Toshiba MK8009GAH Kurzanleitung

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH

Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes

TOSHIBA STORAGE DEVICE DIVISION

MK4009GAL & MK8009GAH

HDD INSTALLATION NOTES

Contents subject to change without prior notice.

GENERAL DESCRIPTION

Toshiba’s MK4009GAL (HDD1622) and MK8009GAH (HDD1584) hard disk drives

are a series of ultra-slim fast light weight 1.8 inch Winchester disk drive. The drives are

ATA-6 compliant.

SPECIFICATIONS MK4009GAL MK8009GAH

HDD1622 HDD1584

FORMATTED CAPACITY 40.0GB 80.0GB

HEIGHT 5mm 8mm

WEIGHT 1.69oz (48g) 2.08oz (59g)

NO. OF DISKS (PLATTERS) 1 2

NO. OF DATA HEADS 2 4

FUNCTIONAL SPECIFICATION

LOGICAL DRIVE MK4009GAL MK8009GAH

PARAMETERS HDD1622 HDD1584

NO. OF CYLINDERS (user) 62,640 62,640

BYTES PER SECTOR 512 512

BUFFER SIZE 8MB 2/8MB

ROTATION SPEED (±0.1%) 4,200rpm

TRANSFER RATE INTERNAL 165.0 - 356.8 Mbits/sec.

NO. OF CYLINDERS (logical) 16,383

NO. OF HEADS (logical) 1 6

NO. OF SECTORS/TRACK 6 3

HOST TRANSFER RATE

PIO/ULTRA DMA (ATA mode) 16.6/100MB/s

SEEK TIME

AVERAGE 15ms

TRACK-TO-TRACK 3ms

MAXIMUM 26ms

TEMPERATURE

OPERATING 41°F - 140°F (5°C - 60°C)

NON-OPERATING -4°F - 149°F (-20°C - 65°C)

HUMIDITY

OPERATING/NON-OPERATING 8 - 90% R.H. (No condensation)

SHIPPING 5 - 90% R.H. (No condensation)

WET BULB 29°C(operating)/40°C(non-operating)

CONNECTOR CABLING INFORMATION

The following table describes all of the pins on the Task File Interface:

PIN SIGNALS PIN SIGNALS

1 RESERVED 2 RESERVED

3 - RESET 4 GROUND

5 DD7 6 DD8

7 DD6 8 DD9

9 DD5 10 DD10

11 DD4 12 DD11

13 DD3 14 DD12

15 DD2 16 DD13

17 DD1 18 DD14

19 DD0 20 DD15

21 GROUND 22 DMARQ

23 GROUND 24 - DI0W

STOP

25 -DIOR 26 GROUND

-HDMARDY

HSTROBE

27 IORDY 28 GROUND

-DMARDY

DSTROBE

29 DMACK 30 INTRQ

31 DA1 32 - PDIAG/-CBLID

33 DA0 34 DA2

35 -CS0 36 -CS1

3 7 - DASP 3 8 +3.3V

39 +3.3V 40 RESERVED

Note: “-“ in front of signal name indicates negative logic.

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH

Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes

UNPACKING PROCEDURE

Visually inspect the shipping container prior to unpacking for any signs of damage to

the container or its contents (the carrier is responsible for any damage incurred during

shipment). Prior to opening the anti-static bag, it is recommended that the user ground

himself with a ground strap or by touching the PC chassis or other metal object. Re-

move the drive from the anti-static bag and check it for damage. Save the shipping

container and packing material for possible use later.

HANDLING AND MOUNTING CONSIDERATIONS

•Installation and mounting of these drives is specific to the application environment.

•Handle drive only by the edges. When handling or mounting, take care not to apply

any pressure to the top cover.

•Avoid subjecting the drive to excessive shock. Do not drop the drive, even a

small distance onto a tabletop or other hard surface can damage drive. When

mounting the drive, do so in such a fashion that the drive will be isolated from

excessive shock.

•Do not mount in an environment where the temperature of the drive’s top cover will

exceed 65°C. (During operation, the temperature of the top cover can rise 15°C

above ambient).

•Do not disassemble, modify or repair drive.

•A rattle heard when the drive is moved is normal and not a sign of failure.

INTERFACE CONNECTOR

Drive Side Connector DDK Ltd, FF19A-40B-R11b

Recommended host side FPC 1. Width: 20.50 ±0.07mm

2. Thickness: 0.20 ±0.03mm

3. Length: 90mm (max)

4. Impedance: Typical 50ohm

5. Plating: Gold over Nickel plating (note 1)

6. Adhesive: Heat-hardened adhesive

Connector Durability (note 2) 20 times

FPC Holding fource (note 3) Typ: 17[N] Min: 5[N]

* Do not pull out FPC with the connector locked.

* Do not lock without FPC

Notes:

1. To avoid Sn whisker

2. In horizontal direction with FPC of 0.20mm in thickness and with the same

connector and FPC

3. In horizontal direction with FPC of 0.20mm in thickness and with the same

connector and FPC after pulling out repeatedly

FIGURE 1 – INTERFACE CONNECTOR

DEVELOPER SUPPORT

Toshiba Storage Device Division (SDD) the industry pioneer in small form factor

storage supports developers who are looking for small form factor HDD’s that deliver

the unbeatable combination of high-performance and high-capacity storage. Toshiba

HDD’s can be found “under the hood” of some of today’s hottest portable products. If

you are interested in discussing your product application with us please contact us.

E-mail: [email protected]

Phone: (949) 462-7502

Fax: (949) 588-7845

Web: http://developer.toshiba.com

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH

Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes

UNPACKING PROCEDURE

Visually inspect the shipping container prior to unpacking for any signs of damage to

the container or its contents (the carrier is responsible for any damage incurred during

shipment). Prior to opening the anti-static bag, it is recommended that the user ground

himself with a ground strap or by touching the PC chassis or other metal object. Re-

move the drive from the anti-static bag and check it for damage. Save the shipping

container and packing material for possible use later.

HANDLING AND MOUNTING CONSIDERATIONS

•Installation and mounting of these drives is specific to the application environment.

•Handle drive only by the edges. When handling or mounting, take care not to apply

any pressure to the top cover.

•Avoid subjecting the drive to excessive shock. Do not drop the drive, even a

small distance onto a tabletop or other hard surface can damage drive. When

mounting the drive, do so in such a fashion that the drive will be isolated from

excessive shock.

•Do not mount in an environment where the temperature of the drive’s top cover will

exceed 65°C. (During operation, the temperature of the top cover can rise 15°C

above ambient).

•Do not disassemble, modify or repair drive.

•A rattle heard when the drive is moved is normal and not a sign of failure.

INTERFACE CONNECTOR

Drive Side Connector DDK Ltd, FF19A-40B-R11b

Recommended host side FPC 1. Width: 20.50 ±0.07mm

2. Thickness: 0.20 ±0.03mm

3. Length: 90mm (max)

4. Impedance: Typical 50ohm

5. Plating: Gold over Nickel plating (note 1)

6. Adhesive: Heat-hardened adhesive

Connector Durability (note 2) 20 times

FPC Holding fource (note 3) Typ: 17[N] Min: 5[N]

* Do not pull out FPC with the connector locked.

* Do not lock without FPC

Notes:

1. To avoid Sn whisker

2. In horizontal direction with FPC of 0.20mm in thickness and with the same

connector and FPC

3. In horizontal direction with FPC of 0.20mm in thickness and with the same

connector and FPC after pulling out repeatedly

FIGURE 1 – INTERFACE CONNECTOR

DEVELOPER SUPPORT

Toshiba Storage Device Division (SDD) the industry pioneer in small form factor

storage supports developers who are looking for small form factor HDD’s that deliver

the unbeatable combination of high-performance and high-capacity storage. Toshiba

HDD’s can be found “under the hood” of some of today’s hottest portable products. If

you are interested in discussing your product application with us please contact us.

E-mail: [email protected]

Phone: (949) 462-7502

Fax: (949) 588-7845

Web: http://developer.toshiba.com

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH

Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes

TOSHIBA STORAGE DEVICE DIVISION

MK4009GAL & MK8009GAH

HDD INSTALLATION NOTES

Contents subject to change without prior notice.

GENERAL DESCRIPTION

Toshiba’s MK4009GAL (HDD1622) and MK8009GAH (HDD1584) hard disk drives

are a series of ultra-slim fast light weight 1.8 inch Winchester disk drive. The drives are

ATA-6 compliant.

SPECIFICATIONS MK4009GAL MK8009GAH

HDD1622 HDD1584

FORMATTED CAPACITY 40.0GB 80.0GB

HEIGHT 5mm 8mm

WEIGHT 1.69oz (48g) 2.08oz (59g)

NO. OF DISKS (PLATTERS) 1 2

NO. OF DATA HEADS 2 4

FUNCTIONAL SPECIFICATION

LOGICAL DRIVE MK4009GAL MK8009GAH

PARAMETERS HDD1622 HDD1584

NO. OF CYLINDERS (user) 62,640 62,640

BYTES PER SECTOR 512 512

BUFFER SIZE 8MB 2/8MB

ROTATION SPEED (±0.1%) 4,200rpm

TRANSFER RATE INTERNAL 165.0 - 356.8 Mbits/sec.

NO. OF CYLINDERS (logical) 16,383

NO. OF HEADS (logical) 1 6

NO. OF SECTORS/TRACK 6 3

HOST TRANSFER RATE

PIO/ULTRA DMA (ATA mode) 16.6/100MB/s

SEEK TIME

AVERAGE 15ms

TRACK-TO-TRACK 3ms

MAXIMUM 26ms

TEMPERATURE

OPERATING 41°F - 140°F (5°C - 60°C)

NON-OPERATING -4°F - 149°F (-20°C - 65°C)

HUMIDITY

OPERATING/NON-OPERATING 8 - 90% R.H. (No condensation)

SHIPPING 5 - 90% R.H. (No condensation)

WET BULB 29°C(operating)/40°C(non-operating)

CONNECTOR CABLING INFORMATION

The following table describes all of the pins on the Task File Interface:

PIN SIGNALS PIN SIGNALS

1 RESERVED 2 RESERVED

3 - RESET 4 GROUND

5 DD7 6 DD8

7 DD6 8 DD9

9 DD5 10 DD10

11 DD4 12 DD11

13 DD3 14 DD12

15 DD2 16 DD13

17 DD1 18 DD14

19 DD0 20 DD15

21 GROUND 22 DMARQ

23 GROUND 24 - DI0W

STOP

25 -DIOR 26 GROUND

-HDMARDY

HSTROBE

27 IORDY 28 GROUND

-DMARDY

DSTROBE

29 DMACK 30 INTRQ

31 DA1 32 - PDIAG/-CBLID

33 DA0 34 DA2

35 -CS0 36 -CS1

3 7 - DASP 3 8 +3.3V

39 +3.3V 40 RESERVED

Note: “-“ in front of signal name indicates negative logic.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Lagerung Handbücher

Toshiba

Toshiba STOR.E CANVIO Bedienungsanleitung

Toshiba

Toshiba MK1676GSX Bedienungsanleitung

Toshiba

Toshiba MK5002MPL Bedienungsanleitung

Toshiba

Toshiba PX02SM series Bedienungsanleitung

Toshiba

Toshiba MK2556GSY Bedienungsanleitung

Toshiba

Toshiba HDTC910EK3AA Bedienungsanleitung

Toshiba

Toshiba MK1060GSC Bedienungsanleitung

Toshiba

Toshiba MK3021GAS Bedienungsanleitung

Toshiba

Toshiba MK3006GAL Bedienungsanleitung

Toshiba

Toshiba Canvio AeroCast Bedienungsanleitung

Toshiba

Toshiba MK2565GSX Konfigurationshandbuch

Toshiba

Toshiba XM-7002B Bedienungsanleitung

Toshiba

Toshiba MK6025GAS Bedienungsanleitung

Toshiba

Toshiba STOR.E ALU 2 Bedienungsanleitung

Toshiba

Toshiba MK1255GSX Konfigurationshandbuch

Toshiba

Toshiba MK2008GAL Bedienungsanleitung

Toshiba

Toshiba CanvioDTQ112 Bedienungsanleitung

Toshiba

Toshiba Canvio Slim Bedienungsanleitung

Toshiba

Toshiba MK3252GSX Konfigurationshandbuch

Toshiba

Toshiba microSDHC Bedienungsanleitung

Toshiba

Toshiba MG03ACA400 Bedienungsanleitung

Toshiba

Toshiba TransMemory Bedienungsanleitung

Toshiba

Toshiba MK6014MAP Bedienungsanleitung

Toshiba

Toshiba STOR.E ALU 2S Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

HP P9000 Bedienungsanleitung