Trane TR200 MCB 101 Bedienungsanleitung

Rev.2008-12-09130R0477 MI11B102 *MI11B102*

MCB 101 - General Purpose I/O

Option Module

Operating Instructions

December 2008

TR200

BAS-SVX28A-EN

Trane has a policy of continous product and product data improvement and reserves the right to

change design and specifications without notice.

www.trane.com

For more information, contact your local Trane

office or e-mail us at [email protected]

Literature Order Number BAS-SVX28A-EN

Date December 2008

Supersedes

Warnings, Cautions and Notices

Note that warnings, cautions and notices appear at appropriate intervals throughout this manual. Warnings are

provide to alert installing contractors to potential hazards that could result in personal injury or death. Cautions

are designed to alert personnel to hazardous situations that could result in personal injury, while notices indicate

a situation that could result in equipment or property-damage-only accidents.

Your personal safety and the proper operation of this machine depend upon the strict observance of these

precautions.

Warnings, Cautions and Notices appear at appropriate sections throughout this literature. Read these carefully.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. It could also

be used to alert against unsafe practices.

NOTICE

Indicates a situation that could result in equipment or property-damage only accidents.

Note

Indicates something important to be noted by the reader.

✮Indicates default setting

TR200 Series VFD General Purpose I/O Option Module MCB 101 Instruction 1

Introduction

This instruction describes the General Purpose I/O option MCB 101 for use in the TR200 expanding the number

of input/output in the frequency converter.

The MCB 101 option includes 3 digital inputs, 2 analog inputs, 2 digital outputs and 1 analog output.

SW firmware version to be installed in the drive control card must be version 3.00 or later versions for series,

and version 1.1x for TR200 series. Check par.15-43 Software Version for firmware version.

Code Numbers To Be Used At Ordering The Complete Kit For Upgrades

Standard version code no. 130B1125.

Coated version code no. 103B1212.

Illustration 1. 1: Parts for coated/non-coated code nos.

2 TR200 Series VFD General Purpose I/O Option Module MCB 101 Instruction

Galvanic Isolation in the MCB 101

Digital/analog inputs are galvanically isolated from other inputs/outputs on the MCB 101 and in the control card

of the frequency converter. Digital/analog outputs in the MCB 101 are galvanically isolated from other inputs/

outputs on the MCB 101, but not from these on the control card of the drive.

If the digital inputs 7, 8 or 9 are to be switched by use of the internal 24 V power supply (terminal 9) the connection

between terminal 1 and 5 which is illustrated in the drawing has to be established.

Illustration 1. 2: Principle Diagram

TR200 Series VFD General Purpose I/O Option Module MCB 101 Instruction 3

Digital Inputs - Terminal X30/1-4

Parameters for set-up: 5-16, 5-17 and 5-18

Number of

digital in-

puts

Voltage

level

Voltage levels Tolerance Max. Input impedance

30-24 V DC PNP type:

Common = 0 V

Logic “0”: Input < 5 V DC

Logic “0”: Input > 10 V DC

NPN type:

Common = 24 V

Logic “0”: Input > 19 V DC

Logic “0”: Input < 14 V DC

± 28 V continuous

± 37 V in minimum

10 sec.

Approx. 5 k ohm

Analog Voltage Inputs - Terminal X30/10-12

Parameters for set-up: 6-3*, 6-4* and 16-76

Number of analog voltage in-

puts

Standardized input

signal

Tolerance Resolu-

tion

Max. Input impe-

dance

20-10 V DC ± 20 V continuously 10 bits Approx. 5 K ohm

Digital Outputs - Terminal X30/5-7

Parameters for set-up: 5-32 and 5-33

Number of digital outputs Output level Tolerance Max.impedance

20 or 24 V DC ± 4 V ≥ 600 ohm

Analog Outputs - Terminal X30/5+8

Parameters for set-up: 6-6* and 16-77

Number of analog outputs Output signal level Tolerance Max.impedance

10/4 - 20 mA ± 0.1 mA < 500 ohm

4 TR200 Series VFD General Purpose I/O Option Module MCB 101 Instruction

Mounting of Option Modules in Slot B

The power to the frequency converter must be disconnected.

For A2, A3 and B3 enclosures:

• Remove the keypad, the terminal cover, and the keypad frame from the frequency converter.

• Fit the MCB 101 option card into slot B.

• Connect the control cables and relieve the cable by the enclosed cable strips.

Remove the knock out in the extended keypad frame delivered in the option set, so that the option

will fit under the extended keypad frame.

• Fit the extended keypad frame and terminal cover.

• Fit the keypad or blind cover in the extended keypad frame.

• Connect power to the frequency converter.

• Set up the input/output functions in the corresponding parameters, as mentioned in this document.

For A5, B1, B2, B4, C1, C2, C3, C4, D, E and F enclosures:

• Remove the keypad and the keypad cradle

• Fit the MCB 101 option card into slot B

• Connect the control cables and relieve the cable by the enclosed cable strips

• Fit the cradle

• Fit the keypad

A2, A3 and B3 enclosures A5, B1, B2, B4, C1, C2, C3, C4, D, E and F enclosures

TR200 Series VFD General Purpose I/O Option Module MCB 101 Instruction 5

Mounting Guidelines - Step By Step

These step-by-step instructions describe how to mount the control cables:

• The power to the frequency converter must be disconnected.

• Remove the keypad, the terminal cover, and the keypad frame from the frequency converter.

• Fit the MCB 101 option card into slot B.

• Connect the control cables and relieve the cable by the enclosed cable strips.

• Remove the knock out in the extended keypad frame, so that the option will fit under the extended

keypad frame.

• Fit the extended keypad frame and terminal cover.

• Fit the keypad or blind cover in the extended keypad frame.

• Connect power to the frequency converter.

•Set up the input/output functions in the corresponding parameters, as mentioned in the

Programming

Guide

How To Mount Cables

The graphic below illustrates how to mount the cables.

6 TR200 Series VFD General Purpose I/O Option Module MCB 101 Instruction

Rev.2008-12-09130R0477 MI11B102 *MI11B102*

MCB 101 - General Purpose I/O

Option Module

Operating Instructions

December 2008

TR200

BAS-SVX28A-EN

Trane has a policy of continous product and product data improvement and reserves the right to

change design and specifications without notice.

www.trane.com

For more information, contact your local Trane

office or e-mail us at [email protected]

Literature Order Number BAS-SVX28A-EN

Date December 2008

Supersedes

Inhaltsverzeichnis

Andere Trane Steuereinheit Handbücher

Trane

Trane XL824 Bedienungsanleitung

Trane

Trane Tracer MP503 Montage- und Bedienungsanleitung

Trane

Trane 700 Bedienungsanleitung

Trane

Trane ADAPTIVE CONTROL UCM-CLD Betriebsanleitung

Trane

Trane Symbio 700 FIAOPTN001 Series Bedienungsanleitung

Trane

Trane BAY4TXV1830A Montageanleitung

Trane

Trane VariTrane Betriebsanleitung

Trane

Trane VAV-UCM 4.2 Bedienungs- und Sicherheitshinweise

Trane

Trane RTHC-SVN02C-EN Bedienungsanleitung

Trane

Trane BAYLOAM105AA Montageanleitung

Trane

Trane CNT06197 Montageanleitung

Trane

Trane BAS-SVN213A-EN Bedienungsanleitung

Trane

Trane TZON1050AC52ZA Bedienungsanleitung

Trane

Trane TRACER SUMMIT BMTX-SVU01B-EN Bedienungsanleitung

Trane

Trane TCONT850 Bedienungsanleitung

Trane

Trane XL824 Bedienungsanleitung

Trane

Trane XL824 Bedienungsanleitung

Trane

Trane Tracer Summit Montageanleitung

Trane

Trane Wireless Comm Montage- und Bedienungsanleitung

Trane

Trane VAV Bedienungsanleitung

Trane

Trane Belimo B2 Series Bedienungsanleitung

Trane

Trane PM014 Montage- und Bedienungsanleitung

Trane

Trane AYSVPANL0022AA Series Montageanleitung

Trane

Trane UNT-SVU011C Series Kurzanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung