TP-Link TL-WR703N Bedienungsanleitung
Quick Installation Guide for TL-WR703N
Wireless Nano AP Router Pre-Installed with DD-WRT
Firmware
Table of Contents:
1. Basic Information
1.1 Basic Product Log In information
1.2 Important Notice
2. Quick Installation
2.1 Hardware Installation
2.2 Setup you Computer
2.3 Connect your Computer to TL-WR703N
2.4 Configuration on TL-WR703N
2.4.1 Log In to TL-WR703N
2.4.2 Select Your Language
2.4.3 Dial Up
2.5 Visit Internet (Connect your PC to TL-WR703N Again)
2.6 Wireless Encryption
3. Advanced Configuration
Quick Installation Guide for TL-WR703N
1. Basic Information
1.1 Basic Product Log In information
1.1.1 Log in Information
You can log into the interface of this Nano WIFI router with the
following information:
IPAddress: 192.168.1.1
User Name: admin
Pass Word: admin
1.2 Important Notice
1.2.1 We are responsible for the quality warranty if this product
comes at DOA (Death On Arrival) Status.
1.2.2 This product is pre-installed with current version of DD-WRT
firmware, you are able to setup WIFI wireless broadband network
with this device based on the current firmware. If you have any
questions for using this router, please feel free to contact us.
1.2.3 DD-WRT is an open sourced, editable, continual upgradable
third party firmware. We are not responsible for the quality problem
caused by upgrading this router with other version of DD-WRT
firmware by the buyer/end-users himself/herself.
2. Quick Installation
2.1 Hardware Installation
2.1.1 Basic requirement for installation:
PC
WIFI Wireless Adapter
IE Internet Explorer
Ethernet Cable
Power Supply
2.1.2 Connect the Cables and Power Supply
Step 1: Connect one end of the provided USB cable to micro USB
port of TL-WR703N.
Step 2: Connect the other end of the provided USB cable to the
power adapter or the USB Port of your PC.
Step 3: Plug in standard electrical wall socket directly to power the
Router.
Step 4: For AP Mode and Router Mode, connect the LAN/WAN port
of TL-WR703N to Internet with an Ethernet cable.
2.1.3 Interface Introduction
Below is a photo of the interface of your wireless router
LAN/WAN: This port works as WAN in AP Router mode.
Power: This port is used to connect the provided power adapter.
Reset：It is used to reset the TL-WR703N to its factory defaults.
How to reset this wireless router?
Please use a small pin to press this reset button and hold it for 5~7
seconds. After this, your router is reset.
Notice: Please note that after reset, all your information stored in
the router will be removed and you need to configure your router
again.
2.1.4 LED Indications
The LED blinks for 1~2 times when you give power supply to the
Router.
After this, the LED is not on. This is Normal because the router is
installed with DD-WRT firmware.
For checking if this router is workable or not, please disconnect the
power supply to the router and give power supply to it again. If the
LED blinks 1~2 times when you plug on the power supply to it, it
means the router is workable.
2.2 Setup you Computer
Note: Here we take Windows 7 as example.
2.2.1 On your PC, Go to Start > Control Panel > View network
status and tasks > Change adapter settings. Right click
"Wireless Network Connection", and select "Properties".
2.2.2 Double click Internet Protocol Version 4 (TCP/IPv4) in the
item list.
2.2.3 Select “Obtain an IP address automatically” and select
“Obtain DNS server address automatically” and then click “OK”
2.3 Connect your Computer to TL-WR703N
Below we will tell you how to connect your PC to your wireless
router wirelessly, please make sure that your PC has wireless
adapter.
2.3.1 Please note that the default SSID of your wireless router is
“dd-wrt”, this wireless router is default as no wireless
encryption.
2.3.2 Click the wireless icon at the bottom of your
desktop. Click refresh button, and then select the default
SSID of " dd-wrt" and then Click “Connect”
2.3.3 If you can see Connected as shown in the screen below,
you’ve successfully connected to the wireless network.
2.4 Configuration on TL-WR703N
2.4.1 Log In to TL-WR703N
Step 1:
Please open your Internet Explorer, in the place of address bar
please input “192.168.1.1” and then click “Enter”.
Step 2:
At the screen below, enter the default User Name and Password:
admin, both in lower case letters. Then Click OK.
Step 3:
You would see the screen below:
2.4.2
Here it is in English interface, you can select other languages.
Please click “Administration” as below.
Please select your language as below:
At the bottom of the interface, please click “Save”, and then click
“Apply Settings”.
Inhaltsverzeichnis
Andere TP-Link Netzwerk-Router Handbücher
TP-Link
TP-Link Deco X50-4G Bedienungsanleitung
TP-Link
TP-Link Deco W6000 Bedienungsanleitung
TP-Link
TP-Link TD-8811 Bedienungsanleitung
TP-Link
TP-Link TL-R470T+ Bedienungsanleitung
TP-Link
TP-Link Archer C3200 Bedienungsanleitung
TP-Link
TP-Link AXE5400 Bedienungsanleitung
TP-Link
TP-Link TD-W8961ND Bedienungsanleitung
TP-Link
TP-Link Archer C6 Bedienungsanleitung
TP-Link
TP-Link SafeStream TL-R600VPN Bedienungsanleitung
TP-Link
TP-Link WR841HPV5 Bedienungsanleitung
TP-Link
TP-Link TL-WR840N Bedienungsanleitung
TP-Link
TP-Link TD-8810 Bedienungsanleitung
TP-Link
TP-Link Archer VR600v Bedienungsanleitung
TP-Link
TP-Link ARCHER C3150 Bedienungsanleitung
TP-Link
TP-Link TL-R470T+ Bedienungsanleitung
TP-Link
TP-Link TL-ER604W Bedienungsanleitung
TP-Link
TP-Link HC220 Bedienungsanleitung
TP-Link
TP-Link TL-R470T Bedienungsanleitung
TP-Link
TP-Link TL-WR802N Bedienungsanleitung
TP-Link
TP-Link ARCHER MR200 Bedienungsanleitung
