Trane PM014 Montage- und Bedienungsanleitung
SAFETY WARNING
Only qualified personnel should install and service the equipment. The installation, starting up, and servicing
of heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and
training. Improperly installed, adjusted or altered equipment by an unqualified person could result in death or
serious injury. When working on the equipment, observe all precautions in the literature and on the tags,
stickers, and labels that are attached to the equipment.
Power Supply Module PM014
24 Vdc forTrane®inter-module communication buses
PM014
Installation, Operation,
and Maintenance
BAS-SVX33F-EN
January 2018
© 2018 Ingersoll Rand All rights reserved BAS-SVX33F-EN
Introduction
Warnings, Cautions, and Notices
Safety advisories appear throughout this manual as required.Your personal safety and the proper
operation of this machine depend upon the strict observance of these precautions.
The three types of advisories are defined as follows:
WARNING Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTIONsIndicates a potentially hazardous situation which, if not avoided, could result in
minor or moderate injury. It could also be used to alert against unsafe practices.
NOTICE Indicates a situation that could result in equipment or property-damage only
accidents.
WARNING
Proper Field Wiring and Grounding Required!
Failure to follow code could result in death or serious injury. All field wiring MUST be
performed by qualified personnel. Improperly installed and grounded field wiring poses FIRE
and ELECTROCUTION hazards.To avoid these hazards, you MUST follow requirements for field
wiring installation and grounding as described in NEC and your local/state electrical codes.
Failure to follow code could result in death or serious injury.
WARNING
Personal Protective Equipment (PPE) Required!
Installing/servicing this unit could result in exposure to electrical, mechanical and chemical
hazards.
• Before installing/servicing this unit, technicians MUST put on all PPE required for the work
being undertaken (Examples; cut resistant gloves/sleeves, butyl gloves, safety glasses, hard
hat/bump cap, fall protection, electrical PPE and arc flash clothing). ALWAYS refer to
appropriate Material Safety Data Sheets (MSDS)/Safety Data Sheets (SDS) and OSHA
guidelines for proper PPE.
• When working with or around hazardous chemicals,ALWAYS refer to the appropriate MSDS/
SDS and OSHA/GHS (Global Harmonized System of Classification and Labeling of
Chemicals) guidelines for information on allowable personal exposure levels, proper
respiratory protection and handling instructions.
• If there is a risk of energized electrical contact, arc, or flash, technicians MUST put on all PPE
in accordance with OSHA, NFPA 70E, or other country-specific requirements for arc flash
protection, PRIOR to servicing the unit. NEVER PERFORM ANY SWITCHING,
DISCONNECTING, OR VOLTAGE TESTING WITHOUT PROPER ELECTRICAL PPE AND ARC
FLASH CLOTHING. ENSURE ELECTRICAL METERS AND EQUIPMENT ARE PROPERLY RATED
FOR INTENDED VOLTAGE.
Failure to follow instructions could result in death or serious injury.
BAS-SVX33F-EN 3
Introduction
Copyright
This document and the information in it are the property ofTrane, and may not be used or
reproduced in whole or in part without written permission.Trane reserves the right to revise this
publication at any time, and to make changes to its content without obligation to notify any person
of such revision or change.
Trademarks
All trademarks referenced in this document are the trademarks of their respective owners.
Agency Listings and Compliance
The European Union (EU) Declaration of Conformity is available from your localTrane® office.
Revision History
BAS-SVX33F-EN
• Changed terminology to reflect new SC+ system controller.
4 BAS-SVX33F-EN
Table of Contents
General Information ...............................................5
Dimensions .................................................... 6
Clearances ..................................................... 6
Codes and Standards Compliance .................................. 7
Specifications .................................................. 8
Pre-Installation ....................................................9
Mounting Location .............................................. 9
Transformer Considerations ...................................... 9
Recommended Configuration .................................... 10
Installing the Power Supply Module .................................11
Repositioning or Removing the Power Supply Module ............... 12
Power and Field Wiring ......................................... 13
Installing Power Input Wire .................................... 13
Grounding the Power Supply Module ............................ 14
Installing Field Wire ........................................... 14
Separating the IMC Bus for Large Systems ....................... 15
Starting Up the Power Supply Module ........................... 16
Operation and Troubleshooting .....................................17
Operational Features ............................................ 17
Troubleshooting ............................................... 17
BAS-SVX33F-EN 5
General Information
This section provides the following product information for the power supply module:
• Product description
• Dimensions
• Clearances
• Codes and standards compliance
• Specifications
The PM014 power supply module provides 24 Vdc forTraneinter-module communication (IMC)
buses. IMC buses are used in components ofTrane building automation systems (BAS), such as
theTracer® SC+ system controller and theTracer XM30 expansion module, and other equipment.
The PM014 uses a full-wave rectifier. It is designed to safely share power with a device that uses
half-wave rectification within the transformer limits.The power supply module has four
connections that provide power to an IMC bus:
• Two four-pin IMC pin connections for use with wiring harnesses.
• Two four-pin IMC terminal blocks for use with field wiring.
Figure 1. Power supply module components
PM014
24
VAC
XFMR
OUT
24
VAC
24 Vac input connection
24 Vac output connection
Status LED
IMC pin connection
IMC pin connection
IMC terminal block
IMC terminal block
Example of a wiring
harness (for use with IMC
pin connections)
6 BAS-SVX33F-EN
General Information
Dimensions
The following illustration provides specific dimension details.
Clearances
Clearances must be provided for air circulation, mounting the power supply module, and
connecting cables.The following illustration and table provide the recommended minimum
clearances.
24
24
VAC
VAC
XFMR
XFMR
OUT
OUT
24
24
VAC
VAC
2.4 in.
(6.14 cm)
2.4 in.
(6.1 cm)
1.8 in.
(4.5 cm)
4.0 in.
(10.2 cm)
2.4 in.
(6.1 cm)
1.2 in.
(3.1 cm)
0.6 in.
(1.5 cm)
2.0 in.
(5.0 cm)
2.0 in.
(5.0 cm)
PM014
24
VAC
XFMR
OUT
24
VAC
Vents
Vent clearance
Vent clearance
Vents Clearance Measurement
Installing and operating In accordance with local
electrical codes
Vent space 1.8 in. minimum (4.6 cm)
Note: The power supply vents must have adequate open space to
allow convective air flow to cool the unit.
1.8 in.
(4.6 cm)
1.8 in.
(4.6 cm)
BAS-SVX33F-EN 7
General Information
Codes and Standards Compliance
The power supply module is in conformance with the codes and standards listed in Table 1.
Table 1. Codes and standards
Listing Description
UL/C-UL/IEC60950-1 UL recognized under Information Technology Equipment – Safety –
Part 1: General Requirements
UL916 Open listing
CE Conformity The European Union (EU) Declaration of Conformity is available from
your local Trane® office.
FCC Part 15, Class A Emissions —
2002/95/EC – RoHS Restriction of hazardous substances directive
8 BAS-SVX33F-EN
General Information
Specifications
The power supply module is in conformance with the physical, environmental, and electrical
specifications as listed in the following tables.
(a)The power supply output is UL 1310 class 2 and IEC60950-1 limited power source (LPS).
(b) Maximum required for 1.4 A DC loading.
Table 2. PM014 Specifications
Enclosure IP20 (NEMA 1)
DIN rail DIN 50022, 35 mm x 7.5 mm
Environmental Parameters:
• Storage temperature -67°F (-55°C) minimum; 203°F (95°C) maximum
• Operating temperature –40°F (–40°C) minimum; 158°F (70°C) maximum
• Humidity (non-condensing) 5% relative humidity (RH) minimum; 95% RH maximum
Electrical Parameters:
• Output voltage(a) 22.8 Vdc minimum; 24 Vdc nominal; 25.2 Vdc maximum
• Output current(a) 0 minimum; 1.4 Adc maximum
• Input voltage 18 Vac minimum; 24 Vac nominal; 32 Vac maximum; 50 or 60 Hz
• Input VA 20 VA minimum; 76 VA(b)
BAS-SVX33F-EN 9
Pre-Installation
This section provides the following pre-installation information:
• Mounting location
• Transformer considerations
• Recommended configurations
Mounting Location
Important: The power supply module must be mounted onto a DIN rail inside an enclosure that
meets all local electrical codes.
Observe the following:
• The enclosure must allow for the minimum 1.8 in. (4.6 cm) vent clearance around the top and
bottom of the power supply vents.
• The mounting location must meet the temperature and humidity specifications of the power
supply as outlined in Table 3, p. 9.
• Do not mount the power supply module on a flat surface, such as on a floor or on top of a table.
Mount in an upright position with the front facing outward.
Transformer Considerations
Follow these guidelines when using transformers:
• Transformers must be class 2 rated.
• Non-class 2 transformers must be fused appropriately.
• Fully loaded power supply modules require 75 VA transformers.
The transformer size can be reduced for smaller loads on the power supply module; however,
transformers less than 20VA should not be used. Table 3 shows the recommended transformerVA
based on the PM014 output current.
Table 3. Transformer recommendations
PM014 output current Less than or equal to 0.7 Adc Greater than 0.7
Transformer VA (minimum) 40 75
10 BAS-SVX33F-EN
Pre-Installation
Recommended Configuration
The power supply module can be mounted onto a DIN rail as illustrated in Figure 2. Place DIN rail
end stops at each end of the configuration to prevent shifting of modules.
Figure 2. Correct horizontal mounting
PM014
24
VAC
XFMR
OUT
24
VAC
DIN rail
end stop
DIN rail
end stop Vent clearance
Vent clearance
1.8 in. min.
(4.6 cm)
1.8 in. min.
(4.6 cm)
Power supply
module
24 Vac input
connection
Inhaltsverzeichnis
Andere Trane Steuereinheit Handbücher
Trane
Trane TRACER SUMMIT BMTX-SVU01B-EN Bedienungsanleitung
Trane
Trane UNT-SVU011C Series Kurzanleitung
Trane
Trane VAV-UCM 4.2 Bedienungs- und Sicherheitshinweise
Trane
Trane TR200 MCB 105 Bedienungsanleitung
Trane
Trane VAV Bedienungsanleitung
Trane
Trane CNT06197 Montageanleitung
Trane
Trane TZON1050AC52ZA Bedienungsanleitung
Trane
Trane XL824 Bedienungsanleitung
Trane
Trane BAYLOAM105AA Montageanleitung
Trane
Trane Wireless Comm Montage- und Bedienungsanleitung
Trane
Trane CG-SVN01A-EN Bedienungsanleitung
Trane
Trane VariTrane Betriebsanleitung
Trane
Trane BAY4TXV1830A Montageanleitung
Trane
Trane 700 Bedienungsanleitung
Trane
Trane BAS-SVN213A-EN Bedienungsanleitung
Trane
Trane Symbio 700 FIAOPTN001 Series Bedienungsanleitung
Trane
Trane MERCURY EDAB 1105A Kurzanleitung
Trane
Trane RTHC-SVN02C-EN Bedienungsanleitung
Trane
Trane Belimo B2 Series Bedienungsanleitung
Trane
Trane AYSVPANL0022AA Series Montageanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
