Trane RSDT1000F0AA Montage- und Bedienungsanleitung

Trane Rental Services

Fuel Tanks

Installation, Operation, and Maintenance

July 2020 SRV-SVX006B-EN

SAFETY WARNING

Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of

heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and training.

Improperly installed, adjusted or altered equipment by an unqualified person could result in death or serious injury.

When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that are

attached to the equipment.

Introduction

Read this manual thoroughly before operating or

servicing this unit.

Warnings, Cautions, and Notices

Safety advisories appear throughout this manual as

required. Your personal safety and the proper operation of

this machine depend upon the strict observance of these

precautions.

The three types of advisories are defined as follows:

WARNING Indicates a potentially hazardous

situation which, if not avoided, could

result in death or serious injury.

CAUTIONsIndicates a potentially hazardous

situation which, if not avoided, could

result in minor or moderate injury. It

could also be used to alert against

unsafe practices.

NOTICE Indicates a situation that could result in

equipment or property-damage only

accidents.

Important Environmental Concerns

Scientific research has shown that certain man-made

chemicals can affect the earth’s naturally occurring

stratospheric ozone layer when released to the

atmosphere. In particular, several of the identified

chemicals that may affect the ozone layer are refrigerants

that contain Chlorine, Fluorine and Carbon (CFCs) and

those containing Hydrogen, Chlorine, Fluorine and

Carbon (HCFCs). Not all refrigerants containing these

compounds have the same potential impact to the

environment. Trane advocates the responsible handling

of all refrigerants-including industry replacements for

CFCs such as HCFCs and HFCs.

Important Responsible Refrigerant

Practices

Trane believes that responsible refrigerant practices are

important to the environment, our customers, and the air

conditioning industry. All technicians who handle

refrigerants must be certified. The Federal Clean Air Act

(Section 608) sets forth the requirements for handling,

reclaiming, recovering and recycling of certain

refrigerants and the equipment that is used in these

service procedures. In addition, some states or

municipalities may have additional requirements that

must also be adhered to for responsible management of

refrigerants. Know the applicable laws and follow them.

WARNING

Proper Field Wiring and Grounding

Required!

Failure to follow code could result in death or serious

injury. All field wiring MUST be performed by qualified

personnel. Improperly installed and grounded field

wiring poses FIRE and ELECTROCUTION hazards. To

avoid these hazards, you MUST follow requirements for

field wiring installation and grounding as described in

NEC and your local/state electrical codes.

WARNING

Personal Protective Equipment (PPE)

Required!

Installing/servicing this unit could result in exposure to

electrical, mechanical and chemical hazards.

• Before installing/servicing this unit, technicians

MUST put on all PPE required for the work being

undertaken (Examples; cut resistant gloves/sleeves,

butyl gloves, safety glasses, hard hat/bump cap, fall

protection, electrical PPE and arc flash clothing).

ALWAYS refer to appropriate Material Safety Data

Sheets (MSDS)/Safety Data Sheets (SDS) and OSHA

guidelines for proper PPE.

• When working with or around hazardous chemicals,

ALWAYS refer to the appropriate MSDS/SDS and

OSHA/GHS (Global Harmonized System of

Classification and Labelling of Chemicals) guidelines

for information on allowable personal exposure

levels, proper respiratory protection and handling

instructions.

• If there is a risk of energized electrical contact, arc, or

flash, technicians MUST put on all PPE in accordance

with OSHA, NFPA 70E, or other country-specific

requirements for arc flash protection, PRIOR to

servicing the unit. NEVER PERFORM ANY

SWITCHING, DISCONNECTING, OR VOLTAGE

TESTING WITHOUT PROPER ELECTRICAL PPE AND

ARC FLASH CLOTHING. ENSURE ELECTRICAL

METERS AND EQUIPMENT ARE PROPERLY RATED

FOR INTENDED VOLTAGE.

Failure to follow instructions could result in death or

serious injury.

WARNING

Follow EHS Policies!

Failure to follow instructions below could result in

death or serious injury.

• All Trane personnel must follow the company’s

Environmental, Health and Safety (EHS) policies

when performing work such as hot work, electrical,

fall protection, lockout/tagout, refrigerant handling,

etc. Where local regulations are more stringent than

these policies, those regulations supersede these

policies.

• Non-Trane personnel should always follow local

regulations.

Introduction

SRV-SVX006B-EN 3

This document and the information in it are the property of

Trane, and may not be used or reproduced in whole or in

part without written permission. Trane reserves the right

to revise this publication at any time, and to make changes

to its content without obligation to notify any person of

such revision or change.

Trademarks

All trademarks referenced in this document are the

trademarks of their respective owners.

Revision History

4SRV-SVX006B-EN

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings, Cautions, and Notices . . . . . . . . 2

Important Environmental Concerns . . . . . 2

Important Responsible Refrigerant Practices

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Identification . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Model Number Description . . . . . . . . . . . . 6

Table 1. . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 1. . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation and Decommission . . . . . . . . . . . 7

Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Day Tank To Generator Hose Connections 9

Figure 2. Hand Nozzle . . . . . . . . . . . . . . . . 9

Figure 4. Female Quick Coupler to Threaded

End 9

Figure 3. Female to Male Quick Coupler. . . 9

Figure 5. Male Quick Coupler to Threaded End

Figure 6. Swivel-Type Coupling . . . . . . . . . 9

SRV-SVX006B-EN 5

Introduction

The purpose of this IOM is to detail the proper handing,

installation, and maintenance recommendations for Trane

Rental Services Fuel Tanks. This equipment has been

designed and manufactured for efficient refueling of

equipment and/or transportation of fuel. Full load lifting

eyes, forklift pockets and internal baffles allow handling of

the tank, while its double-walled design means any need

for spill pans are eliminated.

Identification

Each fuel tank is provided with a nameplate and labels

with the following information:

• Serial number

•Modelnumber

• Permissible pressures

• Permissible temperatures

•Weights

6SRV-SVX006B-EN

Specifications

Model Number Description

R S DT 1 0 0 0 F 0 A A

Rental Services prefix

Denotes day tank

Tank volume

Incremental designator

Design sequence

Table 1.

Specification RSDT1000F0

Capacity 950 gal

Double wall Yes

Day tank weight w/o fuel 2800 lb

Day tank weight with fuel 9400 lb

Height 48 in

Length 91 in

Width 87 in

Day tank hose sections six 25-ft sections

Fuel hose connection type Quick couple

Day tank supply & return One 1-in supply

One 1-in return

Lifting Fork or crane

Transfer pump hose length 25 ft

Transfer pump power 12V DC; 20 gpm

UL Certification UL142

Canadian UL Certification S601

Figure 1.

1. Hatch lid

2. Filler cap (3-in)

3. Electric pump

4. Fuel feed line/valve

5. Fuel return line/valve

6. Refueling hose

7. Relief vent

8. Fuel gauge

9. Fuel feed line/with ball valve

to fuel pump

SRV-SVX006B-EN 7

Installation and Decommission

Please read this document in its entirety before attempting

to off-load, install, or operate this tank.

Transportation

WARNING

Heavy Objects!

The lifting machinery and each of the cables (chains or

slings) used to lift the unit must be capable of

supporting the entire weight of the unit. Lifting cables

(chains or slings) may not be of the same length. Adjust

as necessary for even unit lift. Other lifting

arrangements could cause equipment or property

damage. Failure to follow the safety requirements in

this section could result in an improper lift, which could

result in death or serious personal injury, as well as

property damage.

1. Turn off pump (move lever down) and close generator

port valves.

2. Be sure filler cap is on and closed securely.

3. Be sure all outlets are securely closed/plugged with

plugs provided by the manufacturer.

4. Ensure outer tank is empty of spillage.

5. Close and padlock hatch to prevent vibration releasing

the catch.

6. Secure properly for transportation.

8SRV-SVX006B-EN

Operation

WARNING

Flammable Fluids!

Diesel fuel is flammable and poses a fire hazard. Do not

expose the fuel to excessive heat, pressure, or open

flames or sparks. Failure to follow the safety

requirements in this section could result in death or

serious personal injury, as well as property damage due

to fire or explosion.

WARNING

Safety Requirements!

Failure to follow the safety guidelines in this section

could result in death or serious personal injury.

• Use only for the transport of diesel fuel for refueling

equipment or standby generators.

• Keep the tank level when filling.

• Fill only with a hand-held trigger nozzle. Take special

care not to spill any fuel on the ground or in the

interstice.

• Do not smoke when refueling. Keep sparks flames and

hot material away from fuel and tank.

• Do not overfill; 95 percent is the maximum legal limit.

• Always replace filler cap and turn pump off (lever

down) when refueling finished.

• Store diesel hose and nozzle inside outer tank.

• Close all valve outlets and lock lid when transporting

on a public highway.

• Check for fluid in outer tank and empty regularly. Refer

to maintenance manual for detailed procedure.

If tank is used for refueling:

1. Place fuel tank in a place where it can be leveled as

much as possible.

2. Unlock and open hatch lid.

3. Pull out refueling hose and nozzle, see Figure 2 below.

4. Extend it to the tank to be refueled.

5. Connect female end of quick coupler into male end of

quick coupler on the pump discharge.

6. Open fuel feed line/valve on fuel tank.

7. Connect a power supply to the pump (minimum 20

amp rating).

8. Turn the pump on by lifting lever located on the side of

the pump.

9. Use the hand-held nozzle to transfer the fuel.

10. Fill to no more than 95 percent of capacity. This is the

maximum allowed in order to account for fuel

expansion. Do not overfill.

11. Turn the pump off when the refueling is completed.

If tank is used as constant fuel supply:

Supply

1. Place fuel tank in a place where it can be leveled as

much as possible.

2. Connect female quick-coupler (See Figure 3) into feed

line on fuel tank.

3. Extend as much hose as required.

4. Connect swivel-type coupling (See Figure 6 below)

into generator supply connection.

5. Screw in female quick-coupler with threaded end hose

(See Figure 4) into swivel coupler. .

6. Make sure to bleed air from system.

Return

1. Connect male quick-coupler into the return line on the

fuel tank.

2. Extend as much hose as required.

3. Connect swivel-type coupling into generator return

connection.

4. Screw in male quick-coupler with threaded end hose

(See Figure 5) into swivel coupler.

Note: Make sure valves on generator fuel tank are placed

so that it draws fuel out of fuel reservoir.

Note: These recommendations are written for a

generator with a 1-inch NPT female thread to attach

into. Alternate connections will require adapters to

be supplied by the customer.

Tip: When performing installation of hoses it is

considered good practice to start at the Fuel Tank

and work your way to the Generator connections.

Operation

SRV-SVX006B-EN 9

Day Tank To Generator Hose Connections

Figure 2. Hand Nozzle

Figure 4. Female Quick Coupler to Threaded End



Figure 3. Female to Male Quick Coupler

Figure 5. Male Quick Coupler to Threaded End

Figure 6. Swivel-Type Coupling

Inhaltsverzeichnis

Andere Trane Tankausrüstung Handbücher

Trane

Trane RSDT1000F0 Montage- und Bedienungsanleitung

Beliebte Tankausrüstung Handbücher anderer Marken

ARKSEN

ARKSEN 002-AU-30035/GAS35 Bedienungsanleitung

morse

morse 185G Bedienungsanleitung

IVT

IVT LATENTO XXL Series Benutzerhandbuch

Clayton

Clayton WartHog 603-105W Leitfaden

Vetus

Vetus FTL3808B Kurzanleitung

Astro Pneumatic Tool

Astro Pneumatic Tool PT2-4 Bedienungsanleitung

SII

SII 99800088 Bedienungsanleitung

Gardena

Gardena 4000/5 eco Bedienungsanleitung

CALEFACTIO

CALEFACTIO GMP Bedienungsanleitung

Amtrol

Amtrol FILL-TROL FT-109 Montageanleitung

Graf

Graf 160470 UPone 3 EW, 2000 L Bedienungsanleitung

VIAIR

VIAIR 90011 Bedienungsanleitung

Flexcon

Flexcon FLU/H2PLU Bedienungsanleitung

Harbor Freight Tools

Harbor Freight Tools Centralpneumatic 66839 Montageanleitung

DeVilbiss

DeVilbiss QM T-5 Series Referenzhandbuch

Regulus

Regulus PS 80 Z Bedienungsanleitung

KIESELMANN

KIESELMANN TDAM 6180 Bedienungsanleitung

Worthington

Worthington Amtrol THERM-X-TROL ST-447C Montageanleitung