Toshiba BMS-IFBN1280U-E Bedienungsanleitung

BN interface

Model name:

BMS-IFBN1280U-E

Installation Manual

BN interface

For commercial use

Installation Manual

English

Manuel d’installation

Français

Installationshandbuch

Deutsch

Manuale d’installazione

Italiano

–1–

BN interface Installation Manual

Contents

Precautions for safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Power and signal line connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3-1. Switch setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3-2. LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Factory default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 Test run. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5-1. BACnet communication settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5-2. Setting up equipment data in the indoor unit . . . . . . . . . . . . . . . . . . . . . . . . 12

5-3. Cause of problem occurring during setup . . . . . . . . . . . . . . . . . . . . . . . . . . 12

6 Turning off the BN interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1-EN

–2–

BN interface Installation Manual

Precautions for safety

• Carefully read these "Precautions for Safety" before installation, and perform installation work safely.

• These precautions contain important information regarding safety.

• After installation work, carry out an operation trial to confirm that there are no problems, and explain to the customer how to

operate and maintain the system. Ask the customer to keep this Installation Manual.

Expressions

Graphic symbols

Warning

Text set off in this manner indicates that failure to adhere to the directions in the warning could result

in serious bodily harm (*1) or loss of life if the product is handled improperly.

Caution Text set off in this manner indicates that failure to adhere to the directions in the caution could result

in serious bodily injury (*2) or damage (*3) to property if the product is handled improperly.

*1: Serious bodily harm indicates loss of eyesight, injury, burns, electric shock, bone fracture, poisoning, and other injuries which

leave aftereffect and require hospitalization or long-term treatment as an outpatient.

*2: Bodily injury indicates injury, burns, electric shock, and other injuries which do not require hospitalization or long-term treatment

as an outpatient.

*3: Damage to property indicates damage extending to buildings, household effects, domestic livestock, and pets.

" " indicates prohibited items.

The actual contents of the prohibition are indicated by a picture or text placed inside or next to the

graphic symbol.

" " indicates compulsory (mandatory) items.

The actual contents of the obligation are indicated by a picture or text placed inside or next to the

graphic symbol.

Warning

• Installation and reinstallation should be performed by your dealer or a qualified

electrician

Attempting to carry out installation work on your own, and doing so incorrectly, may result in

electric shock or fire.

• Electrical work must be performed by a qualified electrician in accordance with

this Installation Manual. The work must satisfy all local, national and international

regulations

Inappropriate work may result in electric shock or fire.

• Be sure to turn off the power before starting work

Failure to do so may result in electric shock.

• Use only the power adapter supplied with this unit

A power adapter other than that supplied with this unit may provide a different voltage and have

different polarity (+) (−), which could lead to fire, explosion or generation of heat.

• Do not modify the unit

Doing so may result in excessive heat or fire.

Warning

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may

be required to take adequate measures.

The following instructions

must be observed.

Prohibited

Compulsory

2-EN

–3–

BN interface Installation Manual

Introduction

Overview

The BN interface refers to equipment used for controlling Building Management Systems (Procured locally) and air conditioners

“TU2C-LINK Uh Line (hereinafter, referred to as Uh Line) compatible models” through communications via a network to enable

central control.

Included Items

Specifications

External View (BN interface equipment)

Component Q'ty Remarks

BN interface equipment 1

Power adapter 1BN interface power supply (model name: UI318-0526) (not include Power Cable)

Pin terminal 2Uh Line caulked connectors

Mounting bracket (DIN rail) 1Use screws to secure the unit in locations without DIN rails (walls, etc.)

Screws (M4 x 12) 2For securing the DIN rails

Rubber feet 4For levelling the unit

Screws (M3 x 8) 4For securing the rubber feet to the unit

Installation Manual 1This manual

License Agreement 1

License Information 1

Tie-wrap 1

Power supply Rated voltage 220-240 VAC 50/60 Hz

Power consumption 3 W

Operating temperature range 0°C to 40°C, 10% to 80% RH (no condensation)

Storage temperature range −10°C to +60°C, 10% to 90% RH (no condensation)

Dimensions Width 140 mm x Height 90 mm x Depth 45 mm

Mass BN interface 260 g

Power adapter 140 g







䣒䣑䣙䣇䣔䣎䣋䣐䣍䢪䣗䣪䢫䣅䣒䣗

(5525

About 12~13

3-EN

–4–

BN interface Installation Manual

(Power adapter)

REQUIREMENT

Power cable is not supplied for the BN Interface. Insert a two core power cord applicable to the standard of the country you use.

Component Names

Name Function

5V DCIN Connect the power adapter

USB (For service)

Ethernet (LAN) Connect to the Building Management System

Shutdown button Shutdown or switch to air-conditioning search mode

L1 BACnet communication status indicator

L2 BACnet communication status indicator, setting error indicator

722/,1*1268%

s

s

s

s











䣒䣑䣙䣇䣔䣎䣋䣐䣍䢪䣗䣪䢫䣅䣒䣗

(5525

86%

/

/

9'&,1

(WKHUQHW/$1

6KXWGRZQEXWWRQ

4-EN

–5–

BN interface Installation Manual

1Installation

REQUIREMENT

Do not install the unit in any of the following places.

• Humid or wet place

• Dusty place

• Place exposed to direct sunlight

• Place where there is a TV set or radio within one meter

• Place exposed to rain (outdoors, under eaves, etc.)

BN Interface Installation and Orientation

Install and orient the interface using the DIN rail to mount the unit or wall mount or surface mount it as shown below.

Use the supplied mounting bracket to wall mount or surface mount the interface.

(3) Surface mount

Use screws to secure the supplied rubber legs to the interface before surface mounting it.

(1) DIN rail mount

Install the interface on DIN rails mounted on a switchboard or elsewhere.

Front view Back view

(2) Wall mount

Use screws to attach the supplied

DIN rails to a wall and install the

interface on the DIN rail.

Wall mount A Wall mount B Wall mount C

Supplied DIN rail

Supplied rubber leg

mounting screw

5-EN

–6–

BN interface Installation Manual

Installation Space and Maintenance Space

A side space for connecting through cable inlets and an upper space for maintenance must be reserved before installation.

The other sides can be adjacent to surrounding objects.

PP

6-EN

–7–

BN interface Installation Manual

2Power and signal line connections

Cables

Use the following cable for signal line connections. (Procured locally)

Ethernet®is a registered trademark of Xerox Co., Ltd.

Cable Connections

Connect the cables to the specified connectors.

Length of stripped Uh Line communication cable

CAUTION

The Uh Line communication cable have no polarity.

* Secure the Uh Line communication cable and power cable to the switchboard etc. using the supplied cable tie to ensure

that no excess load is placed on the power cable connection and Uh Line communication cable connection.

No. Line Description

1For Uh Line

Type 2-core shielded wires

Wire size 1.25 mm2, 1000 m max. total length

including air conditioner wiring length

Length 2.00 mm2, 2000 m max.

2For Ethernet®Type

LAN cable (higher than Category 5, UTP)

The appropriate use of straight cable/cross cable should be done depending on your

system used

Length 100 m max.

50 10

Connect the supplied pin terminal to the Uh Line

communication cable as necessary.

8K/LQH 9'&,1 (WKHUQHW/$1

Connection of Uh Line

communication

cables

Connect the

supplied power

adapter

Connect the LAN

cable

The Uh Line communication cable must be

earthed on the air conditioner.

Do not connect the shield wire to the

connector. It should be open and

insulated.

Air conditioner

7-EN

–8–

BN interface Installation Manual

Example of System Wiring Connections

8K/LQH 9'&,1 (WKHUQHW/$1

䣒䣑䣙䣇䣔䣎䣋䣐䣍䢪䣗䣪䢫䣅䣒䣗

(5525

+8%

8 8

8

8

8 8

8 8

88

8 8

BN interface

Building Management System

Power adapter Power Supply

Uh Line main bus

Outdoor unit

Indoor unit Indoor unitRemote

controller

Remote

controller

8-EN

–9–

BN interface Installation Manual

3Settings

3-1. Switch setting

SW300 Not used

SW301 Test switch

Set all bits to "OFF".

SW302 Test button

Not used during normal operation.

SW100 Uh Line terminator resistor setting switch

Set the Uh Line terminator resistor on the air conditioner side. Set SW100 to "OFF".

SW700 Shutdown function / air-conditioning search mode function button

Use this button to stop BACnet process and network process of the BN interface or to start up in the air-conditioning

search mode. Note that button operation changes depending on how long it is depressed.

Time duration button is depressed Operation

Less than 4 seconds Stop BACnet process and network process of the BN interface.

4 seconds or more Starts air-conditioning in the air-conditioning search mode.

Use the air-conditioning search mode to set up equipment data in the indoor

unit.

6: 6: 6: 6:

6:

9-EN

Andere Handbücher für BMS-IFBN1280U-E

Inhaltsverzeichnis

Sprachen:

Andere Toshiba Aufnahmegeräte Handbücher

Toshiba

Toshiba APOGEE FLN APG001Z Stücklistenhandbuch

Toshiba

Toshiba RBM-Y1123FE Bedienungsanleitung

Toshiba

Toshiba BMS-IFBN1280U-E Bedienungsanleitung

Toshiba

Toshiba TCB-IFGSM1E Bedienungsanleitung

Toshiba

Toshiba TCB-IFTH1GUL Bedienungsanleitung

Toshiba

Toshiba TCB-IFGSM1E Bedienungsanleitung

Toshiba

Toshiba W602C Bedienungsanleitung

Toshiba

Toshiba ESTiA Bedienungsanleitung

Toshiba

Toshiba LonWorks TCB-IFLN642TLUL Bedienungsanleitung

Toshiba

Toshiba BMS-IFMB1280U-E Bedienungsanleitung

Toshiba

Toshiba Stratagy 24SBC Service-Handbuch

Toshiba

Toshiba BMS-IFWH4E2 Bedienungsanleitung

Toshiba

Toshiba RAV-DXC010 Bedienungsanleitung

Toshiba

Toshiba Carrier RBM-Y0611F4PUL Bedienungsanleitung

Toshiba

Toshiba NV Series Bedienungsanleitung

Toshiba

Toshiba G1IF1 Bedienungsanleitung

Toshiba

Toshiba Strata DK Backup Bedienungsanleitung

Toshiba

Toshiba W-705 Bedienungsanleitung

Toshiba

Toshiba TCS-NET Gebrauchsanweisung

Toshiba

Toshiba BMS-IFDD02E2 Bedienungsanleitung

Toshiba

Toshiba HWS-IFAIP01U-E 0-10V Bedienungsanleitung

Toshiba

Toshiba BMS-IFMB1280U-E Bedienungsanleitung

Toshiba

Toshiba TCS-NET Bedienungsanleitung

Toshiba

Toshiba G1IF4 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch