Toyota TVIP V4 Bedienungsanleitung
Rev. B 01/18/06
REMOTE ENGINE STARTER
TROUBLESHOOTING GUIDE
2009- RAV4 w/Smart TVIP V4 REMOTE ENGINE STARTER (RES)
TROUBLESHOOTING GUIDE
Remote Engine Starter Troubleshooting Guide Page 2
TABLE OF CONTENTS
DESCRIPTION PAGE
PRE-CHECK 3
RES ECU PIN LAYOUT AND TERMINALS 4-5
ACCESSORY GATEWAY ECU PIN LAYOUT
AND TERMINALS 6
HOW TO PROCEED WITH TROUBLESHOOTING 7
CUSTOMER PROBLEM ANALYSIS CHECK 8
PROBLEM SYMPTOMS TABLE 9
DIAGNOSTIC OPERATION 10-11
Diagnosis Mode Reset Conditions 12
DIAGNOSTIC CODE BY SCAN TOOL 12
INSPECTIONS
Engine Does Not Start by Remote 13-15
Engine Does Not Stop by Remote 16-17
Engine Stops Unexpectedly 18-19
Failed Registration of Immobilizer ID Code 20-21
Remote Engine Starter Troubleshooting Guide Page 3
PRE-CHECK
REMOTE ENGINE STARTER CHARACTERISTICS
(a) The operation distance varies according to how customers hold the transmitter or where it is used.
(b) Strong external radio waves or other frequency noise may interfere with the Remote Engine
Starter’s operation distance.
REMOTE ENGINE STARTER BASIC FUNCTIONS
(a) Stand on the driver’s side, three feet away from the vehicle.
(b) Turn the transmitter toward the vehicle and press and release the LOCK button twice within two
seconds. Immediately press and hold the LOCK button for three seconds. The hazard lights flash
after three seconds.
(c) The engine then starts, and the hazard lights flash for 20 seconds.
(d) Press the UNLOCK button. The engine stops and hazard lights flash twice.
OR
Press and hold the LOCK button for two or more seconds. The engine stops and the hazard lights
flash once.
MPX
ST1I
P
RDIG
OPI2
LDUT
OP13
(DSWH)
STSW
OB2I
+B
IGI
-
ST10
-
GND
GND
-
-
OB20
Part Number: 90980-12258
Color: White
MALE FRONT VIEW MALE FRONT VIEW
Part Number: 90980-11361
Color: White
Remote Engine Starter Troubleshooting Guide Page 4
RES ECU PIN LAYOUT
<Connector>
9
10 8 7 6 5 4 3 2 1
20 19 18 17 16 15 14 13 12 11
12
8 7 6 5 4 3
*1: Vehicles without Push Start System only.
*2: Vehicles with Push Start System only.
Terminal
N
o.
Content Signal
1 MPX Signal
2 ST1 Input *1
3 SHIFT P
4 RES Diag
5 OPTIONINPUT2
6 CHECK ENGINE
LIGHT
7 OPTIONINPUT3
8 (HOOD SW.)
9 STSW Signal *2
10 OBD2 (Diag.) *1
11 +B
12 IG1
13 N.C.
14 ST1 Output *1
15 N.C.
16 GND
17 GND
18 N.C.
19 N.C.
20 OBD2 (Imm. ECU) *1
Terminal
N
o.
Content Signal
1 AM1 *1
2 AM2 *1
3 IGI *1
4 N.C.
5 ACC *1
6 ST2 *1
7 N.C.
8 IG2 *1
AM1
AM2
IG1
-
ACC
ST2
-
IG2
Remote Engine Starter Troubleshooting Guide Page 5
RES ECU TERMINALS
Remote Engine Starter ECU Input/Output Specifications
Signal Symbol I/O Condition
+B +B ECU+B 12V (TYP)
GND E ECU GND 0 V
AM1 *1 AM1 Input
AM2 *1 AM2 Input
IG1 *1 IG1 Output
IG2 *1 IG2 Output
ACC *1 ACC Output
ST2 *1 ST2 Output
Dropping voltage: Less than 0.2V
IG1
(same terminal
as above)
IG1 Input ON : Over (+B-1) V
Hood SW DSWH Input Close : Less than 1V
Shift position P P Input ON : Over (+B-1) V
Check engine
lamp
LDUT Input OFF : Less than 2.2V
ON : Over 6V
Diagnosis
communication1
*1
OB2I Input Pulse generation during communication
Diagnosis
communication2
*1
OB2O Output Pulse generation during communication
BEAN
communication
MPX Commu-
nication
Pulse generation
ST1(IN) *1 ST1I Input ON : Over (+B-1)V
ST1(OUT) *1 ST1O Output Permissible current : 500mA
STSW *2 STSW Output ON : Over (+B-2) V
Remote engine
starter diagnosis
input
RDIG Input ON : Less than 1V
*1: Vehicles without Push Start System only.
*2: Vehicles with Push Start System only.
Part Number: 90980-10798
Color: Dark gray
MALE FRONT VIEW
Remote Engine Starter Troubleshooting Guide Page 6
ACCESSORY GATEWAY ECU PIN LAYOUT
<Connector>
ACCESSORY GATEWAY ECU TERMINALS
Accessory gateway ECU Input/Output Specifications
Signal Symbol I/O Condition
+B +B ECU+B 12V (TYP)
GND E ECU GND 0 V
MPX signal for
accessory
MPXY Commu-
nication
MPX signal for
Vehicle LAN
MPX Commu-
nication
Pulse generation
5 4 3 2 1
Terminal No. Content Signal
1 MPX Signal for Accessory MPXY
2 N.C. _
3 +B +B
4 GND GND
5 MPX Signal for Vehicle MPX
Remote Engine Starter Troubleshooting Guide Page 7
HOW TO PROCEED WITH TROUBLESHOOTING
HINT
zUse these procedures to troubleshoot the Remote Engine Starter.
zThe hand-held tester should be used in Step 4.
1 VEHICLE BROUGHT IN FOR SERVICE
2 CUSTOMER PROBLEM ANALYSIS CHECK AND SYMPTOM CHECK
3 PROBLEM SYMPTOMS TABLE
4 OVERALL ANALYSIS AND TROUBLESHOOTING
(a) Diagnostic Mode check, if necessary (see page 10)
(b) Check ECU terminals (see pages 4 to 6)
(c) Check wire harness (see I/I and EWD)
5 Please fax the Replacement Authorization Request Sheet and Customer Problem Analysis
Check Sheet to (800) 438-5410 to receive an RES Authorization Number.
For assistance, please call Fujitsu Ten Technical Support at (800) 237-5413.
7 CONFIRMATION TEST
END
6 CHECK INSTALLATION AND PROGRAMING, REPAIR OR REPLACE
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
Remote Engine Starter Troubleshooting Guide Page 8
CUSTOMER PROBLEM ANALYSIS CHECK
Today’s date:_____________ __
Customer’s Name R.O. No.
Problem Conditions Verified Unable to verify
Date Problem First Occurred (M) /(D) / (Y)
Where did the problem occur? Home Work Other
How far from the user was the car? Less than 5 feet 5 to 10 feet
10 to 30 feet More than 30 feet
When did the problem occur? After car repaired After engine stalled
After other accesorry installed
After change to new car key or transmitter
How often has the problem occurred? Always Sometimes
Once only
Weather Clear Cloudy Rainy Snowy
Various/Other
Weather Conditions
When Problem
Occurred Outdoor
Temperature
Hot Warm Cool Very Cold
Approx. Deg F
Customer Complaint (After completing inspection, please select one from below, or choose “other” if not applicable.)
Engine did not start (1) Was the Immobilizer code registration confirmed?
Yes No
(2) How many times did the hazard lights flash in
Diagnostic Mode? ____ times
Engine stopped unexpectedly (1) Was the total run time under 20 minutes?
Yes No
(2) How many times did the hazard lights flash in
Diagnostic Mode? ____ times
Engine did not stop (1) What condition was present when the problem occurred?
LOCK button pressed and held UNLOCK button pressed
Engine ran more than 10 min. Hood was open
Key was in ignition or push start button was pressed
“Check Engine” light came on
Other ________________________________________
Other (Please explain in detail)
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
REMOTE ENGINE STARTER SYSTEM Check Sheet
Remote Engine Starter Troubleshooting Guide Page 9
PROBLEM SYMPTOMS TABLE
Symptom Check item See page
Engine does not start by
remote.
1. Remote keyless entry operation
2. Engine operation
3. Remote E/G start operation
4. Remote Engine Starter diagnosis
5. Vehicle circuit (Engine Starter ECU
input/output check)
6. Immobilizer ID code registration
13
Engine does not stop by
remote.
1. Remote keyless entry operation
2. Remote E/G stop operation
3. Vehicle circuit (Engine Starter ECU
input/output check)
16
Engine stops unexpectedly. 1. Total operation time (Run time)
2. Remote Engine Starter Diagnosis
3. Vehicle circuit (Engine Starter ECU
input/output check)
18
Registration of ID code of
Immobilizer failed.
1. Immobilizer ID code registration
operation
2. Vehicle circuit (Engine Starter ECU
input/output check)
20
Remote Engine Starter Troubleshooting Guide Page 10
DIAGNOSTIC OPERATION
ENGINE STARTER DIAGNOSIS
NOTE: Turn the engine off before performing any diagnostic function.
The Diagnostic Mode can help determine why the engine stops/fails.
To set the Diagnostic Mode, you must locate and connect the Diagnostic Connectors (RDIG).
To do so, follow the steps below:
(1) Remove the passenger side step cover.
(2) Remove the passenger side cowl cover.
(3) Find and connect the Diagnostic Connectors (RDIG) with label, located in the passenger
cowl area.
RES
Diagnostic
Connectors
These
connectors
must be
connected.
Cowl Cover
Nut
Ste
p
Cover
Andere Handbücher für TVIP V4
1
Inhaltsverzeichnis
Andere Toyota Fernstartsystem Handbücher
Toyota
Toyota RS3200 PLUS Bedienungsanleitung
Toyota
Toyota 2008 SEQUOIA Bedienungsanleitung
Toyota
Toyota TVIP V4 Bedienungsanleitung
Toyota
Toyota PT398-47091 Bedienungsanleitung
Toyota
Toyota 00016-32901 Bedienungsanleitung
Toyota
Toyota PT398-02080 Bedienungsanleitung
Toyota
Toyota PT398-42130 Konfigurationshandbuch
Toyota
Toyota PT398-60080 Bedienungsanleitung
Toyota
Toyota PT398-00100 Bedienungsanleitung
