor with the

Lower Feed Gap Sensor. Failure to do this may cause a

paper jam error.

Feed Gap

Sensor Lower

Sensor

Tab

Pinhole

Black

Mark

Media

12. There are three issue modes available on this printer.

How to set the media for each mode is provided

below.

In the batch mode, the media is continuously printed and

fed until the number of labels/tags specified in the issue

command have been printed.

(1) Pull the top edge of the media past the Platen.

(2) Close the Top Cover until it clicks.

When the optional Strip Module is fitted, a label is

automatically removed from the backing paper at the Strip

Plate as each label is printed.

(1) Open the Front Cover holding its right side.

Batch Mode

Strip Mode

(

Option

)

Front Cover Strip Unit

Be careful that your fingers, jewellery, clothing, etc.,

are not draw into the rollers of the Strip Unit.

AVERTISSEMENT !

Prenez garde à ce que vos doigts, un bijou ou une

pièce d’habits ne soit pas entraînés dans les rouages

du mécanisme du

ré décolleur.

WARNING!

(2) Press down the Release Bar to open the Strip Unit.

(3) Remove enough labels from the leading edge of

the media to leave

300mm of backing paper free.

(4) Pass the backing paper through the opening under

the Backing Paper Feed Roller. Then, close the

Strip Unit until it clicks.

(5) Insert the leading edge of the backing paper into the

slot of the Front Cover.

(6) Close the Front Cover and the Top Cover.

When the optional Cutter Module is fitted, the media is automatically cut.

Insert the leading edge of the media into the Media Outlet

of the Cutter Module.

Release Bar

Strip Unit

Backing Paper

Backing Paper Feed Roller

Click

NOTE:

Be sure to close the Strip Unit completely. Failure to

do this may cause a paper jam.

Top Cover

Front Cover

Slot

Cut Mode (Option)

Media

CAUTION!

1. When using a label stock, be sure to cut the gaps.

Cutting labels will cause the glue to stick to the

cutter, which may affect the cutter quality and

shorten the cutter life.

2. Use of tag paper which thickness exceeds specified

value may affect the cutter life.

ATTENTION !

1. Assurez vous de massicoter les étiquettes sur

l’échenillage. Si vous massicotez l’étiquette, de la

colle risque de ’accumuler sur la lame du massicot,

affectant la qualité et la durée de vie de ce dernier.

2. L’utilisation de cartonnette dont l’épaisseur excède

les spécifications peut réduire

The cutter is sharp, so care must be taken not to

injure your fingers when handling the cutter.

AVERTISSEMENT!

Le massicot présente des parties coupantes, prenez

garde à ne pas vous blesser en le manipulant.

WARNING!

13. Change the print head pressure according to the

thickness of the media to be used, by using the Head

Position Lever.

14. If the loaded media is direct thermal media (with a

chemically treated surface), the media loading

procedure is now completed. Close the Top Cover.

If the media is normal media, it is also necessary to

load a ribbon.

2. LOADING THE RIBBON

Head Position Lever







NOTES:

1. Be sure to set both Head Position Levers in the same

direction. Failure to do this may cause blurred

printing.

2. Do not leave the Head Position Levers positioned at the

middle. When closing the Top Cover, they block the

Print Head Positioning Shaft, and the Top Cover cannot

be closed.

Head Position Lever



Head Position Lever

Print Head

Positioning Shaft

Media type or thickness Head Position

Lever



Label or Thin media Move the levers

toward the front

of the printer.

If a clear print cannot be obtained,

change the position to .



Tag paper or Thick paper

Move the levers

toward the back

of the printer

If a clear print cannot be obtained,

change the position to .

CAUTION!

Be careful not touch the Print Head Element when opening the Top Cover. Failure to do this may cause

missing dots by static electricity or other print quality problems.

ATTENTION !

Faites attention de ne pas toucher la tête d’impression en ouvrant le capot supérieur. De l’électricité statique

pourrait endommager la tête ou entraîner des problèmes de qualité d’impression

1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc., being drawn into

the moving parts, be sure to load the ribbon once the printer has stopped moving completely.

2. The print head becomes hot immediately after printing. Allow it to cool before loading the ribbon.

3. To avoid injury, be careful not to trap your fingers while opening or closing the cover.

AVERTISSEMENT!

1. Ne touchez à aucune pièce en mouvement. Assurezvous que l’impression s’est complètement

arrêtée avant de charger le média, afin de réduire le risque d’avoir vos doigts, vos bijoux ou vos

habits entraînés dans le mécanisme.

2. La tête chauffe beaucoup en imprimant. Laissez-la refroidir avant de charger le film.

3. Pour éviter les blessures, faites attention de ne pas vous pincer les doigts en ouvrant ou en

fermant le capot.

WARNING!

NOTE:

When replacing the ribbon, leave the printer power on. Then, press the

[RESTART]

key to restart an operation.

There are two types of media available for printing on: these are thermal transfer media (normal media) and

direct thermal media (with a chemically treated surface). DO NOT LOAD a ribbon when using a direct thermal

media.

1. Press the Top Cover Release Button and gently open

the Top Cover to its fully open position supporting it

with your hand.

2. Fit the core of the ribbon supply roll into the Ribbon

Holders (Supply side), aligning the notch of the ribbon

core with the protrusion of the Ribbon Stopper.

3. Lower the Top Cover to its 45

angle open position.

While pushing the Top Cover Stopper, raise the Top

Cover again. This will fix the Top Cover.

Top Cover

Release Button

Ribbon Holder (Supply side)

Ribbon Supply Roll

Fit the protrusion

into the notch.

Notch

Top Cover

Top Cover Stopper

4. Open the Ribbon Cover.

5. Fit the ribbon take-up core into the Ribbon Holder

(Take-up side), aligning the notch of the ribbon core

with the protrusion of the Ribbon Stopper

6. Turn the ribbon take-up core in the direction indicated

by the arrow to remove any slack.

7. Close the Ribbon Cover until it clicks.

8. Gently close the Top Cover until it clicks.

Ribbon Cover

Ribbon Holder

(Take-up side)

Be sure to close the Ribbon Cover before closing the

Top Cover. It is dangerous to close the Top Cover

with the Ribbon Cover opened, as the Ribbon Cover

slams shut.

AVERTISSEMENT!

Assurez-vous de bien fermer le capot d’accès film

avant de fermer le capot supérieur. Il est dangereux

de fermer le capot supérieur avec le capot film

ouvert,

car celui-ci risque de se refermer en claquant.

WARNING!

Ribbon Cover

Top Cover

NOTES:

1. Be sure to remove any slack in the ribbon when

printing. Printing with a wrinkled ribbon will lower the

print quality.

2. When a ribbon end is detected, “RIBBON ERROR”

message will appear on the display and the ERROR

LED will illuminate.

3. When disposing of the ribbons, please follow the local

rules.

by TOSHIBA TEC CORPORATION

570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN

< For EU Only >

TOSHIBA TEC Europe Retail Information Systems S.A.

Rue de la Célidée 33 BE-1080 Brussels

EO2-33017B

SPTM-0241

Andere Handbücher für B-SA4TP SERIES

Inhaltsverzeichnis

Andere Toshiba Drucker Handbücher

Toshiba

Toshiba TRST-A1 Series Bedienungsanleitung

Toshiba

Toshiba e-STUDIO382P Bedienungsanleitung

Toshiba

Toshiba TRST-A10 SERIES Bedienungsanleitung

Toshiba

Toshiba TRST-A10 SERIES Technische Daten

Toshiba

Toshiba B-SA4TP SERIES Bedienungsanleitung

Toshiba

Toshiba TRST-A15 SERIES Bedienungsanleitung

Toshiba

Toshiba B-670-QQ Bedienungsanleitung

Toshiba

Toshiba TRST-A10 SERIES Bedienungsanleitung

Toshiba

Toshiba B-EP Series Bedienungsanleitung

Toshiba

Toshiba e-studio 162 Bedienungsanleitung

Toshiba

Toshiba SureMark 4610-SJ6 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO 20CP Bedienungsanleitung

Toshiba

Toshiba B-SP2D Series Bedienungsanleitung

Toshiba

Toshiba e-STUDIO 207L Bedienungsanleitung

Toshiba

Toshiba B-EP2DL Series Bedienungsanleitung

Toshiba

Toshiba GA-1120 Konfigurationshandbuch

Toshiba

Toshiba B-SX5T Series Bedienungsanleitung

Toshiba

Toshiba B-852 Advance Bedienungsanleitung

Toshiba

Toshiba TEC B 452 Stücklistenhandbuch

Toshiba

Toshiba B-672-QP Bedienungsanleitung

Toshiba

Toshiba GA-1121 Programmierhandbuch

Toshiba

Toshiba B-FP2D-GH30-QM-S Bedienungsanleitung

Toshiba

Toshiba B-EP2DL Series Benutzerhandbuch

Toshiba

Toshiba B-EP2DL Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung