Trane IntelliPak Betriebsanleitung

SAFETY WARNING

Only qualified personnel should install and service the equipment. The installation, starting up, and servicing

of heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and

training. Improperly installed, adjusted or altered equipment by an unqualified person could result in death or

serious injury. When working on the equipment, observe all precautions in the literature and on the tags,

stickers, and labels that are attached to the equipment.

Programming Guide

RT-SVP011A-EN

December 2018

IntelliPak™ with Symbio™ 800, 20 to 75 Ton

with the Tracer®TD7 Display

Introduction

Warnings, Cautions, and Notices

Safety advisories appear throughout this manual as required. Your personal safety and the proper

operation of this machine depend upon the strict observance of these precautions.

The three types of advisories are defined as follows:

WARNING Indicates a potentially hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTIONsIndicates a potentially hazardous situation which, if not avoided, could result in

minor or moderate injury. It could also be used to alert against unsafe practices.

NOTICE Indicates a situation that could result in equipment or property-damage only

accidents.

WARNING

Proper Field Wiring and Grounding Required!

Failure to follow code could result in death or serious injury. All field wiring MUST be

performed by qualified personnel. Improperly installed and grounded field wiring poses FIRE

and ELECTROCUTION hazards. To avoid these hazards, you MUST follow requirements for field

wiring installation and grounding as described in NEC and your local/state electrical codes.

Failure to follow code could result in death or serious injury.

WARNING

Personal Protective Equipment (PPE) Required!

Failure to wear proper PPE for the job being undertaken could result in death or serious injury.

Technicians, in order to protect themselves from potential electrical, mechanical, and chemical

hazards, MUST follow precautions in this manual and on the tags, stickers, and labels, as well

as the instructions below:

• Before installing/servicing this unit, technicians MUST put on all PPE required for the work

being undertaken (Examples; cut resistant gloves/sleeves, butyl gloves, safety glasses, hard

hat/bump cap, fall protection, electrical PPE and arc flash clothing). ALWAYS refer to

appropriate Material Safety Data Sheets (MSDS)/Safety Data Sheets (SDS) and OSHA

guidelines for proper PPE.

• When working with or around hazardous chemicals, ALWAYS refer to the appropriate MSDS/

SDS and OSHA/GHS (Global Harmonized System of Classification and Labelling of

Chemicals) guidelines for information on allowable personal exposure levels, proper

respiratory protection and handling instructions.

• If there is a risk of energized electrical contact, arc, or flash, technicians MUST put on all PPE

in accordance with OSHA, NFPA 70E, or other country-specific requirements for arc flash

protection, PRIOR to servicing the unit. NEVER PERFORM ANY SWITCHING,

DISCONNECTING, OR VOLTAGE TESTING WITHOUT PROPER ELECTRICAL PPE AND ARC

FLASH CLOTHING. ENSURE ELECTRICAL METERS AND EQUIPMENT ARE PROPERLY RATED

FOR INTENDED VOLTAGE.

RT-SVP011A-EN 3

Introduction

This document and the information in it are the property of Trane, and may not be used or

reproduced in whole or in part without written permission. Trane reserves the right to revise this

publication at any time, and to make changes to its content without obligation to notify any person

of such revision or change.

Trademarks

All trademarks referenced in this document are the trademarks of their respective owners.

Agency Listings and Compliance

The European Union (EU) Declaration of Conformity is available from your local Trane® office.

Revision History

New

4 RT-SVP011A-EN

Table of Contents

Introduction ......................................................6

Hardware ...................................................... 6

Communication ............................................... 6

Screen Characteristics .......................................... 6

Touchscreen Guidelines .......................................... 6

Dimensions .................................................... 7

Specifications and Agency Compliance ............................. 8

Controller and Service Tool Requirements ........................... 8

Tracer TU .................................................... 8

WebUI ...................................................... 8

Supported Languages ............................................ 9

Screen Overview ............................................... 10

Top Display Area ............................................. 10

Main Display Area (Home Screen) ............................... 11

Bottom Display Area .......................................... 11

Alarms ..........................................................13

Active Alarms ................................................. 13

Viewing Active Alarms ........................................ 14

Alarm Icons ................................................... 14

Sorting Alarms ................................................ 15

Configuring Alarms ............................................. 15

Reports .........................................................17

Custom Reports ................................................ 17

Creating a Custom Report ..................................... 17

Editing a Custom Report ....................................... 19

All Points Report ............................................... 20

Points Overrides ............................................... 21

Binary Overrides ............................................. 22

Multistate Overrides .......................................... 23

Analog Overrides ............................................. 23

Setting Up a Temporary Override ............................... 24

............................................................. 24

Override Summary ............................................. 24

About ........................................................ 25

Expansion Modules ............................................. 27

TGP2 Programs ................................................ 29

Data Logs ..................................................... 29

Using the Trend Viewer ......................................... 30

Data Graphs .....................................................31

RT-SVP011A-EN 5

Table of Contents

Creating a Data Graph .......................................... 31

Settings .........................................................36

Control Settings ................................................ 36

Equipment Settings ............................................. 37

Unit Settings ................................................ 37

Feature Settings .............................................. 37

Manual Overrides ............................................ 37

Display Settings ................................................ 38

Display Preferences ........................................... 38

Language ................................................... 41

Date and Time ............................................... 42

Clean Touchscreen ........................................... 43

Schedules ..................................................... 43

Optimal Start/Stop ............................................ 44

Exceptions and Calendars ..................................... 44

Creating a Schedule .......................................... 44

The Tools Menu ................................................ 45

Backup and Restore ........................................... 45

Programs ................................................... 46

System Logs ................................................ 46

Recent Usage ................................................ 46

BACnet Information ........................................... 46

Configuring Basic Settings for the Symbio 800 ...................... 46

Regional Specifications ........................................ 47

Symbio 800 System Units ..................................... 47

Identification and Communication ............................... 47

USB Ports and microSD ....................................... 48

Licensing ................................................... 48

Configuring Additional Settings .................................. 49

Defaults for User Preferences ................................... 49

Application Defaults .......................................... 49

SMTP Settings ............................................... 50

Priority Levels ............................................... 50

Troubleshooting ..................................................52

Identifying and Diagnosing Issues ................................. 52

........................................................... 83

TD7 Automatic Rediscover and Automatic Hardware Reboot ........ 83

Notes ...........................................................85

6 RT-SVP011A-EN

Introduction

The purpose of this guide is to assist you in installing, programming, and operating with the

TracerTD7 Display and the Web UI, which interacts with the unit controls. This guide describes how

to access the screens and the types of information that appear on the screens.

The Tracer TD7 display is mounted to the unit and allows you to view data and make operational

changes to the equipment.

The Web UI is a built in service tool that allows users to set up, operate, and troubleshoot the

equipment.

Hardware

The Tracer TD7 is a durable factory-mounted touch screen display that is designed to operate in

both indoor or outdoor environments. The TD7 display utilizes a standard 75mm VESA mounting

pattern for installation in a Trane Large enclosure. Alternatively, it can be installed with a user-

supplied VESA mount.

Communication

A separate Ethernet cable provides communication between the Tracer TD7 display and the unit

controller.

Screen Characteristics

The 7-inch WVGA 800 x 480 resolution touch-sensitive color screen is backlit, which enables

viewing in poor light conditions including outdoor usage (with the exception of direct sunlight).

Touchscreen Guidelines

The touch screen registers the downward pressure of a touch. Light, quick, yet deliberate touches

are most effective. Touching with more pressure has no effect.

Recommended tools to use:

• finger

• thumb

• pencil eraser

Do not use:

• a screwdriver

• a pen

• a pencil point

• any other sharp or pointed object that might scratch the screen surface

RT-SVP011A-EN 7

Introduction

Dimensions

7.9 in. (200.7 mm)

1.7 in. (41.9 mm) 8.3 in. (211.6 mm)

6.3 in. (158.8 mm)

2.1 in. (53.2 mm)

5.5 in. (139.9 mm)

Note: The power cable is permanently attached to the

TD7 display. The power connector provides

strain relief and protection from the elements.

8 RT-SVP011A-EN

Introduction

Specifications and Agency Compliance

Controller and Service Tool Requirements

Tracer TU

Tracer TU Service Tool Version 10.2 or higher is only required for TGP2 and modifications done in

the field.

Note: Tracer TU is not needed for normal operation. If you need to perform configuration changes,

add new features, or customize the operation of the equipment, contact your local Trane

office.

Web UI

To perform firmware updates, setup communication protocols, backup and restore, scheduling,

and create users or custom trend views connect using Web UI:

1. Connect a laptop to the USB service tool port using a USB 2.0 A to Be cable.

2. Open a web browser and connect to http://198.80.81.1 to access Web UI.

Figure 1. Web UI connection

Specification

Input power: 24 Vac +/- 15%, 21 VA, 50 or 60 Hz

Storage temperature: -67°F to 203°F (-55°C to 95°C)

Humidity: Between 5% and 100% (non-condensing)

Operating temperature: Temperature: -40°F to 158°F (-40°C to 70°C)

Humidity: Between 5% and 100% (non-condensing)

Mounting weight: Mounting surface must support 1.625 lb (0.737 kg)

Mounting Type: VESA (75 mm x 75 mm)

Environmental rating (enclosure): IP56 (dust and strong water protected) with use of an optional Sealed Ethernet Cable

Agency Compliance

• UL916 PAZX, Open Energy Management Equipment

• UL94-5V, Flammability

• FCC CFR Title 47, Part 15.109: Class A Limit, (30 MHz—4 GHz)

• CE EMC Directive 2004/108/EC

RT-SVP011A-EN 9

Introduction

Supported Browsers for Tracer Symbio Web UI

Microsoft Windows 7:

• Internet Explorer 11 (limited support)

• Mozilla Firefox (most recent version)

• Google Chrome (most recent version)

Microsoft Windows 8.1: (no support)

Microsoft Windows 10:

• Internet Explorer 11 (no support)

• Microsoft Edge (most recent version)

• Mozilla Firefox (most recent version)

• Google Chrome (most recent version)

Apple Mac OS (latest version -1)

• Mozilla Firefox (most recent version)

• Google Chrome (most recent version)

• Safari (most recent version)

Creating a New User in Web UI

Note: For more detailed instructions on creating a new user, click the help icon in the global

navigation bar within Web UI.

To create a new user:

1. From the global navigation bar, select Admin > Users.

2. Click the Create User button.

3. Enter the user’s personal information, and click Next.

4. On the Preferences page, determine how certain attributes on the Symbio 800 user interface

will display. Click Next.

5. On the Data Display Units Preference page, determine the unit type in which data will be

displayed. Click Next.

6. On the Data Display Units Preference page, determine the preferred display units. Click Next.

7. On the summary page, review your selections. Click Finish to save the new user.

Supported Languages

The TD7 display supports built-in languages:

• English

• French (Canadian)

• Spanish (Latin American)

10 RT-SVP011A-EN

Introduction

Screen Overview

There are three distinct areas on the TD7 screens:

• Top display area

• Main display area

• Bottom display area

Top Display Area

Figure 2. Tracer TD7 display screen

Main display area

Top display area

Bottom display area

The Back button, when touched, returns to the previous screen visited.

TheHomebutton,whentouched,navigatestotheAllPointsReportbydefault.HomeCan

be configured to display any of the three custom reports, All Points Report, All Points in

Override Report, Alarms, or custom graphic. See “Display Preferences,” p. 43.

TheOverridesSummarybuttonprovides anat-a-glanceview ofhowmany useroverrides

exist and provides a link to the Override Summary report.

The Space Temperature Active or Discharge Air Temperature Active, depending on

configuration is displayed in the header Data Area.

Andere Handbücher für IntelliPak

Inhaltsverzeichnis

Andere Trane Klimaanlage Handbücher

Trane

Trane HFCF-SVX01A-EN Betriebsanleitung

Trane

Trane Precedent WSJ150A Montage- und Bedienungsanleitung

Trane

Trane EB 036 Series Montage- und Bedienungsanleitung

Trane

Trane OXBOX JMM5A0A24M21SAA Montageanleitung

Trane

Trane A5AC5018A Bedienungsanleitung

Trane

Trane Mitsubishi Electric NTXMMX20A122A Series Bedienungsanleitung

Trane

Trane TXUM524 Betriebsanleitung

Trane

Trane ComfortLink II 4TWV0X24A1000A Montageanleitung

Trane

Trane MXZ-2C20NA3-U1 Bedienungsanleitung

Trane

Trane 4MCW3-A Bedienungsanleitung

Trane

Trane TC*150-301 Betriebsanleitung

Trane

Trane CyberRow DX Montage- und Bedienungsanleitung

Trane

Trane YSC060ED Montage- und Bedienungsanleitung

Trane

Trane Precedent YSC060-120 Bedienungsanleitung

Trane

Trane Voyager CV Produkthandbuch

Trane

Trane BAYECON355 Series Bedienungsanleitung

Trane

Trane MITSUBISHI ELECTRIC NTXSKS18A112A Series Bedienungsanleitung

Trane

Trane 4TVS0007DF000A Betriebsanleitung

Trane

Trane RAUC-C20 Betriebsanleitung

Trane

Trane IntelliPak 1 with Symbio 800 Montage- und Bedienungsanleitung

Trane

Trane Mitsubishi Electric TPEFYP006MA143A Bedienungsanleitung

Trane

Trane TVR Pro CO Series Bedienungsanleitung

Trane

Trane TCH024C1 Betriebsanleitung

Trane

Trane 4TCA4024A1000A Montageanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung