Transcell Technology TC-100 Series Benutzerhandbuch

TC-100 Series

Digital Scale

Setup Manual

Revision 1.0

January 10, 2003

Contents subject to change without notice.

Transcell Technology, Inc.

975 Deerfield Parkway

Buffalo Grove, IL 60089

Tel (847) 419-9180

Fax (847) 419-1515

E-mail: [email protected]

Web: www.transcell.net

TABLE OF CONTENTS

Page

Chapter 1: Introduction To The TC-100 Series Setup Manual ....................................................... 1-1

Chapter 2: Installation ..................................................................................................................... 2-1

2.1 Overview ....................................................................................................................... 2-1

2.1.1 Connecting the serial printer, remote display or computer.............................. 2-1

2.1.2 Connecting the power supply........................................................................... 2-1

Chapter 3: Configuration................................................................................................................. 3-1

3.1 Configuration Overview................................................................................................. 3-1

3.2 Setup (“F”) Menu........................................................................................................... 3-1

3.2.1 Entering the Setup Menu ................................................................................. 3-1

3.2.2 Navigating in the Setup Menu.......................................................................... 3-1

3.2.3 Notes on the Setup Menu ................................................................................ 3-2

3.2.4 Exiting the Setup Menu ................................................................................... 3-2

3.3 User (“A”) Menu............................................................................................................. 3-2

hapter 4: Setup Menu Descriptions and Procedures ................................................................... 4-1

4.1 Setup Menu Descriptions.............................................................................................. 4-1

4.2 Resetting Factory Defaults............................................................................................ 4-2

hapter 5: User Menu Descriptions and Procedures..................................................................... 5-1

5.1 User Menu Descriptions................................................................................................ 5-1

hapter 6: Calibration..................................................................................................................... 6-1

6.1 Calibration Overview..................................................................................................... 6-1

6.2 Zero Calibration (F16)................................................................................................... 6-1

6.3 Span Calibration (F17).................................................................................................. 6-1

LIST OF FIGURES

2-1 TC-100 Rear Panel................................................................................................................. 2-1

3-1 Setup Menu Key Assignments................................................................................................ 3-1

3-2 Setup Menu Chart................................................................................................................... 3-2

3-3 User Menu Key Assignments.................................................................................................. 3-5

LIST OF TABLES

4-1 Factory Restore Key ............................................................................................................... 4-2

CHAPTER 1: INTRODUCTION TO THE TC-100 SERIES SETUP MANUAL

Your Model TC-100 Series Digital Scale is a complete scale and has been configured and cali-

brate installed for you at the factory. This manual is intended for the dealer or end user who

wishes to customize the scale’s configuration.

The scale's installation and wiring instructions are found in Chapter 2. The scale contains two

main setup menus: The Setup (“F”) menu, which configures the Scale to your weigh platform and

the User (“A”) menu, which configures the serial communication port and enables some user op-

tions. Chapter 3 gives an overview and explains how to use the five front panel keys to maneuver

and save settings in both menus. Chapters 4 and 5 explain the Setup and User Menu options,

respectively. Chapter 6 covers system calibration. Prior to installing the Scale, please read this

manual carefully and completely. Store the manual in a safe and convenient place so it will be

available if you have questions concerning the setup and operation of the scale.

Page 1-1

CHAPTER 2: INSTALLATION

2.1 OVERVIEW

The rear panel contains all connectors necessary to make the appropriate connections to the serial

peripheral and power supply.

COM1 SERIAL

PORT (RS-232)

POWER

CONNECTOR

ON/OFF

SWITCH

Figure 2-1: TC-100 Rear Panel

2.1.1 CONNECTING THE SERIAL PRINTER, REMOTE DISPLAY OR COMPUTER

The TC-100 series Scale comes standard with one serial port, designated COM1. COM1 is

a full duplex, RS-232 port designed for connection to either a PC or a serial printer. It can

also be connected to a simplex device such as a remote display.

COM1 is wired to a physical connector, a D-SUB9 female. Refer to the TC-100 Operation

Manual (Appendix B) for some suggested cable diagrams. (A 9-pin pin Male D-type

connector is required).

2.1.2 CONNECTING THE POWER SUPPLY

1. The Scale ships standard with an external AC to DC adapter. Simply plug the AC

adapter into the Scale’s DC Power Jack first, and then plug into a standard wall outlet.

Make sure that the AC voltage appearing at the wall outlet matches the input

voltage marked on the AC adapter.

Page 2-1

CHAPTER 3: CONFIGURATION

3.1 CONFIGURATION OVERVIEW

The scale contains two main setup menus: The Setup (“F”) menu, which configures the scale to

your weigh platform and the User (“A”) menu, which configures the serial communication port and

enables some user options. TheSetupand User menus consist of several menu selections, each with its

own sub-menu of choices.

To set up the scale, you must first enter the appropriate menu mode. Once there, four of the front panel keys

become directional navigators to move around in the menus, and one key is used to save or SET the

selections.

3.2 SETUP (“F”) MENU

3.2.1 ENTERING THE SETUP MENU

1. Power off the scale by toggling the ON/OFF switch.

2. Press and hold the numeric 0 key while powering the scale back on. When the scale

shows ” F 1” , you are in Setup Menu mode and you may release the 0 key.

3.2.2 NAVIGATING IN THE SETUP MENU

Use the directional keys shown in Figure 3-1 to move around in the Setup Menu Chart

shown in Figure 3-2 on the following page. Detailed descriptions of the Setup Menu can be

found in Chapter 4.

1. To move to a new “F” heading, use the Print (left) or 9 (right) key to move right or left

in the Setup Menu Chart.

2. To move to the selection level, press the 6 (down) key once. The current saved

selection is shown.

3. To view the available selections for the current “F” heading, use the Print (left) or 9

(right) key to move through the selection field.

4. To save a new selection, press the SAMPLE / SAVE (Set) key. To exit without saving,

press the 3 (up) key to return to the current “F” heading.

5. Repeat Steps 2 through 5 until the Setup Menu is programmed.

SETUP MENU MODE KEY FUNCTIONS

6SAMPLE 9

SET

3PRINT

Figure 3-1: Setup Menu Key Assignments

Continued =>

Page 3-1

Grads F8

Calib. Unit F9

Dsp. Div.

lb kg

10000

0d ... 5d

Zero Band

125

F10

Dec. Pt.

F17

Span Calib.

Press ZERO

key to begin

F22

Creep Band F23

Creep Time

0.0 ... 0.0000

F16

Zero Calib.

Press ZERO

key to begin

OFF ... 50 1 ... 30

Figure 3-2: Setup Menu Chart

3.2.3 NOTES ON THE SETUP MENU

1. Detailed descriptions of the setup menu parameters can be found in Chapter 5 of this

manual.

3.2.4 EXITING THE SETUP MENU

. Power off the scale by toggling the ON/OFF switch.

2. Power on the scale as normal. The display will go through a digit check, then settle into

Normal Operating mode. All front panel keys will now return to their normal mode of

operation.

3.3 USER (“A”) MENU

The User Menu is covered extensively in the TC-100 Operation Manual.

Page 3-2

Page 4-1

CHAPTER 4: SETUP MENU DESCRIPTIONS AND PROCEDURES

4.1 SETUP MENU DESCRIPTIONS

This section provides more detailed descriptions of the selections found in the Setup Menu Chart.

Factory-set defaults are shown in bold with a checkmark (√).

NAME/CODE DESCRIPTION CODE/VALUE

Graduations Specifies number of full-scale graduations. Value should be consis-

tent with legal requirements and environmental limits on the useful

system resolution.

10,000√

Zero Track

Band

Selects the range within which the scale will automatically zero. Note

that the scale must be in standstill to automatically zero. Selections

are in Display Divisions.

0.1d

0.3d

0.5d√

Calib. Unit Selects the primary base unit to be used in the calibration process.

Also the default unit for normal operation.

"1" = primary unit is lb. "2" = primary unit is in kg.

√depends on

model

Display

Divisions

Determines the desired weight increments. Value should be consis-

tent with legal requirements. 1

√depends on

model

F10

Decimal Pt. Determines location of the decimal point. 0.0

0.000 0.0000

√depends on

model

F16

Zero Calibra-

tion

Places indicator into the zero calibration routine. Scrolling down with

the 6key one level begins the procedure. Press 6key to

begin sequence

F17

Span Calibra-

tion

Places indicator into the span calibration routine. Scrolling down with

the 6key one level begins the procedure. Press 6key to

begin sequence

F22

Creep Track-

ing Band

Determines the creep tracking band in scale divisions. OFF√

10 15 20

25 30 50

F23

Creep Track-

ing Time

Determines the creep tracking time in seconds. 1 2 3 4 5√

10 20 30

Page 4-2

4.2 RESETTING FACTORY DEFAULTS

This section provides instructions for restoring factory default settings for each model.

1. Turn off the scale by toggling the ON/OFF switch.

2. Look up the key in Table 4-1 below corresponding to your model.

3. Press and hold that key while switching the scale back on. You may release that key

when the scale displays the corresponding message found in Table 4-1.

MODEL CAPACITY / GRADUATION KEY MESSAGE

TC-100-2 2 lb x 0.0002 lb 1 INIT 2

TC-100-5 5 lb x 0.0005 lb 2 INIT 5

TC-100-10 10 lb x 0.001 lb 3 INIT10

TC-100-20 20 lb x 0.002 lb 4 INIT20

TC-100-1M 1000 g x 0.1 g 5 INI 1-

TC-100-2M 2000 g x 0.2 g 6 INI 2-

TC-100-5M 5000 g x 0.5 g 7 INI 5-

TC-100-10M 10,000 g x 1 g 9 INI10-

Table 4-1: Factory Restore Key

Page 5-1

CHAPTER 5: USER MENU DESCRIPTIONS AND PROCEDURES

5.1 USER MENU DESCRIPTIONS

Please refer to Chapter 5 of the TC-100 Operation Manual.

Page 6-1

CHAPTER 6: CALIBRATION

6.1 CALIBRATION OVERVIEW

The scale is calibrated by following the procedures embedded in F16 (Zero) and F17 (Span) of the

Setup Menu. Each procedure enters a value into the scale's non-volatile memory - F16 the zero

value (deadweight) and F17 the span value (test weight). The minimum test weight that can be

used is 1% of full-scale capacity.

NOTE: This chapter assumes that the scale is in Setup (“F”) Menu mode. If the scale is not in

Setup Menu mode, refer to Chapter 3 for instructions.

6.2 ZERO CALIBRATION (F16)

1. While in the Setup mode, scroll to "F 16", then scroll down once using the 6 key to enter zero

calibration menu. The display will momentarily show "C 0" followed by a value. This value is the

internal A/D count and can prove useful when trying to troubleshoot setup problems.

2. After making sure that there are no test weights on the platform, press the ZERO key to zero

out the displayed value.

3. Press the SAMPLE/SAVE key to save the zero point value. The display will show "EndC0"

momentarily, then revert back up to F16. At this time, proceed to the F17 span calibration to

complete scale calibration.

6.3 SPAN CALIBRATION (F17)

1. While in the Setup mode, scroll to "F 17", then scroll down once using the 6 key to enter span

calibration menu.

2. The display will momentarily show "C 1" for the span calibration, followed by a value with one

flashing digit. This value will be zero with the Decimal Point parameter selected in F10. Place the

test weight on the platter.

3. Use the numeric keys to enter the test weight value. Please note that the decimal point is fixed so

that if you are entering, for example, 2 lb, you need to type “2” followed by zeroes until the “2” is

to the left of the decimal point.

4. After setting the exact value, press the SAMPLE/SAVE key to save the value.

5. If the calibration was successful, the display will show "EndC1" momentarily, then revert back up

to F17.

6. If the calibration was not successful, one of the error messages below will appear. Take the

indicated action to correct the problem, then perform a new calibration.

"Err0" - The calibration test weight or the adjusted keyed-in weight is larger than the full

capacity of the scale. Change the calibration test weight or check the input data.

"Err1" - The calibration test weight or the adjusted keyed-in weight is smaller than 1% of the full

capacity of the scale. Change the calibration test weight or check the input data.

"Err2" - The internal resolution of the scale is not high enough to accept the calibration value.

Andere Handbücher für TC-100 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Transcell Technology Skala Handbücher

Transcell Technology

Transcell Technology SPS-5 Bedienungsanleitung

Transcell Technology

Transcell Technology PC 150 Stücklistenhandbuch

Transcell Technology

Transcell Technology SPS-70 Bedienungsanleitung

Transcell Technology

Transcell Technology TC-200-6 Bedienungsanleitung

Transcell Technology

Transcell Technology SPS-30 Plus Bedienungsanleitung

Transcell Technology

Transcell Technology SPC-150 Bedienungsanleitung

Transcell Technology

Transcell Technology ESW SERIES Bedienungsanleitung

Transcell Technology

Transcell Technology Neptune-6500 Series Bedienungsanleitung

Transcell Technology

Transcell Technology EL 3000 Bedienungsanleitung

Transcell Technology

Transcell Technology NEPTUNE-5500 Series Bedienungsanleitung

Transcell Technology

Transcell Technology tcs3t series Bedienungsanleitung

Transcell Technology

Transcell Technology PC 150 Bedienungsanleitung

Transcell Technology

Transcell Technology CS Series Bedienungsanleitung

Transcell Technology

Transcell Technology SPL Series Bedienungsanleitung

Transcell Technology

Transcell Technology TC-100 Series Bedienungsanleitung

Transcell Technology

Transcell Technology PC35 Bedienungsanleitung

Transcell Technology

Transcell Technology DCSG series Technisches Handbuch

Transcell Technology

Transcell Technology TC-2010 Series Stücklistenhandbuch

Transcell Technology

Transcell Technology SPS-30 Bedienungsanleitung

Transcell Technology

Transcell Technology TC-2005 Series Stücklistenhandbuch

Transcell Technology

Transcell Technology TC-2010 Series Stücklistenhandbuch

Transcell Technology

Transcell Technology WB-5040-SWP Bedienungsanleitung

Transcell Technology

Transcell Technology TI-500E SS Bedienungsanleitung

Transcell Technology

Transcell Technology SRP-300 Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung