Toto EcoPower TEL3GSC Bedienungsanleitung

0GU3007E 2006.3

1~2

Important Safeguards .............

Precautions ..............................

Model Number and

Components ..............

NOTE TO INSTALLER : PLEASE GIVE THIS MANUAL TO THE

CUSTOMER AFTER INSTALLATION.

Before Use ...............................

How to Use ...............................

How to Adjust ..........................

6~7

7~8

Maintenance .............................

Periodical Checking ................

9~10

Troubleshooting ....................

Specications ..........................

WARRANTY

AUTOMATIC FAUCET

DISCONTINUED

below

local code

Controller

After you read this Instruction Manual, keep it where it can be easily referred to again.

Symbols are shown for safe and proper use of your Automatic Faucet and in order to alert you possible

personal injury and damage to your property. The symbols and their meanings are as follows.

The items of observation are classied and described.

Some models may have dierent component as illustrated below.

Do not install the product in high

humidity area such as shower

room or sauna.

Absolutely "Do not".

Do not disassemble.

Do not

touch the area specied.

This means mandatory.

Do not

Do not use in

humid areas

Do not

disassemble

Never splash water on the controller.

The Automatic Faucet is an electrical appliance, this may cause product

malfunction.

Do not strike or kick to the Automatic Faucet.

This may cause product malfunction or water leakage.

Do not place an item with this symbol displayed in a room

with high humidity such as shower room or sauna.

This may cause product malfunction.

Do not use the

Automatic Faucet at temperatures exceeding

what local codes allow.

It may cause product malfunction.

Never attempt to disassemble, reassemble, repair or modify

the

Automatic Faucet, unless you are an electrician

This may cause product malfunction and electric shock.

Warning

Read these Important Safeguards thoroughly before using your Automatic Faucet, and

follow the precautions carefully.

Warning Ignoring these symbols may cause personal injury or

property damage.

Important Safeguards

(For your safety, please follow the instructions below.)

Getting Started

DISCONTINUED

How to Use

Getting Started

Disconnect

Controller

Ouch!

leakage!

Brrrr

Don't touch

Mandatory

Do not touch the stop valve of the controller, the surface

may be very hot.

This may cause personal injury.

For EcoPowermodel, disconnect the

back-up battery

connector, when the Automatic

Faucet is not in use for a

long period of time.

Always close the stop valve(s) before cleaning the strainer

(Refer to P.8)

Hot or cold water may ow out and cause personal injury or property damage.

Periodically check the piping

for leakage.

Ignoring this may cause property damage.

When the room temperature falls under freezing condition,

give proper care to the piping to prevent product malfunction.

If the piping is frozen, the components may suer damage and leakage.

Wrap the piping with heat insulation.

Warning

●Make sure the power cord does not come in contact with the hot-water supply pipe.

　(In case of thermostatically controlled mixing valve.)

High temperature may damage the product.

●Avoid placing any objects within the detection range of the infrared sensor.

May result in faulty operation .

●Occasionally turn the temperature control handle of the thermostatically controlled mixing

valve to prevent buildup or sticking.

Debris may form inside of the valve, resulting in impaired performance. Routine maintenance must be performed.

Precautions

(Observe the following precautions.)

DISCONTINUED

Getting Started

How to Use Troubleshooting

How to Use

Getting Started

Maintenance Troubleshooting

< Model Number >

Standard

Gooseneck

Single Supply Faucet Thermal Mixing Valve Faucet

Battery type Battery type

TEL3GSC

TEL3GGC

TEL -10

TEL -60

TEL5GSC

TEL5GGC

TEL5DSC

TEL5DGC

TEL3DSC

TEL3DGC

Duration of water discharge : 10 seconds

Duration of water discharge : 60 seconds

Spout

Standard

Battery

Controller

Single Supply Faucet

Thermal Mixing Valve Faucet

P.5

spout connecting

hose with exible tube

controller

cover

temperature

control handle

water inlet bracket

with strainer

sensor cord

P.5

sensor cord

spout connecting

hose with exible tube

controller

cover

water inlet bracket with strainer

spout connecting

hose with exible tube

P.7

batteries

controller

cover

sensor cord

water inlet bracket

with strainer

P.5

temperature control handle

water inlet bracket

with strainer

spout connecting

hose with exible tube

sensor

cord

controller

cover

P.7

batteries

spout

P.4・6

sensor part

sensor

cord

spout connecting hose

spout outlet

hexagonal nut

spout connecting hose

hexagonal nut

sensor

cord

spout outlet

EcoPower®type EcoPower®type

EcoPower®

EcoPower

Gooseneck

P.4・6

sensor part

sensor

EcoPower®

Model Number and Components

DISCONTINUED

How to Use

Troubleshooting

Make sure all connections are made.

Conrmation of connectors

Cover

Pull

Screw

Battery type

Cover

Screws

Sensor connector

(green)

Battery connector

(for battery type : white)

Sensor connector (green)

Screw

Cover

Battery connector

(for battery type : white)

For Single supply faucet For Thermal mixing valve faucet

1. Place your hands under the faucet.

The sensor will automatically turn on the water.

2. Remove your hands.

The sensor will automatically turn o the water.

Normal operation

Sensor connector (green)

Back-up battery connector (for EcoPowertype : white)

Battery connector (for battery type : white)

Back-up battery connector

(for EcoPowertype : white)

Back-up battery connector

(for EcoPowertype : white)

EcoPowertype

Before Use

How to Use

DISCONTINUED

How to Use Maintenance Troubleshooting

Mechanism for Hydropowered generator

The ow of water causes the turbine in the power generator to rotate, which generates electric power, and enables the

Automatic Faucet to operate.

Spout Power generator

1A turbine rotates to

generate power.

2Electric power

is stored.

The Automatic Faucet

is using the charged

power.

Water supply

Controller

Controller unit

Solenoid valve

Cover

Coil

Turbine

Using the faucet 11 times a day for 5 seconds or more will fully recharge the faucet.

Turn the temperature control handle.

The water temperature has been factory set to 100°F (38°C).

Depending on the conditions of both the cold and hot water

supply, adjust the temperature by turning the temperature control

handle as necessary.

How to adjust the temperature

Adjustment of the ow rate

※Thermostatically controlled mixing valve

Temperature control handle

Hot

Cold

Open

Stop valve

Bits of Knowledge About EcoPowerModel

With the built-in regulator valve - 1.06gpm (4L/min.), there is no need to adjust the ow rate.

Use the Automatic Faucet with the stop valve fully opened.

If you need to regulate the ow rate, adjust it by turning the stop valve.

However, the EcoPowermodel must be used with the stop valve fully opened.

If you need to regulate the ow rate, make sure the ow rate is more than

0.8gpm (3L/min.).

How to Adjust

DISCONTINUED

How to Use

Maintenance

Follow these instructions for daily maintenance.

For general cleaning

For cleaning dirt

Avoid using anything that may scratch the spout surface.

Do not scratch the sensor when cleaning.

Never use polishing powder, detergent that includes coarse particles,

thinner, benzine, acid or alkaline detergent, or a nylon scrub brush.

They will damage the surface of the spout.

Caution

Use a damp, soft cloth to clean the spout and the sensor.

Use a soft cloth with diluted dish washing detergent.

Wipe the area using a wet cloth and dry using a soft cloth.

Sensor part

Outlet

Low Battery Indicator (Battery operated models)

If continued to use after

1ST indication

2ND Indication1ST Indication

Flow time reduced to 2

seconds. (Normally 10

or 60 seconds)

Water ow will stop and

sensor light will blink every

4 seconds.

Sensor light

Sensor

Use only AA alkaline batteries (2pcs) .

2 years battery life expectancy ,

based on 4,000 cycles per month.

Replace batteries every 2 years as

preventative maintenance.

Battery Specications

Use soft cloth for maintenance

Maintenance

DISCONTINUED

How to Use Maintenance

leakage!

1. Remove the controller cover. (See page 4)

2. Detach the battery connector (white).

3. Remove the rubber cover from the battery

case and replace the AA alkaline batteries.

4. Reassemble.

Replace only with 2 AA alkaline batteries.

Follow the "battery warning note" on the

batteries.

Please remove batteries from the faucet

when not in use for a long period of time.

Caution

battery case

controller

battery case

controller

For Thermal mixing valve faucet

For Single supply faucet

Battery Replacement Procedure (Battery operated models)

battery connector

(white)

Disconnect white

connector by hand

battery connector (white)

batteries

rubber cover

battery case

Please check your Automatic Faucet at least once a month according to the following instructions.

Check the piping

to see whether there is any leakage.

Ignoring this may cause property damage.

Leakage

For thermostatically controlled mix valve, turn the

temperature control handle four or ve times.

Build up may form inside, resulting in impaired performance

if maintenance is not performed.

Water temperature

Temperature

control handle

Controller

Periodical Checking

DISCONTINUED

Maintenance

Check if the spout is loose.

If the spout is loose, tighten the hexagonal nut underneath the spout.

Loose spout

1. Close the stop valve.

2. Remove the strainer cover with the open-close

tool.

3. Pull out the strainer and clean it with a brush.

4. Put the strainer back in its place.

5. Reopen the stop valve fully.

Cleaning the strainer

1. Remove the spout nozzle with the supplied

open-close tool.

2. Clean the spout nozzle with a brush to

remove dirt from the screen.

3. Set the spout nozzle back in place.

Cleaning of the spout nozzle

Flow rate

Stop valve

Open

Open-close tool

Strainer

Strainer cover

Open

Brush

Strainer

Open-close tool

Open

Brush

Spout nozzle

When the strainer or spout nozzle is clogged, the ow rate

will decrease.

Make sure to clean the strainer and the spout nozzle.

Pay special attention to the Eco power model, since low ow

rate may result in low power generation. (see page 5)

DISCONTINUED

Troubleshooting

Before contacting a repairman, check the following common problems and solutions. If the problem persists contact your dealer.

Problem Cause Solution Ref. page

Water doesn't run.

Water doesn't stop.

The surface of the sensor is dirty. Clean the surface of the sensor. P.6

P.2

P.5

P.4

P.8

P.7

P.6

P.2

The surface of the sensor is dirty. Clean the surface of the sensor.

There is an obstruction in front of the sensor. Remove the obstruction.

The stop valve is turned o. Turn on the valve.

Connect the backup battery connector.

The power generator and sensor connection

are not attached. Securely attach the connector(s).

Water supply is suspended. Wait until water supply is restored.

The strainer or the spout nozzle is clogged. Clean the strainer and the spout nozzle.

The batteries are dead. Replace the batteries.

Battery-operated model: No batteries

installed. Install batteries in the controller.

If water continues to run after attempting above, turn o the stop valve.

Low ow rate. Stop valve is not fully opened. Open the stop valve fully.

The strainer or the spout nozzle is clogged. Clean the strainer and the spout nozzle.

Water temperature

is too high.

Water temperature

is too low.

The temperature control handle is set at "H". Set the temperature control handle to

the middle point.

The stop valve connected to the cold-water

supply is not fully opened. Open the cold-water stop valve fully.

The temperature control handle is set at "C".

Set the temperature control handle

the middle point.

The stop valve connected to the hot- water

supply is not fully opened. Open the hot-water stop valve fully.

The hot-water supply temperature is lower

than 120°F (49°C).

Set the hot-water supply temperature

to 120°F (49°C).

The strainer or the spout nozzle is clogged.

The batteries are dead.

Water temperature

is not controlled

properly.

Water ow from the

faucet stops about 2

seconds later.

Clean the strainer and the spout nozzle.

Replace the batteries.

One side of the stop valve is not fully opened. Open the stop valve fully. P.5

P.8

P.7

The self-adjusting sensor may not work

properly

when stained or blocked by water

droplets.

Short detection range.

Clean the sensor surface. P.6

EcoPowermodel: Backup battery connector

is disconnected.

Troubleshooting

DISCONTINUED

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toto Küchen- und Badezimmerausstattung Handbücher

Toto

Toto Keane TS211EV Montageanleitung

Toto

Toto Keane TL211SDR Montageanleitung

Toto

Toto TEN40AW V105 Bedienungsanleitung

Toto

Toto Keane TS211T Montageanleitung

Toto

Toto PJS01W Technisches Handbuch

Toto

Toto Connelly TL221DD Montageanleitung

Toto

Toto EcoPower TEL3LSC Bedienungsanleitung

Toto

Toto Keane TL211SD Montageanleitung

Toto

Toto YH406R Bedienungsanleitung

Toto

Toto Keane TL211DDR Montageanleitung

Toto

Toto Silas TB210DD Montageanleitung

Toto

Toto Connelly TB221S Montageanleitung

Toto

Toto WH099 Series Bedienungsanleitung

Toto

Toto ZA TLP03301U Montageanleitung

Toto

Toto Mercer TS756A Montageanleitung

Toto

Toto EcoPower Automatic Faucets Montageanleitung

Toto

Toto TB100SF Montageanleitung

Toto

Toto Connelly TS221EV Montageanleitung

Toto

Toto TB100SFBN Montageanleitung

Toto

Toto Wyeth TB230S Montageanleitung

Toto

Toto Keane TL211DD Montageanleitung

Toto

Toto STD TELS10 Series Montageanleitung

Toto

Toto Vivian Alta TL220DDH Montageanleitung

Toto

Toto Vivian TB220S Montageanleitung

Beliebte Küchen- und Badezimmerausstattung Handbücher anderer Marken

Grohe

Grohe BRIDGEFORD 33 870 Bedienungsanleitung

Hans Grohe

Hans Grohe Zenio Metro 31811000 Bedienungsanleitung

Gröne

Gröne Zedra 32 555 Bedienungsanleitung

Transform

Transform QL045 Bedienungsanleitung

Sanela

Sanela SLU 09PTB Bedienungsanleitung

Glacier bay

Glacier bay FP4A0052BNV Montageanleitung

Lefroy Brooks

Lefroy Brooks C1-1400 Montageanleitung

Grohe

Grohe Rapido E Bedienungsanleitung

Danze

Danze D302455 Bedienungsanleitung

Waterworks

Waterworks CEKM30 Merkblatt

Helvex

Helvex Omega TV-298 Bedienungsanleitung

Tribata.

Tribata. GEORGIAN G5393 Bedienungsanleitung

Alpha Bidet

Alpha Bidet Alpha One Bedienungsanleitung

InSinkErator

InSinkErator H/HC3300 Installationshandbuch

Clou

Clou Xo type 1 Bedienungsanleitung

Kohler

Kohler Contra 26448T-4 Bedienungsanleitung

Grohe

Grohe Bridgeford 20 158 Bedienungsanleitung

Hans Grohe

Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Bedienungsanleitung