Toshiba MK6034GAX Series Kurzanleitung

2.5” Hard Disk Drive Installation Notes - MK1234GAX/MK6034GAX Series P/N 480071-A0 P/N 480071-A0 2.5” Hard Disk Drive Installation Notes - MK1234GAX/MK6034GAX Series

12/05 12/05

TOSHIBA STORAGE DEVICE DIVISION

2.5" HDD INSTALLATION NOTES

MK1234GAX and MK6034GAX Series

Contents subject to change without prior notice.

GENERAL DESCRIPTION

Toshiba’s 9.5mm series of 2.5" Hard Disk Drives is comprised of fast, high-capacity

drives which comply with ATA-6 standards. Toshiba recommends that these drives be

installed by a qualified technician. Additional installation hardware may be required

depending on how and or where the drive is being installed.

Specifications MK1234GAX MK6034GAX

HDD2D16 HDD2D17

Formatted Capacity 120.034GB 60.012GB

Height 9.5mm 9.5mm

# of Disks (platters) 2 1

# of Data Heads 4 2

FUNCTIONAL SPECIFICATION

Logical Drive MK1234GAX MK6034GAX

Parameters HDD2D16 HDD2D17

# of Cylinders (user) 79,056 79,056

Bytes per Sector 512 512

LBA Sectors 234,441,648 117,210,240

Buffer Size (KBYTES) 8,192 8,192

Rotation Speed (±.1%) 5400 5400

Transfer Rate Internal 243.7 – 468.9 243.7 – 468.9

(MBITS/sec.)

# of Cylinders (logical) 16,383 16,383

# of Heads 16 16

# of sec./Track 63 63

PIO/Ultra DMA (MBITS/sec.) 16.6/100 16.6/100

Seek Time (MSEC.)

Average 12 12

Track-to-track 2 2

Maximum 22 22

CABLING INFORMATION

DRIVE INTERFACE SIGNALS

PIN SIGNAL PIN SIGNAL

1 -RESET 2 GROUND

3 DD 7 4 DD 8

5 DD 6 6 DD 9

7 DD 5 8 DD 10

9 DD 4 10 DD 11

11 DD 3 12 DD 12

13 DD 2 14 DD 13

15 DD 1 16 DD 14

17 DD 0 18 DD 15

19 GROUND 20 KEY

21 DMARQ 22 GROUND

23 -DIOW 24 GROUND

STOP

25 -DIOR 26 GROUND

-DMARDY

HSTROBE

27 IORDY 28 CSEL

-DMARDY

-DSTROBE

29 -DMACK 30 GROUND

31 INTRQ 32 - IOCS16

33 DA1 34 - PDIAG

35 DA0 36 DA 2

37 - CS0 38 - CS1

39 - DASP 40 GROUND

41 +5V (LOGIC) 42 +5V (MOTOR)

43 GROUND 44 RESERVED

Note: Symbol (–) in front of signal indicates negative logic.

TECHNICAL SUPPORT

Should you require technical support, contact your computer distributor. If your distributor

is unable to answer your questions, have them call Toshiba Storage Device Division Techni-

cal Support, on your behalf.

TOSHIBA - STORAGE DEVICE DIVISON TECHNICAL SUPPORT

PHONE: 510/651-6798 FAX: 510/623-9893

EMAIL: [email protected]

You can also visit Toshiba’s web site at: http://www.sdd.toshiba.com

2.5” Hard Disk Drive Installation Notes - MK1234GAX/MK6034GAX Series P/N 480071-A0 P/N 480071-A0 2.5” Hard Disk Drive Installation Notes - MK1234GAX/MK6034GAX Series

12/05 12/05

UNPACKING PROCEDURE

Visually inspect the shipping container prior to unpacking for any signs of damage to

the container or its contents (the carrier is responsible for any damage incurred during

shipment). The drive is a precision device and even a small drop onto any surface can

cause damage. Prior to opening the anti-static bag, it is recommended that the user

ground themself with a ground strap or by touching the PC chassis or other metal object.

Remove the drive from the anti-static bag and check it for damage. Place the drive on the

anti-static bag while configuring jumpers to avoid any electrostatic discharge. Save the

shipping container and packing material for possible use later.

DRIVE CONFIGURATION

Toshiba’s 2.5" hard disk drives can be configured as either master or slave units. Master

configuration is used for all single drive applications, and master or slave configuration

(only one of each per port) is used for two drive applications. Use the information in the

following table before setting M/S drive.

Master configuration is obtained by setting jumpers B, C & D open (no jumper). Slave

configuration is obtained by setting jumpers C-D. When B-D jumper is installed, the

drive is configured as cable select. If pin 28 = Low, the drive is master. If pin 28 = High,

the drive is slave.

FIGURE 1 – 2.5" HDD JUMPER LOCATIONS

JUMPER P28 DRIVE

No Jumper - Master Drive

C-D Jumper - Slave Drive

B-D Jumper LOW Master Drive

B-D Jumper HIGH Slave Drive

A-B Jumper - Slave Drive/

A-C Jumper - Prohibit

FIGURE 2 – MOUNTING HOLE LOCATIONS

INSTALLATION INSTRUCTIONS

Note: Toshiba’s 2.5” HDDs are primarily used in notebook devices. Installation into a

notebook varies depending on the system manufacturer. Toshiba’s 2.5” drives that

are installed into a desktop PC require a 3.5” installation kit.

1. Determine mounting configuration (can be mounted in either a horizontal or verti-

cal orientation).

2. Configure drive for system application.

3. Install the I/F cable to the system’s 44 pin connector port or adapter board (if

required). Ensure Pin 1 is oriented correctly. (Pin 1 on the cable is usually identi-

fied by a red or blue stripe.)

4. Refer to applicable manuals for software installation instructions.

KEY

PIN 20

1CA

JUMPERS

INTERFACE

CONNECTOR

MOUNTINGHOLES