TP-Link TL-PA211KIT Bedienungsanleitung

TL-PA211

AV200 Mini Powerline Adapter

Rev: 1.0.0

1910010392

Specifications are subject to change without notice. is a registered trademark of

TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered

trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any

derivative such as translation, transformation, or adaptation without permission from TP-LINK

reserved.

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could

void the user‟s authority to operate the equipment.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which

case the user may be required to take adequate measures.

III

Important Safety Instructions

1. Do Not open this product or attempt to service this product, it may expose you to dangerous high

voltage and other risks.

2. Do Not operate this product near water.

3. Do Not place or operate near or over radiator or heat register.

4. Do Not expose this product to dampness, dust or corrosive liquids.

5. Do Not connect this product and Disconnect from wall socket during a lightning or thunderstorm

6. Do Not obstruct this product ventilation slots, as insufficient airflow may harm this product.

7. Do Not put anything on this product.

8. Plug directly into wall socket (100Vac~240Vac). Do Not use an extension cord between this product

and the AC power source.

9. When plugging this product into wall socket, make sure that electrical socket are not damaged, and

no leakage for gas or water pipes to begin with.

10. Place the connecting cables carefully so people won‟t stumble or walk on it.

11. The Powerline Adapter should be operated from the type of power indicated on the marking label. If

you are not sure of the type of power available, consult the qualified technician.

12. Unplug the Powerline Adapter from the mains and refer the product to qualified service personnel for

the following conditions:

If liquid has been spilled on the product

If the product has been exposed to rain or water

13. Unplug from the wall socket before cleaning. Use a damp cloth for cleaning. Do not use liquid

cleaners or aerosol cleaners.

14. The specification of the fuse is T2.5AL250V. To avoid damage, please do not change the fuse.

15. The Operating temperature is 0℃~42℃(32℉~107.6℉).

16. The Storage temperature is -40℃~70℃(-40℉~158℉).

CONTENTS

Chapter 1 Introduction..................................................................................................... 1

Chapter 2 Connecting Mechanism.................................................................................. 2

2.1 Introduction ............................................................................................................. 2

2.2 LED Indicator .......................................................................................................... 2

2.3 Physical Interface.................................................................................................... 3

2.4 Hardware Connection –Computer.......................................................................... 4

2.5 Hardware Connection –Internet ............................................................................. 4

Chapter 3 Installing Management Utility......................................................................... 6

Chapter 4 Using The Management Utility..................................................................... 10

4.1 Main ...................................................................................................................... 10

4.1.1 Rename........................................................................................................ 12

4.1.2 Enter Password............................................................................................. 13

4.1.3 Add Device.................................................................................................... 14

4.1.4 Reset ............................................................................................................ 15

4.2 Privacy .................................................................................................................. 15

4.3 QoS....................................................................................................................... 16

4.4 Diagnostics............................................................................................................ 17

4.5 About..................................................................................................................... 19

Chapter 5 Advance Feature: How to Use the Push buttons ....................................... 20

5.1 Pair( Secure with 128 bits-AES)............................................................................ 20

5.2 Set Up a PowerlineAV Network with the Pair button............................................. 20

Chapter 6 Appendix A: Troubleshooting Guide........................................................... 22

TL-PA211

AV200 Mini Powerline Adapter

Chapter 1 Introduction

Congratulations on your purchase of this outstanding Mini Powerline Adapter. This device is an AV200

Mini Powerline Adapter which transforms your house‟s existing electrical wiring into an ubiquitous

networking infrastructure. Simply plug this AV200 Mini Powerline Adapter into an ordinary AC power

outlet which will easily extend your Cable/xDSL broadband connection or existing Ethernet (LAN)

network to any other electrical outlet in any room of a house without the need of any new cabling.

This Mini PowerlineAdapter supports up to 200Mbps data rate over the existing household power circuit.

With data rates of 200Mbps, full multimedia application can easily be supported throughout the whole

house in addition to Internet access. This Mini Powerline Adapter uses the existing power lines installed

in a home as a path to transmit digital data, voice, audio and video between devices.

To ensure data communication‟s security and multimedia applications, this Mini Powerline Adapter

support built-in 128-bit AES encryption and Quality of Service (QoS) features.With minimum setup, you

can install and use this Mini Powerline Adapter within minutes. The adapter adds two useful functions.

1．Existing connection with a new unassociated device added via the Pair button.

2．Reset to default setting via the Management Utility.

A. System Requirement

a) At least twoAC 100V ~ 240V power outlets with standard home power wiring

b) A computer with the following:

Operating System with TCP/IP installed

Pentium III compatible processor and above

Ethernet LAN card installed with TCP/IP protocol

64 MB RAM or more

50 MB of free disk space (Minimum)

CD-ROM Drive

B. Package Contents

TheAV200 Mini PowerlineAdapter package contains the following items:

OneAV200 Mini Powerline Adapter (There are twoAV200 Mini PowerlineAdapters in Starter Kit)

One CAT-5 Ethernet Cable (There are two CAT-5 Ethernet Cables in Starter Kit)

One Quick Installation Guide

One CD-ROM (Utility / Manual / Quick Installation Guide/Acrobat Reader)

If any of the above items are damaged or missing, please contact your dealer immediately.

TL-PA211

AV200 Mini Powerline Adapter

Chapter 2 Connecting Mechanism

2.1 Introduction

The Mini Powerline Adapter supports up to 200Mbps data rate. With this high speed connection rate,

this Mini Powerline Adapter allows you to setup a high speed home network by using your home existing

electrical wiring. Simply plug this Mini Powerline Adapter into an ordinary power outlet to extend your

Cable/xDSLbroadband connection or existing LAN network to any other electrical outlet in any rooms of

your house.

Take notes that this Mini Powerline Adapter works in pairs. You need to plug one Mini Powerline Adapter

into a power outlet for each computer (Connect to the computer LAN card) you want to connect

(Network access); you will also need another Mini Powerline Adapter connected to your Cable/xDSL

broadband (Ethernet port) in order to extend your broadband connection or Internet surfing. With clean

powerline, the distance between two Mini Powerline Adapters can reach 300 meters at lease, but the

actual distance may vary due to the environment.

Section below describes the Mini Powerline Adapter‟s LED indicators, physical interface and hardware

connection mechanism.

2.2 LED Indicator

The LED indicator displays information about the device‟s status.

Item

Status

Indication

Power LED

Off

Power is off.

Power is on.

Flashing

The Adapter is in power-saving Mode.

Powerline LED

Off

The Adapter has not connected to Powerline network or

is in power-saving Mode.

TL-PA211

AV200 Mini Powerline Adapter

The Adapter has connected to a Powerline network.

Flashing

The Adapter is transmitting or receiving data.

Ethernet LED

Off

The Ethernet port is not connected to a device or the

device is power off.

The Ethernet port is linked, but there is no activity.

Flashing

Data is being transmitted through the Ethernet port

Note:

5 minutes later since the device connected to the Homeplug is powered off, the Homeplug will switch to

Power-saving Mode automatically.

2.3 Physical Interface

There are four physical interfaces on this Mini PowerlineAdapter.

Interface

Description

Ethernet

One 10/100Mbps Ethernet port connected to PC LAN card or broadband

device

Power Plug

Power Plug connected to any 100V ~ 240VAC power socket

Pair

Press and hold the Pair button for about 3 to 8 seconds, then release it. The

Power LED will begin flashing.

Note:

1. If you press the Pair button for more than 10 seconds, the Powerline Adapter will leave the network

which it is associated with and its network name assumes a random value. The Power LED turns off

when it disconnects from the Powerline network.

2. For detail information about the Pair button, please refer to Charpter 5 Advanced Feature:How to

TL-PA211

AV200 Mini Powerline Adapter

Use the Push buttons

2.4 Hardware Connection –Computer

For those computers you wish to be networked by Mini Powerline Adapter, each of the computers must

be properly connected with a Mini Powerline Adapter through an Ethernet (RJ-45) cable.

Following are the steps to properly connect the Mini PowerlineAdapter to your computer:

1．Connect the provided Ethernet (RJ-45) cable to the Mini Powerline Adapter‟s Ethernet port.

2．Connect the other end of the Ethernet (RJ-45) cable to you computer‟s LAN port.

3．Plug the Mini PowerlineAdapter into a wall socket next to the computer.

4．Turn on your computer.

5．Check and confirm that the Power LED and Ethernet LED on the Mini Powerline Adapter

are ON.

The hardware connection mechanism is shown below:

2.5 Hardware Connection –Internet

This section describes how to connect the Mini Powerline Adapter into your existing ADSL broadband

connection viaADSL Ethernet port. Follow the procedures describe below to connect the Mini Powerline

Adapter to yourADSL broadband connection:

1．Connect the provided Ethernet (RJ-45) cable to the Mini Powerline Adapter‟s Ethernet port.

2．Connect the other end of the Ethernet (RJ-45) cable to an available Ethernet port of your ADSL

broadband Router.

3．Plug the Mini PowerlineAdapter into a wall socket next to the computer.

4．Turn on your computer.

5．Check and confirm that the Power LED, Ethernet LED, and Powerline LED on the

Mini Powerline Adapter are ON.

TL-PA211

AV200 Mini Powerline Adapter

The hardware connection mechanism is shown below:

Note:

Do not connect the Powerline adapter to an extension lead, power strip, extension cord, surge protector

as this may degrade the network performance.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TP-Link Adapter Handbücher

TP-Link

TP-Link TG-3468 Bedienungsanleitung

TP-Link

TP-Link TL-PA4030 Bedienungsanleitung

TP-Link

TP-Link TL-WA860RE Bedienungsanleitung

TP-Link

TP-Link TL-WDN4200 Bedienungsanleitung

TP-Link

TP-Link Archer TX20U Plus Bedienungsanleitung

TP-Link

TP-Link TF-5239 Bedienungsanleitung

TP-Link

TP-Link TL-WN851ND Bedienungsanleitung

TP-Link

TP-Link Archer T2U Bedienungsanleitung

TP-Link

TP-Link AV500 Bedienungsanleitung

TP-Link

TP-Link TL-WN721N Bedienungsanleitung

TP-Link

TP-Link TL-WDN3200 Bedienungsanleitung

TP-Link

TP-Link Archer T2E Bedienungsanleitung

TP-Link

TP-Link TG-3468 V4 Bedienungsanleitung

TP-Link

TP-Link TL-PA7019P Bedienungsanleitung

TP-Link

TP-Link TL-WN951N - IEEE 802.11b/g 802.11n Draft 2.0 PCI Wireless... Bedienungsanleitung

TP-Link

TP-Link TL-PA2010 Bedienungsanleitung

TP-Link

TP-Link AV1000 Bedienungsanleitung

TP-Link

TP-Link UB400 Bedienungsanleitung

TP-Link

TP-Link TL-WN951N - IEEE 802.11b/g 802.11n Draft 2.0 PCI Wireless... Bedienungsanleitung

TP-Link

TP-Link Omada POE2412G Bedienungsanleitung

TP-Link

TP-Link TL-PA511 Bedienungsanleitung

TP-Link

TP-Link TL-PA210 Bedienungsanleitung

TP-Link

TP-Link TL-WN881ND Bedienungsanleitung

TP-Link

TP-Link Archer T3U Plus Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung