Trane 4TTR4018-060 Bedienungsanleitung

18-AC51D1-10E-EN

ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES

IMPORTANT — This Document is customer property and is to remain with this unit. Please return to service informa-

tion pack upon completion of work.

Condensing Units

These instructions do not cover all variations in systems or provide for every possible contingency to be met in connection with

the installation. Should further information be desired or should particular problems arise which are not covered sufficiently for the

purchaser’s purposes, the matter should be referred to your installing dealer or local distributor.

Note: The manufacturer recommends installing only approved matched indoor and outdoor systems. Some of the benefits of

installing approved matched indoor and outdoor split systems are maximum efficiency, optimum performance and the best overall

system reliability.

4TTR4018 – 060

Table of Contents

Section 1. Safety..................................................................................... 2

Section 2. Unit Location Considerations ............................................. 3

Section 3. Unit Preparation.................................................................... 5

Section 4. Setting the Unit..................................................................... 5

Section 5. Refrigerant Line Considerations......................................... 6

Section 6. Refrigerant Line Routing ..................................................... 7

Section 7. Refrigerant Line Brazing...................................................... 8

Section 8. Refrigerant Line Leak Check............................................. 10

Section 9. Evacuation .......................................................................... 11

Section 10. Service Valves .................................................................. 11

Section 11. Electrical - Low Voltage ................................................... 12

Section 12. Electrical - High Voltage .................................................. 15

Section 13. Start Up.............................................................................. 16

Section 14. System Charge Adjustment............................................. 17

Section 15. Checkout Procedures ...................................................... 23

Section 16. Refrigerant Circuits.......................................................... 23

Section 17. Wiring Diagrams............................................................... 26

Section 18. Pressure Curves............................................................... 36

Installation and Operation Manual

2 18-AC51D1-10E-EN

Section 1. Safety

WARNING

This information is intended for use by individuals

possessing adequate backgrounds of electrical and

mechanical experience. Any attempt to repair a central

air conditioning product may result in personal injury

and/or property damage. The manufacture or seller

cannot be responsible for the interpretation of this

information, nor can it assume any liability in connec-

tion with its use.

These units use R-410A refrigerant which operates

at 50 to 70% higher pressures than R-22. Use only

R-410A approved service equipment. Refrigerant

cylinders are painted a “Rose” color to indicate the

type of refrigerant and may contain a “dip” tube to

allow for charging of liquid refrigerant into the sys-

tem. All R-410A systems use a POE oil that readily

absorbs moisture from the atmosphere. To limit this

“hygroscopic” action, the system should remain sealed

whenever possible. If a system has been open to the

atmosphere for more than 4 hours, the compressor oil

must be replaced. Never break a vacuum with air and

always change the driers when opening the system

for component replacement. For specific handling

concerns with R-410A and POE oil reference Retrofit

Bulletins SS-APG006-EN and APP-APG011-EN or

APP-APG012-EN.

Extreme caution should be exercised when opening

the Liquid Line Service Valve. Turn counterclockwise

until the valve stem just touches the rolled edge. No

torque is required. Failure to follow this warning will

result in abrupt release of system charge and may

result in personal injury and /or property damage.

UNIT CONTAINS R-410A REFRIGERANT!

R-410A operating pressures exceed the limit of R-22.

Proper service equipment is required. Failure to use

proper service tools may result in equipment damage

or personal injury.

SERVICE

USE ONLY R-410A REFRIGERANT AND AP-

PROVED POE COMPRESSOR OIL.

WARNING

LIVE ELECTRICAL COMPONENTS!

During installation, testing, servicing, and trouble-

shooting of this product, it may be necessary to work

with live electrical components. Failure to follow all

electrical safety precautions when exposed to live

electrical components could result in death or serious

injury.

WARNING

If using existing refrigerant lines make certain that all

joints are brazed, not soldered.

CAUTION

Scroll compressor dome temperatures may be hot. Do

not touch the top of compressor; it may cause minor to

severe burning.

CAUTION

WARNING

WARNING!

This product can expose you to chemicals including lead,

which are known to the State of California to cause cancer

and birth defects or other reproductive harm. For more

information go to www.P65Warnings.ca.gov

WARNING

18-AC51D1-10E-EN 3

Table 2.1

Section 2. Unit Location Considerations

2.1 Unit Dimensions and Weight

When mounting the outdoor unit on a roof, be sure the roof will support the unit’s weight.

Properly selected isolation is recommended to alleviate sound or vibration transmission to the building structure.

Unit Dimensions and Weight

Models H x D x W (in)

Weight* (lb)

4TTR4018N 29 x 26 x 29 133

4TTR4019N 29 x 30 x 33 161

4TTR4024N 29 x 26 x 29 133

4TTR4025N 29 x 30 x 33 162

4TTR4030N 33 x 30 x 33 156

4TTR4036N 33 x 30 x 33 156

4TTR4042N 37 x 34 x 37 212

4TTR4048N 29 x 34 x 37 189

4TTR4049N 45 x 34 x 37 256

4TTR4060N 45 x 34 x 37 277

4TTR4018L 29 x 26 x 29 133

4TTR4024/25L 29 x 26 x 29 133

4TTR4030/31L 29 x 30 x 33 156

4TTR4036/37L 33 x 30 x 33 156

4TTR4036/37M 29 x 30 x 33 161

4TTR4042/43L 29 x 34 x 37 184

4TTR4048L 29 x 34 x 37 189

4TTR4060L 37 x 34 x 37 211

* Weight values are estimated.

4 18-AC51D1-10E-EN

2.3 Suggested Locations for Best Reliability

Ensure the top discharge area is unrestricted for

at least five (5) feet above the unit.

Three (3) feet clearance must be provided in

front of the control box (access panels) and any

other side requiring service.

Do not locate close to bedrooms as operational

sounds may be objectionable.

Min. 12” to

Shrubber

Avoid Install

Near Bedrooms

Min 5’ Unrestricted

Access Panel

Min 3’

Unrestricted

2.2 Refrigerant Piping Limits

1. The maximum length of refrigerant lines

from outdoor to indoor unit should NOT

exceed sixty (60) feet.

2. The maximum vertical change should not

exceed sixty (60) feet.

3. Service valve connection diameters are

shown in Table 5.1.

Note: For line lengths greater than sixty (60)

feet, Refer to Refrigerant Piping Application

Guide, SS-APG006-EN or Refrigerant Piping

Software Program, 32-3312-03 (or latest revi-

sion).

60’

Max

Vertical

Change

Standard

Line Set

60’ Max

Line Length

60’

Max

Vertical

Change

18-AC51D1-10E-EN 5

Position the outdoor unit a minimum of 12” from

any wall or surrounding shrubbery to ensure

adequate airflow.

Outdoor unit location must be far enough away

from any structure to prevent excess roof runoff

water from pouring directly on the unit.

STEP 2 - To remove the unit from the pallet,

remove tabs by cutting with a sharp tool.

Section 3. Unit Preparation

3.1 Prepare The Unit For Installation

STEP 1 - Check for damage and report prompt-

ly to the carrier any damage found to the unit.

2.4 Coastal Considerations

If installed within one mile of salt water, including seacoasts and inland waterways, models without factory sup-

plied Seacoast Salt Shields require the addition of BAYSEAC001 (Seacoast Kit) at installation time.

Min. 12” to

Shrubbery

Min. 12”

to Wall

Section 4. Setting the Unit

4.1 Pad Installation

When installing the unit on a support pad, such

as a concrete slab, consider the following:

• The pad should be at least 1” larger than the

unit on all sides.

• The pad must be separate from any structure.

• The pad must be level.

• The pad should be high enough above grade

to allow for drainage.

• The pad location must comply with National,

State, and Local codes.

6 18-AC51D1-10E-EN

Section 5. Refrigerant Line Considerations

5.1 Refrigerant Line and Service Valve Connection Sizes

Table 5.1

5.3 Required Refrigerant Line Length

5.2 Factory Charge

Determine required line length and lift. You will

need this later in STEP 2 of Section 14.

Total Line Length = __________ Ft.

Total Vertical Change (lift) = __________ Ft.

The outdoor condensing units are factory

charged with the system charge required for the

outdoor condensing unit, ten (10) feet of tested

connecting line, and the smallest rated indoor

evaporative coil match. Always verify proper

system charge via subcooling (TXV/EEV) or

superheat (fixed orifice) per the unit nameplate.

See table for line length adders.

Line Length

TUBING INFORMATION

LINE TYPE REFRIGERANT TO ADD AT SPECIFIED

ADDITIONAL LENGTH

Suction

Line

Liquid

Line 20 ft 30 ft 40 ft 50 ft 60 ft

3/4" 3/8" 3 oz 9 oz 15 oz 21 oz 27 oz

7/8" 3/8" 3 oz 9 oz 16 oz 22 oz 28 oz

1-1/8" 3/8" 3 oz 9 oz 17 oz 23 oz 29 oz

Line Sizes Service Valve Connection Sizes

Model Vapor

Line

Liquid

Line

Vapor Line

Connection

Liquid Line

Connection

4TTR4018N 3/4 3/8 3/4 3/8

4TTR4019N 3/4 3/8 3/4 3/8

4TTR4024N 3/4 3/8 3/4 3/8

4TTR4025N 3/4 3/8 3/4 3/8

4TTR4030N 3/4 3/8 3/4 3/8

4TTR4036N 3/4 3/8 3/4 3/8

4TTR4042N 7/8 3/8 3/4 3/8

4TTR4048N 7/8 3/8 7/8 3/8

4TTR4049N 7/8 3/8 7/8 3/8

4TTR4060N 1-1/8 3/8 7/8 3/8

4TTR4018L 3/4 3/8 3/4 3/8

4TTR4024/25L 3/4 3/8 3/4 3/8

4TTR4030/31L 3/4 3/8 3/4 3/8

4TTR4036/37L 3/4 3/8 3/4 3/8

4TTR4036/37M 3/4 3/8 3/4 3/8

4TTR4042/43L 7/8 3/8 7/8 3/8

4TTR4048L 7/8 3/8 7/8 3/8

4TTR4060L 7/8 3/8 7/8 3/8

18-AC51D1-10E-EN 7

5.5 Reuse Existing Refrigerant Lines

CAUTION

If using existing refrigerant lines make certain that

all joints are brazed, not soldered.

Section 6. Refrigerant Line Routing

6.1 Precautions

Important: Take precautions to prevent noise

within the building structure due to vibration

transmission from the refrigerant lines.

For Example:

• When the refrigerant lines have to be fastened to floor joists or other framing in a structure, use isolation type

hangers.

• Isolation hangers should also be used when refrigerant lines are run in stud spaces or enclosed ceilings.

• Where the refrigerant lines run through a wall or sill, they should be insulated and isolated.

• Isolate the lines from all ductwork. • Minimize the number of 90º turns.

Comply with National, State, and Local Codes when

isolating line sets from joists, rafters, walls, or other

structural elements.

Isolation From Joist/Rafter

Side View

8 Feet Maximum

Secure Vapor line from joists using isolators every 8 ft. Secure

Liquid Line directly to Vapor line using tape, wire, or other appro-

priate method every 8 ft.

Joist/Rafter

Isolator

Line Set

8 Feet Maximum

5.4 Refrigerant Line Insulation

Important: The Vapor Line must always be

insulated. DO NOT allow the Liquid Line and

Vapor Line to come in direct (metal to metal)

contact.

Vapor Line

Liquid Line

Insulation

For retrofit applications, where the existing

indoor evaporator coil and/or refrigerant lines

will be used, the following precautions should

be taken:

• Ensure that the indoor evaporator coil and

refrigerant lines are the correct size.

• Ensure that the refrigerant lines are free of

leaks, acid, and oil.

Important: For more information see publica-

tion number SS-APG006-EN.

8 18-AC51D1-10E-EN

Isolation In Wall Spaces

Side View

Wall

Isolator

Line Set

8 Feet Maximum

Secure Vapor Line using isolators every 8 ft. Secure Liquid Line

directly to Vapor Line using tape, wire, or other appropriate

method every 8 ft.

8 Feet Maximum

Isolation Through Wall DO NOT hang line sets from ductwork

Sealant

Insulation

Vapor Line

Wall

Ductwork

Isolator

Line Set

Section 7. Refrigerant Line Brazing

7.1 Braze The Refrigerant Lines

STEP 1 - Remove caps or plugs. Use a debur-

ing tool to debur the pipe ends. Clean both

internal and external surfaces of the tubing

using an emery cloth.

18-AC51D1-10E-EN 9

STEP 2 - Remove the pressure tap cap and

valve cores from both service valves.

STEP 3 - Purge the refrigerant lines and indoor

coil with dry nitrogen.

STEP 4 - Wrap a wet rag around the valve body

to avoid heat damage and continue the dry nitro-

gen purge.

Braze the refrigerant lines to the service valves.

For units shipped with a field-installed external

drier, check liquid line filter drier’s directional flow

arrow to confirm correct direction of refrigeration

flow (away from outdoor unit and toward evapo-

rator coil) as illustrated. Braze the filter drier to

the Liquid Line.

Continue the dry nitrogen purge. Do not remove

the wet rag until all brazing is completed.

Important: Remove the wet rag before stopping

the dry nitrogen purge.

Note: Install drier in Liquid Line.

NOTE:NOTE: Precautions should be taken to avoidPrecautions should be taken to avoid

heat damage to basepan during brazing. It isheat damage to basepan during brazing. It is

recommended to keep the flame directly off ofrecommended to keep the flame directly off of

the basepan.the basepan.

3-4” from valve

10 18-AC51D1-10E-EN

STEP 5 - Replace the pressure tap valve cores

after the service valves have cooled.

STEP 2 - Check for leaks by using a soapy solu-

tion or bubbles at each brazed location.

Remove nitrogren pressure and repair any leaks

before continuing.

Section 8. Refrigerant Line Leak Check

8.1 Check For Leaks

STEP 1 - Pressurize the refrigerant lines and

evaporator coil to 150 PSIG using dry nitrogen.

150 PSIG

Inhaltsverzeichnis

Andere Trane Klimaanlage Handbücher

Trane

Trane XL Montageanleitung

Trane

Trane UniTrane FCD Betriebsanleitung

Trane

Trane FIAECON102 Series Bedienungsanleitung

Trane

Trane 18, 24, 30, 36, 24, 42, 48 Bedienungsanleitung

Trane

Trane 4TTA3030A4000C Service-Handbuch

Trane

Trane OXBOX J4AC4 Series Bedienungsanleitung

Trane

Trane TWA0724-A Series Montage- und Bedienungsanleitung

Trane

Trane IntelliPak 2 Series Montage- und Bedienungsanleitung

Trane

Trane CONTURA 3G CASSETTE Bedienungsanleitung

Trane

Trane Voyager YS 150F Bedienungsanleitung

Trane

Trane 4TTR3 Montageanleitung

Trane

Trane MCXE Series Reparaturanleitung

Trane

Trane MITSUBISHI ELECTRIC TPEFYP015MH142A Bedienungsanleitung

Trane

Trane GRAA Bedienungsanleitung

Trane

Trane Foundation GBC180 Montage- und Bedienungsanleitung

Trane

Trane 2TEE3D31A1000A Leitfaden

Trane

Trane Mitsubishi Electric NTXMMX20A122A Series Bedienungsanleitung

Trane

Trane MXW Betriebsanleitung

Trane

Trane Foundation BAYENTH321 Series Bedienungsanleitung

Trane

Trane 4MXC8512B10N0 Benutzerhandbuch

Trane

Trane RAUJ-C20 Montage- und Bedienungsanleitung

Trane

Trane VariTrane VAV Series Administratorhandbuch

Trane

Trane 4TXCA002DS3HCB Montageanleitung

Trane

Trane 4TWL6036A1000A Service-Handbuch

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung