Trane CLCH Betriebsanleitung

Installation

Operation

Maintenance

CLCH

QuantumClimate Changer

Air Handling Units

CLCH-SVX05A-GB

General

Information

©American Standard Inc. 2002

Foreword

These installation, operation, and

maintenance instructions are given as a

guide to good practice in the installation,

commissioning into service, operation,

and periodic maintenance by the user, of

CLCH Air Handling Units. They do not

contain the full service procedures

necessary for the continued successful

operation of this equipment. The services

of a qualified service technician should be

employed through the medium of a

maintenance contract with a reputable

service company.

Warranty

Trane’s standard warranty covers the

equipment. It does not cover damage due

to misuse, lack of maintenance, or failure

to comply with the manufacturer's

instructions or recommendations.

Receiving/Handling

On arrival, inspect the unit before signing

the delivery note. Specify any damage on

the delivery note, and send a registered

letter of protest to the last carrier of the

goods within 72 hours of delivery. Notify

the local Trane sales office at the same

time. The unit should be totally inspected

within 15 days of delivery. If any

concealed damage is discovered, stop

unpacking the shipment. Take photos of

the damaged material if possible. Notify

the carrier immediately by phone and

registered mail. Notify the local Trane

sales office. Concealed damage must be

reported within 15 days of delivery.

About This Manual

Warnings appear at appropriate places in

this instruction manual. Your personal

safety and the correct operation of this

machine require that you follow the

warnings carefully. The manufacturer

assumes no liability for installations or

servicing undertaken by unqualified

personnel.

About The Unit

The information contained in this manual

applies to units designated CLCH

Contents

1. Introduction

2. Delivery Check On Arrival/Off-Loading

and Movement To The Site

3. Foundations and Erection

4. Assembly and Installation

5. Commissioning Procedure

6. Maintenance

7. Troubleshooting

CLCH-SVX05A-GB

1. Introduction

Please pay particular attention to the

instructions on the unit in accordance with

the identification label, assembly

drawings, and special warnings or advice

labels.

CLCH-SVX05A-GB 5

2. Delivery Check On

Arrival/Off-Loading and

Movement To The Site

2.1 Delivery Check

Check the delivery contents on arrival of

CLCH units in respect of completeness,

and note any damage which may have

occurred. In the event of any damage

being noted, a claim must be made by

return. Only by compliance with this

procedure is it possible to submit an

insurance claim. Any damage must be

noted on the delivery documentation,

dated and signed in the presence of the

delivery driver, and signalled by

registered letter to the last forwarder.

Claims in respect of obvious transport

damage or incompleteness of delivery

cannot be accepted in retrospect. In

the event of any complaints, please

notify the relevant Trane office

immediately, and in writing within 72

hours.

2.1.1. Identification

All Trane CLCH units are identified by the

sales number and manufacturer's works

order number given on the unit ID label.

Be sure to refer to the information given

on the unit identification label when

ordering replacement parts or requesting

service. The nameplate (see Figure 1) is

mounted on the fan-section access side,

and a manufacturer's plate (see Figure 2)

is fixed inside the fan section.

Figure 2 – Manufacturers Plate

2.2 Off Loading

A specific lifting method for offloading the

units is recommended as follows (see

Figure 3):

1) 52 mm-diameter lifting holes, or

certified lifting lugs, are provided on the

unit base frame.

2) ALL LIFTING POINTS in one axis of

the unit must be used when offloading

and moving the unit.

3) Slings and spreader bars are to be

provided by the rigger and attached to

ALL LIFTING POINTS.

4) The minimum rated lifting capacity

(vertical) of each sling and spreader

bar should be no less than the shipping

weight.

5) The unit must be lifted with care,

avoiding shock load by lifting the unit

slowly and evenly.

2.3 Moving To Position On

Site

Trane units are supplied in sections

modules, flat packed, or as a complete

unit, in accordance with the relevant

assembly drawings. Any necessary use

of force during unloading or movement of

the units must only be applied via the unit

base frame or shipping pallet.

NEVER LIFT THE UNITS BY COIL

CONNECTIONS OR BY ANY OTHER

PROTRUSIONS.

THE ROOF IS NOT DESIGNED TO BE

WALKED ON, BUT IF THIS IS

UNAVOIDABLE, ENSURE A MORE

EVEN WEIGHT DISTRIBUTION BY

THE USE OF BOARDS.

FAILURE TO DO SO MAY RESULT IN

SEVERE PERSONAL INJURY OR

DEATH.

WARNING

Figure 3

Figure 1 – Nameplate

ENSURE SLINGS DO NOT FOUL ON

UNIT PROTRUSIONS.

THE CENTRE OF GRAVITY WILL

VARY PER UNIT…POSITION THE

SLINGS AND SPREADER BARS

CAREFULLY TO COMPENSATE FOR

THIS.

FAILURE TO DO SO MAY RESULT IN

SEVERE PERSONAL INJURY OR

DEATH.

WARNING

2. Delivery Check On

Arrival/Off-Loading and

Movement To The Site

2.4 Forklift Trucks

The forks must only be applied under the

unit base frame and not against the unit

base frame. The lift point should be as

near as possible to the centre of gravity

(see Figures 4 and 4a). In the case of

larger units the use of several forklift

trucks may be required.

2.4.1. Roller Movement

Units fitted with base frames may be

moved on roller trolleys or tubular rollers

(see Figure 5).

Figure 4

Figure 4A

Figure 5

CLCH-SVX05A-GB

3. Foundations and

Erection

3.1 Foundation

When selecting and preparing the unit

site, follow these guidelines:

1. Ensure that the site can support the

total weight of the unit. Unit weight

figures only provide total gross weights

and do not include the additional

weight for water in any coils.

2. Confirm that the foundation of the

mounting platform is large enough to

include the unit dimensions plus

service plus service access.

3. The floor or foundation must be level

for correct coil drainage and

condensate flow.

4. Provide adequate lighting for

maintenance personnel to perform

maintenance duties.

5. When the unit is positioned on site,

there must be sufficient space around

the unit to ensure that correct operation

and effective maintenance can be

carried out. Figure 6 gives

recommended space allowances.

•On the designated access side of the

unit, working areas must be equal to the

width of the unit, dimension “P.”

•Allowance for coil connections,

dimension “C” must be dimension “P” +

200 mm.

•A clear unobstructed area before and

after an air intake or discharge is

required to ensure correct air

movement. The width of the area must

be >= the width of the unit, and the

depth (dimension "L") must be >= 0.5 x

the overall unit height.

Complete reinforced concrete

foundations are suitable or strip

foundations may also be used (see

Figure 7).

In the case of strip foundations, concrete

or steel supports are permissible, but

support is required under breakpoints and

every 2 m along the unit base.

Figure 7 – Air Handling Unit Steels Foundation

Figure 6

CLCH-SVX05A-GB

3. Foundations and

Erection

Figure 8 – Air Handling Unit Plinth Foundation

FAILURE TO PROVIDE A LEVEL

PLINTH OR SUPPORT WILL RESULT

IN DOORS JAMMING AND AIR LEAKS

FROM THE CASING.

3.2 Erection

To minimize noise transmission,

insulation material such as cork slabbing

(TICO pads) may be placed between the

unit base and the foundation (see Figure

8).

IMPORTANT

CLCH-SVX05A-GB

4. Assembly and

Installation

4.1 Break Point and General

Unit Assembly

Instructions

Ensure that all the air-handling unit

sections are positioned in the correct

order.

Each section will display a unit drawing

with its position OUTLINED.

1. Each of the unit sections should be

placed on a level foundation and within

200 mm of its adjoining section.

2. Remove any supports and bracing

which are supplied with the unit for

transport. All such supports will be

clearly marked:

“FOR TRANSPORT ONLY –

REMOVE BEFORE ASSEMBLY”

3. Remove 4 M6 fixing bolts (A) from the

protruding portion of the 4 framework

joining bars (see Figure 9), then loosen

the remaining 4 bolts that are located

on the fixed side of the break point

joining bars.

Pull together the sections of the unit,

ensuring that the joiner bar in each of

the 4 corners is fitted into its adjoining

section and the plastic “T” section

sealing strip locates over the adjoining

panel.

The 52-mm diameter holes provided in

the unit base frame should be used to

manoeuvre the sections together.

Greased skid plates will greatly assist

the whole assembly operation.

4. Secure the break point joint externally

by replacing the 4 M6 bolts and

washers, which were previously

removed in step (3). Retighten the 8

bolts located on both sides of the break

point joint.

Where applicable, complete the

assembly of the unit as follows:

4.1.3. Fan sections

Bolt the outlet of the fan to the flexible

connection using the M8 bolts provided.

4.1.4. Damper sections

Pop-rivet through the damper spigot and

the adjoining plastic “J” section into the

adjacent fixed panel using 5-mm-

diameter rivets.

4.1.5. Coil sections (with drip pans)

Fix through the top of the drip pan into the

box section using the self-drilling screws,

which are provided. Then seal along all

joints with a waterproof “silicone” based

sealant. We recommend “Siloflex.”

4.1.6. Weatherproof roofs

Slide on the “Doby” cleats, which are

provided, and then fix in position at the

ends with the cleat clips on the roof return

edge using 5mm diameter rivets.

CLCH-SVX05A-GB

Figure 9

Figure Notes:

1. Part 1

2.Part 2

3. Break Point

4. Bolts “A”

5. Fixed bolts

6. 52 mm diameter holes

7. 8 x M6 bolts (2 per join)

4. Assembly and

Installation

4.2 Stacked Units (Top and

Bottom)

Lower the top unit into position on top of

the bottom unit, taking care not to

damage the sealing gaskets.

Fit the self-tapping screws to the fixing

brackets, which are already positioned on

the top edge of the bottom unit,drilling into

the top unit section (10A) or base frame

(10B) depending on product, in order to

secure the top unit to the bottom unit (see

Figure 10).

Fix into position any internal joining strips

and/or brackets that are provided, and

then seal up any common sections in the

top and bottom units.

4.2.1. Stacked units (Side by Side)

Manoeuvre the two units into their correct

positions, taking care not to damage any

sealing gaskets.

Fix through the fixing brackets which are

located at both ends of the units in order

to secure the units together. Also fix into

position any base frame, unit end, and

roof joining brackets that are provided.

Fix into position any internal joining strips

and/or brackets that are provided, and

then seal up any common sections in

both of the units.

If you require further assistance or have

any questions please contact your local

Trane sales office.

4.3 Assembly of Flatpacked

Units

The unit is fully assembled in the factory

on a flat and level surface. Prior to

disassembly for flat packing (see Figure

11) all items are marked

alphanumerically. All items marked “A”

are joined at the fixing indicated at this

point. These markings are on labels on

internal surfaces so they are not evident

upon completion. DO NOT remove labels

until assembly is complete.

We would recommend opening one unit

at a time to avoid confusion.

Figure 10 A/B

Figure Notes:

1. Self tapping screws

2. Bottomframework of TOP unit

3. Fixing bracket

4. Top framework of BOTTOM unit

Figure 11

CLCH-SVX05A-GB

Figure 10A Figure 10B

Inhaltsverzeichnis

Andere Trane Klimaanlage Handbücher

Trane

Trane 4TYK8536B1000AA Betriebsanleitung

Trane

Trane BAYECON085A Montageanleitung

Trane

Trane Tracker Version 12 Handbuch

Trane

Trane Precedent DSJ150A Montage- und Bedienungsanleitung

Trane

Trane 4DCY4024 Montageanleitung

Trane

Trane 4TXM2318BF300AA Bedienungsanleitung

Trane

Trane MCW509AMUA0 Bedienungsanleitung

Trane

Trane IntelliPak SAHL Series Montage- und Bedienungsanleitung

Trane

Trane 38 Series Benutzerhandbuch

Trane

Trane 4YCZ6036A Montageanleitung

Trane

Trane Odyssey Series Bedienungsanleitung

Trane

Trane 4TWL6018A1000A Montageanleitung

Trane

Trane 4TWL6036A1000A Service-Handbuch

Trane

Trane ODYSSEY TTA Series Betriebsanleitung

Trane

Trane Voyager 27 to 50 Ton Montage- und Bedienungsanleitung

Trane

Trane MWC518 Bedienungsanleitung

Trane

Trane 4MXX8509B10N0 Benutzerhandbuch

Trane

Trane NEW STYLUS MCX Series Bedienungsanleitung

Trane

Trane Precedent YZJ150A Montage- und Bedienungsanleitung

Trane

Trane Foundation GBC Series Montage- und Bedienungsanleitung

Trane

Trane Voyager TS 150G Series Montage- und Bedienungsanleitung

Trane

Trane RAU-SVX01B-E4 Betriebsanleitung

Trane

Trane Foundation BAYENTH321 Series Bedienungsanleitung

Trane

Trane FADA Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung