Town & Country Fireplaces TC42.NG04D Bedienungsanleitung

Visit www. townandcountryﬁreplaces.net for the most recent version of this manual

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

These instructions are supplementary to the Installation and

Operating Instructions supplied with the replace and should be

kept together. Refer to the Installation and Operating Instructions for

proper gas supply, safety requirements and operating instructions

TC42

TRANQUILITY

BURNER KIT

INSTALLATION

INSTRUCTIONS

PART# TC42.

NG04D

For TC42 Series D

Fireplaces

090117-16 TC42_NG04D 5056.426D4

Figure 1: Tranquility burner kit package contents.

Figure 2: Pre-existing gas ex lines. Figure 3: Left side cover. Figure 4: Right side cover.

5056.426D4 2TC42_NG04D_090117-16

If converting to propane see conversion instructions on page 10 before proceeding.

NOTE: Plug the 4 vacant holes in the bottom of the ﬁrebox with 1/2” screws, as they are not required to

attach this style of burner.

1 Burner assembly

1 Panel, base

1 Pebble assembly

1 Cover, right side

1 Cover, left side

3.4 lbs sand

1 Bag tapered plugs

Tranquility Burner Installation

Contents of Package

1. Reshape the pre-existing gas ex lines into the approximate shape needed to t the new burner (Figure 2).

2. Place left and right covers under the burner tray (Figure 2 and Figure 3).

NOTE: Shutter must be fully closed for Natural gas, fully open for Propane.

Figure 6: Panel clips.

5056.426D4

TC42_NG04D_090117-16

Figure 5: Lower rear panel.

3. Position lower rear porcelain panel centered at the rear of the rebox. Place burner assembly into the

rebox against the rear panel (Figure 5).

4. Place panel clips under both rear corners of the base plate as shown in Figure 6 (approx. 3” from rear

panel).

5056.426D4 4TC42_NG04D_090117-16

5. Attach the manifold supply tube and the pilot supply tube to the bulk head ttings and tighten (Figure 7).

Ensure that there are no leaks.

Figure 7: Gas and pilot supply tubes.

Bulkhead plate

Ignition and sensor wires

Figure 8: Ignition and sensor wires routing.

6. Secure the electrical bulkhead plate and gasket to the rebox with 2 screws (Figure 8).

5056.426D4

TC42_NG04D_090117-16

Ignition wire (red)

Flame sensor

wire (white)

Interface module

Figure 9: Interface module.

7. Attach the ignition and sensor wires to the module (Figure 9).

8. Remove panel retainer from upper heat shield. Install right porcelain panel tilting in from front corner

(Figure 10).

Figure 10: Right side panel installation.

Figure 12: Upper rear panel installation.

5056.426D4 6TC42_NG04D_090117-16

Figure 11: Inserting side panel into panel clip.

9. Slip the side panels into the panel clip as shown in Figure 11.

10. Position upper rear panel on the top of the lower rear panel and behind the right panel. While supporting

the upper rear panel install and secure left porcelain panel in the same manner as the right panel (Figure 12)

Secure with the previously removed panel retainer.

Figure 13: Securing sliding cover.

Figure 14: Inserting tapered plugs.

5056.426D4

TC42_NG04D_090117-16

11. Slide covers out and attach to base with one screw each (Figure 13).

12. Insert tapered plugs into raised burner ports to prevent sand from entering ports (Figure 14).

Figure 15: Adding sand to tray.

Figure 16: Positioning pebble assembly.

5056.426D4 8TC42_NG04D_090117-16

13. Place sand in tray. Brush sand smooth and level to just below top of raised burner ports (Figure 15).

14. Gently blow excess sand from around ports.

15. Remove tapered plugs from ports.

Figure 17: Trim rocks added to pebble assembly.

5056.426D4

TC42_NG04D_090117-16

NOTE:

Lift pebble assembly from bottom. Do not lift by top rocks. Hollowed out rock must cover the pilot.

NOTE:

Do not place trim rocks on top of the pebble assembly. Sooting will occur.

16. Remove pebble assembly from packaging by placing hand on top and tipping upside down. Gently place

pebble assembly onto sand base using pins to locate position (Figure 16).

17. Place trim rocks at desired locations in the sand around the pebble assembly. Install glass door. Unit is

ready for lighting.

Figure 18: Removing burner tray screws. Figure 19: Replacing orice.

Conversion procedure

5056.426D4 10 TC42_NG04D_090117-16

The burner assembly must be removed from the unit if previously installed.

1. Remove the 2 front screws holding the burner tray in place (Figure 18).

2. Gently lift up the burner tray while sliding it to the left to disengage the burner tube from the orice. Then

tip back to expose the orice.

3. Using a 1/2” wrench, undo the natural gas burner orice (Figure 19). Apply a small amount of pipe joint

compound to the threads of the propane burner orice to ensure a good seal, before screwing it into the

tting.

Propane Conversion

If the unit is to be used with propane gas, convert the ﬁreplace from natural gas as follows

using the components supplied with this burner kit. For complete valve installation instruc-

tions , refer to the instruction book included in the SIT conversion kit.

Note: Factory supplied components must be used to ensure correct input. After conversion conrm proper

manifold pressure.

WARNING

This conversion kit shall be installed by a qualiﬁed service agency in accordance with the manufac-

turer's instructions and all applicable codes and requirements of the authority having jurisdiction.

If the information in these instructions is not followed exactly, a ﬁre, explosion or production of car-

bon monoxide may result causing property damage, personal injury or loss of life.

The qualiﬁed service agency is responsible for the proper installation of this kit.

The installation is not proper and complete until the operation of the converted appliance is checked

as speciﬁed in the manufacturer's instructions supplied with the kit.

CAUTION

The gas supply and electrical power must be shut off before proceeding with the conversion.

Andere Handbücher für TC42.NG04D

Inhaltsverzeichnis

Andere Town & Country Fireplaces Brenner Handbücher

Town & Country Fireplaces

Town & Country Fireplaces TC36.NG03C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.NG01 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42.NG04D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42.NG06C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42.NG03C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Series Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42.NG02DN Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces D Series Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42.NG06D2 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.NG06C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.NG04D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30.NG02DN Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54.NG04C2 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.NG04C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30.NG04C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.NG06.D2 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.38CE2 Gebrauchsanweisung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.NGST03C Bedienungsanleitung

Beliebte Brenner Handbücher anderer Marken

Riello

Riello RS 28/M Kurzanleitung

True Induction

True Induction TI4B Bedienungsanleitung

Weishaupt

Weishaupt WG20 Series Bedienungsanleitung

Carolina Cooker

Carolina Cooker M116672 Bedienungsanleitung

Riello

Riello RX 500 S/PV Bedienungsanleitung

Unigas

Unigas HTP2000 Bedienungsanleitung

baltur

baltur BT 250 DSG 4T Bedienungsanleitung

muenkel design

muenkel design round burner Bedienungsanleitung

baltur

baltur BT 14 DSGW Bedienungsanleitung

artisan

artisan Art-SB1 Leitfaden

AESYS

AESYS TurboFire II Bedienungsanleitung

Riello

Riello RG1RKD Kurzanleitung

IKEA

IKEA GRILLSKÄR Bedienungsanleitung

RUSTA

RUSTA SAREK Bedienungsanleitung

PROPOINT

PROPOINT 8933657 Bedienungsanleitung

baltur

baltur TBL 1000 ME Referenzhandbuch

Riello Burners

Riello Burners P 200 P/G Kurzanleitung

WLD-TEC

WLD-TEC powerjet Bedienungsanleitung