Toshiba TCS-NET Gebrauchsanweisung

TCS-NET GENERAL PURPOSE INTERFACE

Setting Tool Manual

For advanced conjunction function

Model name:

TCS-NET General Purpose Interface

TCB-IFCG1TLE

(TCB-IFCG2TLE)

Contents

1. Introduction ............................................................................................................................... 2

2. Overview of the System............................................................................................................ 2

3. Necessary equipment and software ......................................................................................... 2

4. Operating Environment and Installation.................................................................................... 3

5. Serial Port Setup File Format ................................................................................................... 4

6. How to Use the GP Setting Tool............................................................................................... 5

7. Errors ...................................................................................................................................... 12

Toshiba

+00DE89308701_01EN_General_Setting_Tool_M.book Page 1 Thursday, November 27, 2008 1:17 PM

TCS-NET General Purpose Interface Setting Tool Manual

Toshiba

1. Introduction

This manual describes how to use the setting tool software for the advanced conjunction function for the general

purpose interface. The setting tool allows writing, reading, and erasing air conditioning control data to respond to

input port changes for the general purpose I/F board (TCB-IFCG1TLE, referred to as GP hereinafter).

2. Overview of the System

This manual is intended for the setting tool for operations in conjunction with the GP.

Set the switches on the GP to SW5-5: OFF and SW5-6: ON, connect the connector CN5 on the GP to the RS232C

connector on the PC with the DYNA KIT cable, connect the power line of the GP, and then press the RESET button

(SW7) on the GP.

3. Necessary equipment and software

Product Product name Obtain from

DYNA KIT cable Adapter CNV2-3.3V Carrier sales company

.NET Framework Microsoft .NET Framework 2.0 or later Download from Microsoft web site.

Writing tool software Setting tool software for advanced conjunction

function for the General Purpose Interface

Carrier sales company

PC Windows XP or 2000 with RS232C port —

General Purpose I/F board (GP)

RS232C

+00DE89308701_01EN_General_Setting_Tool_M.book Page 2 Thursday, November 27, 2008 1:17 PM

TCS-NET General Purpose Interface Setting Tool Manual

Toshiba

4. Operating Environment and Installation

4-1. Operating Environment

Supported OS: Windows XP / 2000

Microsoft .NET Framework 2.0 or higher and a serial port are necessary to operate this system.

4-2. Required Files and Installation

• Microsoft .NET Framework 2.0 or higher can be downloaded from the Microsoft website.

• Copy the following files to an appropriate directory.

- serialPort.txt

- GPSettingTool.pdb

- GPSettingTool.exe

4-3. Serial Port Setting

Set the serial port as follows:

• Baud Rate = 38400 bps

• Data bit = 8

• Parity check = no parity

• Stop bit = 1

• No flow control

• COM port = COM1 (default)

• Timeout = 2 seconds (default)

Fixed

+00DE89308701_01EN_General_Setting_Tool_M.book Page 3 Thursday, November 27, 2008 1:17 PM

TCS-NET General Purpose Interface Setting Tool Manual

Toshiba

5. Serial Port Setup File Format

The COM port and timeout period settings can be changed with the setup file “serialPort.txt”. However, even if the

settings are changed after startup, the setting change is not reflected because these settings are made during

system startup. If there is an error in the setup file, an error message appears and the GP setting tool is not

activated. The COM port and timeout period cannot be changed independently. Therefore, when changing either

COM port or timeout period, both COM port or timeout period must be set together. If the setup file does not exist

in the same directory, the default settings of the COM port and timeout period are used.

• Type a COM port name using capital alphabets on the first line.

If small letters (e.g. com) are entered, an error occurs.

• Type a timeout value in second on the second line.

A value from 1 to 300 (seconds) can be set. If a value outside this range (e.g. –1, 0, or 400) or a fractional value

(e.g. 1.5) is entered, an error occurs.

If these settings are entered on other lines or space or other characters are used before or after the port name and

timeout value, an error occurs.

Ex. COM port COM 5

Timeout : 10 sec.

+00DE89308701_01EN_General_Setting_Tool_M.book Page 4 Thursday, November 27, 2008 1:17 PM

TCS-NET General Purpose Interface Setting Tool Manual

Toshiba

6. How to Use the GP Setting Tool

6-1. Startup

Start the GPSettingTool.exe.

+00DE89308701_01EN_General_Setting_Tool_M.book Page 5 Thursday, November 27, 2008 1:17 PM

TCS-NET General Purpose Interface Setting Tool Manual

Toshiba

6-2. Write Operation

The set data of the selected patterns can be written to the GP.

The set data of other patterns in the GP remains unchanged when the set data of the selected patterns is written.

When the set data of the selected patterns already exists, it is overwritten to the new data by the write operation.

The write operation takes time in some cases.

6-2-1. Selecting Patterns

Click the checkboxes of patterns you want to select.

Two or more patterns are selectable.

Click the Toggle All button to select all patterns or cancel selection of all patterns.

If no pattern is selected, an error occurs.

+00DE89308701_01EN_General_Setting_Tool_M.book Page 6 Thursday, November 27, 2008 1:17 PM

TCS-NET General Purpose Interface Setting Tool Manual

Toshiba

6-2-2. Setting Trigger Port and Condition

Select the tab of the selected pattern to set Trigger Port and Condition.

If no Trigger Port is selected, an error occurs.

When selecting values for Condition, if the same value is selected for before and after (e.g. before = H, after = H),

an error occurs.

When digital input (DI1 to DI6) is selected for Trigger Port, if values except for the combinations shown below are

selected, an error occurs. “H” corresponds to the state where input current does not flow to the relevant DI port,

and “L” corresponds to the state where the input current flows to the relevant DI port.

Before After

+00DE89308701_01EN_General_Setting_Tool_M.book Page 7 Thursday, November 27, 2008 1:17 PM

TCS-NET General Purpose Interface Setting Tool Manual

Toshiba

6-2-3. Setting Relay CH and Air Conditioning Control Data

The following items can be set for air conditioning control data.

• On/OFF

• Operating mode

• Set temperature

• Fan speed

• Disabling of remote control (ON/OFF only)

Each central control address (1 to 64) can be set individually, and all addresses (1 to 64) can also be set collectively

with the All button. However, the All button cannot be used for setting set temperature and fan speed. While setting

of an item (e.g. operating mode HEAT) is made for all addresses, if the setting of the same item is made for an

address (e.g. address 10), an error occurs.

If no data is set for both Relay CH and air conditioning control data, an error occurs.

Up to 30 settings can be made for air conditioning control data. If excess settings are made, an error occurs.

For each central control address, set temperature and fan speed are treated as one air conditioning control data.

Example) In the case of the following window, there are six settings as is one air conditioning control data.

+00DE89308701_01EN_General_Setting_Tool_M.book Page 8 Thursday, November 27, 2008 1:17 PM

TCS-NET General Purpose Interface Setting Tool Manual

Toshiba

6-2-4. Writing Set Data

After all data have been set, click the Write button.

A confirmation message appears. Confirm the message and click the OK button to send the set data.

To cancel the write operation, click the Cancel button.

After the writing is completed, a completion message appears.

+00DE89308701_01EN_General_Setting_Tool_M.book Page 9 Thursday, November 27, 2008 1:17 PM

TCS-NET General Purpose Interface Setting Tool Manual

Toshiba

6-3. Read Operation

When the set data of the selected pattern is stored in the GP, the data can be read and displayed on the window.

During this read operation, only the data of the selected pattern is displayed and the display contents of other

patterns on the window are completely cleared.

The read operation takes time in some cases.

6-3-1. Selecting Patterns

Click the checkboxes of patterns you want to select.

Two or more patterns are selectable.

Click the Toggle All button to select all patterns or cancel selection of all patterns.

If no pattern is selected, an error occurs.

6-3-2. Reading Set Data

Click the Read button after patterns are selected.

A confirmation message appears. Confirm the message and click the OK button to read the set data.

To cancel the read operation, click the Cancel button.

After the reading is completed, a completion message appears and the read data is displayed on the window of

the selected pattern.

If there is no set data, a confirmation message appears indicating “no data.”

+00DE89308701_01EN_General_Setting_Tool_M.book Page 10 Thursday, November 27, 2008 1:17 PM

Andere Handbücher für TCS-NET

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Aufnahmegeräte Handbücher

Toshiba

Toshiba TCS-NET Bedienungsanleitung

Toshiba

Toshiba OIS PLUS Series Bedienungsanleitung

Toshiba

Toshiba BMS-IFMB1280U-E Bedienungsanleitung

Toshiba

Toshiba W602C Bedienungsanleitung

Toshiba

Toshiba BMS-IFWH4E2 Bedienungsanleitung

Toshiba

Toshiba Stratagy 24SBC Service-Handbuch

Toshiba

Toshiba TCB-IFDMX01UP-E Bedienungsanleitung

Toshiba

Toshiba BMS-IFDD02E2 Bedienungsanleitung

Toshiba

Toshiba Black Pear Bedienungsanleitung

Toshiba

Toshiba BMS-IFKX0AWR-E Bedienungsanleitung

Toshiba

Toshiba BMS-IFBN1280U-E Bedienungsanleitung

Toshiba

Toshiba TCB-IFGSM1E Bedienungsanleitung

Toshiba

Toshiba Carrier RBM-Y0611F4PUL Bedienungsanleitung

Toshiba

Toshiba W-705 Bedienungsanleitung

Toshiba

Toshiba BMS-IWF0320E Bedienungsanleitung

Toshiba

Toshiba RBM-Y1123FE Bedienungsanleitung

Toshiba

Toshiba G1IF4 Bedienungsanleitung

Toshiba

Toshiba NV Series Bedienungsanleitung

Toshiba

Toshiba RBM-Y0384FUL Bedienungsanleitung

Toshiba

Toshiba BMS-IFMB1280U-E Bedienungsanleitung

Toshiba

Toshiba TCB-IFGSM1E Bedienungsanleitung

Toshiba

Toshiba LonWorks TCB-IFLN642TLUL Bedienungsanleitung

Toshiba

Toshiba Surveillix EAV Series Bedienungsanleitung

Toshiba

Toshiba Strata DK Backup Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch