TP-Link JetStream T2600G-28TS Bedienungsanleitung

Installation Guide

Gigabit L2 Managed Switch

T2600G-28TS (TL-SG3424)

T2600G-52TS (TL-SG3452)

Business Networking Solution

Specifications are subject to change without notice. is a registered trademark of TP-LINK

TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such

as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

CE Mark Warning

This is a class A product. In a domestic environment, this product may cause radio interference, in which case the

user may be required to take adequate measures.

II Related Document

Related Document

The User Guide and CLI Reference Guide of the product are provided on the resource

CD.

To obtain the latest product information, please visit the official website:

http://www.tp-link.com

About this Installation Guide

This Installation Guide describes the hardware characteristics, installation methods and

the points that should be attended to during installation.

This Installation Guide is structured as follows:

Chapter 1 Introduction. This chapter describes the external components of the

switch.

Chapter 2 Installation. This chapter illustrates how to install the switch.

Chapter 3 Lightning Protection. This chapter illustrates how to prevent lightning

damage.

Chapter 4 Connection. This chapter illustrates how to do the physical connection of

the switch.

Chapter 5 Configuration. This chapter instructs you to configure the switch via Web

Interface and CLI commands.

Appendix A Troubleshooting.

Appendix B Hardware Specifications.

III

Audience

This Installation Guide is for:

Network Engineer

Network Administrator

Conventions

Due to the similarity in the structure of the L2 Managed Switch series, in this Installation

Guide we take T2600G-28TS as an example to illustrate Chapter 2 Installation, Chapter

3 Lightning Protection and Chapter 4 Connection.

This guide uses the specific formats to highlight special messages. The following table

lists the notice icons that are used throughout this guide.

Remind to be careful. A caution indicates a potential which may

result in device damage.

Remind to take notice. The note contains the helpful

information for a better use of the product.

Audience

Contents

Chapter 1 Introduction ———————————— 01

1.1 Product Overview.........................................01

1.2 Appearance .................................................01

Chapter 2 Installation ————————————— 05

2.1 Package Contents.........................................05

2.2 Safety Precautions........................................05

2.3 Installation Tools ..........................................07

2.4 Product Installation ......................................07

Chapter 3 Lightning Protection ———————— 09

3.1 Cabling Reasonably ......................................09

3.2 Connect to Ground .......................................11

3.3 Equipotential Bonding...................................12

3.4 Use Lightning Arrester ..................................13

Chapter 4 Connection ————————————— 14

4.1 Ethernet Port ...............................................14

4.2 SFP Port ......................................................14

4.3 Console Port ................................................15

4.4 Verify Installation .........................................16

4.5 Power On ..................................................17

4.6 Initialization.................................................17

Chapter 5 Configuration———————————— 18

5.1 Configure the Switch via GUI ........................18

5.2 Configure the Switch Using CLI .....................19

Appendix A Troubleshooting—————————— 22

Appendix B Hardware Specifications —————— 24

Gigabit L2 Managed Switch

Introduction

Chapter 1 Introduction

1.1 Product Overview

T2600G-28TS and T2600G-52TS are Gigabit Ethernet switching products recently

developed by TP-LINK. T2600G-28TS possesses 24 RJ45 ports and 4 SFP slots, while

T2600G-52TS characterizes with 48 RJ45 ports and 4 SFP slots. The SFP slot enables

remote connection with SFP slots on other devices through SFP module and fiber.

T2600G-28TS/T2600G-52TS is compatible with all kinds of gigabit SFP modules. Here

you are recommended to choose gigabit SFP module produced by TP-LINK, which can

perfectly extend your network and enlarge the bandwidth. T2600G-28TS/T2600G-52TS

is your first choice to extend the originally large and medium-sized network.

Designed for workgroups and departments, T2600G-28TS/T2600G-52TS from TP-LINK

provides wire-speed performance and full set of L2 management features. It provides a

variety of service features and multiple powerful functions with high security.

The EIA-standardized framework and smart configuration capacity can provide flexible

solutions for a variable scale of networks. ACL, 802.1x and Dynamic ARP Inspection

provide robust security strategies. QoS and IGMP snooping/filtering optimize voice and

video application. Link aggregation (LACP) increases aggregated bandwidth, optimizing

the transport of business critical data. SNMP, RMON, WEB and CLI Log-in bring

abundant management policies. TP-LINK JetStream L2 Managed Switch integrates

multiple functions with excellent performance, and is friendly to manage, which can

fully meet the need of the users demanding higher networking performance.

1.2 Appearance

■Front Panel

The front panel of T2600G-28TS is shown as the following figure.

T2600-28TS

LEDs

10/100/1000 Mbps RJ45 Port

Console (RJ-45)

Console (USB)

SFP Port

Figure 1-1 Front Panel of T2600G-28TS

LEDs

LED Status Indication

PWR

On The switch is powered on.

Off The switch is powered off or power supply is abnormal.

Flashing Power supply is abnormal.

SYS Flashing The switch works properly.

On/Off The switch works improperly.

Gigabit L2 Managed Switch

Introduction

LED Status Indication

1000Mbps On A device is linked to the corresponding port and running at 1000Mbps.

Off A 10/100Mbps device or no device is linked to the corresponding port.

Link/Act

On A device is linked to the corresponding port and running properly.

Flashing Data is being transmitted or received.

Off No device is linked to the corresponding port.

Console (RJ-45) Port

Designed to connect with the serial port of a computer or terminal for monitoring

and configuring the switch.

Console (USB) Port

Designed to connect with the USB port of a computer for monitoring and configuring

the switch. The switch has an RJ-45 console port and a micro-USB console port

available. Console input is active on only one console port at a time. By default, the

micro-USB connector takes precedence over the RJ-45 connector.

10/100/1000Mbps RJ45 Port

Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or

1000Mbps. Each 10/100/1000Mbps RJ45 port has a corresponding 1000Mbps LED

and Link/Act LED.

SFP Port

Designed to install the SFP module. T2600G-28TS features 4 individual SFP ports

and supports 1000M SFP module connection only.

The front panel of T2600G-52TS is shown as the following figure.

ConsoleConsole(USB)

Console (USB)

10/100/1000Mbps RJ45 Port

Console (RJ-45)

LEDs

SFP Port

Figure 1-2 Front Panel of T2600G-52TS

Console (USB) Port

Designed to connect with the USB port of a computer for monitoring and configuring

the switch. The switch has an RJ-45 console port and a micro-USB console port

available. Console input is active on only one console port at a time. By default, the

micro-USB connector takes precedence over the RJ-45 connector.

Console (RJ-45) Port

Designed to connect with the serial port of a computer or terminal for monitoring

and configuring the switch.

Gigabit L2 Managed Switch

Introduction

LEDs

LED Status Indication

PWR

On The switch is powered on.

Off The switch is powered off or power supply is abnormal.

Flashing Power supply is abnormal.

SYS Flashing The switch works properly.

On/Off The switch works improperly.

10/100/

1000Mbps

(Port 1-48)

Green

On A 1000Mbps device is linked to the corresponding port,

but no activity.

Flashing A 1000Mbps device is linked to the corresponding port

and data is being transmitted or received.

Yellow

On A 10/100Mbps device is linked to the corresponding

port, but no activity.

Flashing A 10/100Mbps device is linked to the corresponding port

and data is being transmitted or received.

Off No device is linked to the corresponding SFP port but

no activity.

Link/Act

(Port 49-52)

There is a device linked to the corresponding port.

Flashing

The corresponding SFP port is transmitting or receiving

data.

Off There is no device linked to the corresponding SFP port.

10/100/1000Mbps RJ45 Port

Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or

1000Mbps. Each 10/100/1000Mbps RJ45 port has a corresponding 1000Mbps LED.

SFP Port

Designed to install the SFP module. T2600G-52TS features 4 individual SFP ports

and supports 1000M SFP module connection only.

Port Feature

Model 10/100/1000Mbps RJ45 Port SFP Port Console Port

T2600G-28TS 24 4 2

T2600G-52TS 48 4 2

■Rear Panel

Due to the similarity of T2600G-28TS and T2600G-52TS in the rear panel, here

T2600G-28TS is used as an example.

100-240V~50/60Hz 0.5A

Grounding Terminal

Kensington Security Slot

Power Socket

Figure 1-3 Rear Panel of T2600G-28TS

Gigabit L2 Managed Switch

Introduction

Kensington Security Slot

Secure the lock (not provided) into the security slot to prevent the device from being

stolen.

Grounding Terminal

The switch already comes with lightning protection mechanism. You can also ground

the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable.

For detailed information, please refer to Chapter 3 Lightning Protection.

Power Socket

Connect the female connector of the power cord here, and the male connector to

the AC power outlet. Please make sure the voltage of the power supply meets the

requirement of the input voltage (100-240V~ 50/60Hz).

Caution: Please use the provided power cord.

Andere Handbücher für JetStream T2600G-28TS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TP-Link Netzwerk-Router Handbücher

TP-Link

TP-Link Omada ER706W Bedienungsanleitung

TP-Link

TP-Link TD-W8961ND Bedienungsanleitung

TP-Link

TP-Link TL-WA830RE Bedienungsanleitung

TP-Link

TP-Link Wi-Fi 7 Bedienungsanleitung

TP-Link

TP-Link RE200 Bedienungsanleitung

TP-Link

TP-Link TX-6610 Bedienungsanleitung

TP-Link

TP-Link Archer C7 Bedienungsanleitung

TP-Link

TP-Link SafeStream TL-ER5120 Bedienungsanleitung

TP-Link

TP-Link TD-8816B Bedienungsanleitung

TP-Link

TP-Link TD-W8968 Bedienungsanleitung

TP-Link

TP-Link Archer AC1200 Bedienungsanleitung

TP-Link

TP-Link Archer MR400 Bedienungsanleitung

TP-Link

TP-Link TL-WR843N Bedienungsanleitung

TP-Link

TP-Link TD-8800 Bedienungsanleitung

TP-Link

TP-Link TD-8840T Bedienungsanleitung

TP-Link

TP-Link TL-WR841N Bedienungsanleitung

TP-Link

TP-Link TL-WR940N Bedienungsanleitung

TP-Link

TP-Link Deco XE200 Bedienungsanleitung

TP-Link

TP-Link Deco X10 Bedienungsanleitung

TP-Link

TP-Link ARCHER C3150 Bedienungsanleitung

TP-Link

TP-Link Archer VR600 Bedienungsanleitung

TP-Link

TP-Link TL-WR802N Bedienungsanleitung

TP-Link

TP-Link TD-W300KIT Bedienungsanleitung

TP-Link

TP-Link TL-ER7206 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung