Transition Networks CSDTF1011-105 Bedienungsanleitung

Installation . . . . . . . . . . . . . . . . . . . . .3

Operation . . . . . . . . . . . . . . . . . . . . . .9

Cable Specifications . . . . . . . . . . . . .10

Technical Specifications . . . . . . . . . .12

Troubleshooting . . . . . . . . . . . . . . . .13

Compliance Information . . . . . . . . .16

* Typical maximum cable distance. Actual

distance is dependent upon the physical

characteristics of the network

Note: The CSDTF10xx-10x requires a CSU

between theDevice and the Public

Telephone Network.

CSDTF1027-105 RJ-45

1.5 km (5,000 feet)*

ST, 1300 nm multimode

5 km (3.1 miles)*

Part Number Port One - Copper Port Two - Duplex Fiber-Optic

CSDTF1011-105 RJ-45

1.5 km (5,000 feet)*

ST, 850 nm multimode

2 km (1.2 miles)*

CSDTF1012-105 RJ-45

1.5 km (5,000 feet)*

ST, 1310 nm single mode

8 km (4.8 miles)*

CSDTF1013-105 RJ-45

1.5 km (5,000 feet)*

SC, 850 nm multimode

2 km (1.2 miles)*

CSDTF1014-105 RJ-45

1.5 km (5,000 feet)*

SC, 1310 nm single mode

20 km (12.4 miles)*

CSDTF1015-105 RJ-45

1.5 km (5,000 feet)*

SC, 1310 nm single mode

40 km (24.8 miles)*

CSDTF1016-105 RJ-45

1.5 km (5,000 feet)*

SC, 1310 nm single mode

60 km (37.3 miles)*

CSDTF1017-105 RJ-45

1.5 km (5,000 feet)*

SC, 1550 nm single mode

80 km (49.7 miles)*

CSDTF1018-105 RJ-45

1.5 km (5,000 feet)*

MT-RJ, 1300 nm multimode

2 km (1.2 miles)*

CSDTF1022-105 RJ-45

1.5 km (5,000 feet)*

ST, 1310 nm single mode

15 km (9.3 miles)*

CSDTF1025-105 RJ-45

1.5 km (5,000 feet)*

MT-RJ, 1310 nm single mode

20 km (12.4 miles)*

User’s Guide

CSDTF10xx-10x

Slide-in-Module Devices

• T1 / E1 with Remote Management

• Copper to Fiber

Transition Networks CSDTF10xx-10x series Devices, designed

to be installed into the Transition Networks PointSystem™

chassis, encode and decode T1 or E1 twisted-pair copper

signals over fiber optic cable to extend the distance and

transmission reliability of high-speed T1 or E1 data traffic. The

device is framing independent (as ESF vs. D4) and supports all common line codes (e.g.,

AMI, B8ZS, HDB3).

The CSDTF10xx-10x is designed to be installed in pairs. For example, install one

CSDTF1011-105 as the “local” Device and another CSDTF1011-105 as the “remote”

Device.

224-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

CSDTF10xx-10x

(TX) = transmit (RX) = receive

* Typical maximum cable distance. Actual distance is dependent upon the physical

characteristics of the network.

** CSDTF1029-105 and -106 are intended to be installed in the same network where

one is the localDevice and the other is the remoteDevice.

*** CSDTF1029-107 and -108 are intended to be installed in the same network where

one is the localDevice and the other is the remoteDevice.

Part Number Port One - Copper Port Two - Single Fiber Optic

CSDTF1029-105 ** RJ-45

1.5 km (5,000 feet)*

SC, 1310 mn (TX)/1550 nm (RX)

single mode, 20 km (12.4 miles)*

CSDTF1029-106 ** RJ-45

1.5 km (5,000 feet)*

SC, 1550 mn (TX)/1310 nm (RX)

single mode, 20 km (12.4 miles)*

CSDTF1029-107 *** RJ-45

1.5 km (5,000 feet)*

SC, 1310 mn (TX)/1550 nm (RX)

single mode, 40 km (24.8 miles)*

CSDTF1029-108 *** RJ-45

1.5 km (5,000 feet)*

SC, 1550 mn (TX)/1310 nm (RX)

single mode, 40 km (24.8 miles)*

Note: The SSDTF10xx-10x model is the stand-alone version of the Device. For more

information, see the SSDTF10xx-10x user’s guide on-line at:

www.transition.com.

[email protected] -- Click the “Transition Now” link for a live Web chat. 3

Installation

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when setting the jumper and switches. Failure to observe this caution

could result in damage to, and subsequent failure of, the Device.

Set the Hardware/Software Jumper

• The hardware/software jumper is located on the circuit board and is labeled

“H” and “S”.

• Use a small needle-nose pliers or similar device to move the jumper to the

desired position.

Hardware The Device mode is determined by the

switch settings.

Software The Device mode is determined by the

most-recently saved, on-board

microprocessor settings.

Set the MDI/MDI-X switch (hardware mode only)

The MDI/MDI-X switch is located on the side of the Device. This switch allows the

network administrator to use straight-through cable in installations where crossover

configuration cable is required. Use a small flat-blade screwdriver or a similar

device to set the recessed switch.

Set the switch to MDI if using

straight-through copper cable to

connect two unlike devices.

Set the switch to MDI-X if using

crossover copper cable to connect

two like devices.

Hardware Mode

Software Mode

MDI MDI-X

RTIP

RRING

TTIP

TRING

TTIP

TRING

RTIP

RRING

RTIP

RRING

TTIP

TRING

TTIP

TRING

RTIP

RRING

Straight-Through Cable Crossover Cable

secivedekilnurofrotcennoCsecivedekilnurofrotcennoC

Twisted Pair #1

Twisted Pair #2

Twisted Pair #1

Twisted Pair #2

TN Device TN Device

424-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

CSDTF10xx-10x

Installation -- Continued

Set the loop-back switch

Hardware mode:

The loop-back switch is located on the front panel of the Device and is used for

installation and network debugging procedures.

To set the switch, use a small flat-blade screwdriver or a

similar device (see the drawing to the right).

CL (Copper loop-back) Enable loop-back on the local copper interface.

-- (Center position) Normal operation.

FL (Fiber loop-back) Enable loop-back on the local fiber interface.

Software Mode:

If both Devices are under software control, the network administrator can initiate

the loop-back test function on the copper interface (local or remote) or on the fiber

interface (local or remote). These four loop-back test scenarios are described in

detail on page 14.

Set the configuration switches

The configuration switches are located on the side of the Device and are used to

configure the Device for various network conditions.

There are two sets (“left” is SW 2, and “right” is SW 1) each with four switches

labeled “1” through “4” as shown below.

Use a small, flat-blade screwdriver or a similar device to set the recessed switches.

Transmit all ones (switches 1 & 2 of SW 2)

The transmit all ones function allows the insertion of an “all ones” pattern on the

copper and/or fiber interface when the signal detect is lost, creating an alarm

condition at the device connected to the interface.

Switch 1. Copper -- transmit all ones

UP - Disables the transmit all ones function

on the copper interface.

DOWN - Transmits an “all ones” pattern on

the copper interface when the signal detect

on the fiber interface is lost.

CL FL

SW 2 SW 1

Rear Cable End

Config

Switches

1 2 3 4 1 2 3 4 Switch Numbers

Key:

DOWN

Not Used

1234

Coax - Transmit All Ones - Disabled

Coax - Transmit All Ones - Enabled

[email protected] -- Click the “Transition Now” link for a live Web chat. 5

Installation -- Continued

Switch 2. Fiber -- transmit all ones

UP - Disables the transmit all ones function

on the fiber interface.

DOWN - Transmits an “all ones” pattern on

the fiber interface when the signal detect on

the copper interface is lost.

Select T1 configuration (switches 3 & 4, left set)

Use switches 3 and 4 to configure the Device for T1 configuration.

Switch 3. long haul/short haul (T1 only)

UP - Short haul.

DOWN - Long haul.

Switch 4. T1 / E1

UP - T1 configuration.

Set switches 1, 2, 3, and 4 on the right set

for the required network cable settings

(see pages 6 and 7).

Select E1 configuration (switch 4, left set)

Use switch 4 to configure the Device for E1 configuration.

Switch 4. T1 / E1

DOWN- E1 configuration.

The default network cable setting is 3.0 V,

120 ohm.

Switch 3 on the left set and switches 1, 2, 3,

and 4 on the right set are disabled.

1234

Fiber - Transmit All Ones - Disabled

Fiber - Transmit All Ones - Enabled

1234

Short Haul (T1 only)

Long Haul (T1 only)

T1 Configuration

12344

123434

E1 — 3.0V 120 Ohm Cable

624-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

CSDTF10xx-10x

Installation -- Continued

T1/short-haul signal

Use switches 3 and 4 on the left switch set to select T1/short-haul signal (see the

drawing below).

Use switches 1, 2 and 3 on the right switch set to select the proper network cable

settings. The drawing below lists the seven options.

DSX-1 121.6 - 162.5 m

(399 - 533') 100 ohm cable

DSX-1 81 - 121.6 m

(266 - 399') 100 ohm cable

DSX-1 40.5 - 81 m

(133 - 266') 100 ohm cable

DSX-1 0 - 40.5 m

(0 - 133') ANSI T1.403

100 ohm cable

DSX-1 6.0V

100 ohm cable

DSX-1 0 - 40.5 m

(0 - 133') 100 ohm cable

DSX-1 162.5 - 200 m

(533 - 655') 100 ohm cable

34 123

(T1/Short Haul)

(Switch 4 on the right switch set is not

used for configuring T1/short-haul

signals.)

[email protected] -- Click the “Transition Now” link for a live Web chat. 7

Installation -- Continued

Set the cable settings forT1 configuration (right switch set)

T1/long-haul signal

Use switches 3 and 4 on the left switch set to select T1/long-haul signal (see the

drawing below).

Use switches 1 and 2 on the right switch set to select the proper network cable

settings. The drawing below lists the four options.

(Switches 3 and 4 on the right

switch set are not used for

configuring T1 / long-haul signals.)

-15.0 db 100 ohm cab

-7.5 db 100 ohm cabl

-22.5 db 100 ohm cab

34 12

0.0 db 100 ohm cable

(T1/Long-Haul)

Install the slide-in-module

CAUTION: Wear a grounding device and observe electrostatic discharge precautions

when installing the CSDTF10xx-10x slide-in-module Device. Failure to observe this

caution could result in damage to, and subsequent failure of, the Device.

1. Carefully slide the slide-in-module into the installation slot, aligning the

module with the installation guides.

2. Ensure that the module is firmly seated inside the chassis.

3. Push in and rotate the attached panel fastener screw clockwise to secure the

module to the chassis front.

Media Converter

Point System Chassis

Panel Fastener

Slot

824-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

CSDTF10xx-10x

Installation -- Continued

Install the copper cable

1. Locate or build twisted-pair copper cables that are compliant with the

specifications on page 11 with RJ-45 connectors at both ends.

2. Ensure that the MDI/MDI-X switch is set according to the network conditions

(see page 3).

3. Connect the RJ-45 connector at one end of cable to the RJ-45 port on the

Device.

4. Connect the RJ-45 connector at the other end of the cable to the RJ-45 port on

the other device (switch, workstation, etc.).

RJ-45 port

on the other device

(switch, work station, etc

RJ-45 port

on the media

converter

Install the fiber cable

1. Locate or build fiber cables with male, two-stranded TX to RX connectors

installed at both ends.

2. Connect the fiber cables to the local CSDTF10xx-10x Device as described:

• Connect the male TX cable connector to the female TX port.

• Connect the male RX cable connector to the female RX port.

3. Connect the fiber cables to the remote CSDTF10xx-10x Device as described:

• Connect the male TX cable connector to the female RX port.

• Connect the male RX cable connector to the female TX port.

Connect fiber cable

to media converter

as shown.

Connect fiber cable

to other device

(media converter,

hub, etc.) as shown

RX TX

[email protected] -- Click the “Transition Now” link for a live Web chat. 9

Operation

After installation, the Device should function without operator intervention. Use the

LEDs to monitor theDevice operation in the network.

SDC (Signal Detect/Copper) ON = the copper link is up.

SDF (Signal Detect/Fiber) ON = the fiber link is up.

PWR (Power) ON = the Device is connected to

external power.

Dry-contact relay

The RJ-45 copper port has a dry-contact relay that

opens if the power, signal detect/copper, or signal

detect/fiber are lost. The operational rating on pins

3 and 6 are 0-30VDC, 100mA (max).

Remote management function

A remote stand-alone Device (revision SSDTF10xx-105 or higher) can be managed

when connected to a local CSDTF10xx-105 Device. Please note that in a managed

network, both the local and remote Devices must be set to “software” mode (see

page 3).

SNMP

Use SNMP at an attached terminal or at a remote location to monitor the Device by

monitoring:

•Device power and hardware switch settings

• Copper link and fiber link status (local and/or remote)

• AIS detected on copper link and fiber link (local and/or remote)

Also, use SNMP to enter network commands that:

• Bootload the firmware (local only)

• Enable/disable loop-back on the copper link (local and/or remote)

• Enable/disable loop-back on the fiber link (local and/or remote)

• Enable/disable Transmit All Ones on the fiber link when the copper link

is down (local and/or remote)

• Enable/disable Transmit All Ones on the copper link when the fiber link

is down (local and/or remote)

• Power-down the Device

See the on-line documentation that comes with Transition Networks FocalPoint™

software for commands and usage at www.transition.com.

Relay

RJ-45 Connect

CSDTF

Fiber

SDFSDC PWR

CL FL

UTP/STP

10 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

CSDTF10xx-10x

Cable Specifications

Fiber Cable

single mode fiber (recommended): 9 µm

Multimode fiber (recommended): 62.5/125 µm

Multimode fiber (optional): 100/140, 85/140, 50/125 µm

CSDTF1011-105 850 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm

Link Budget: 13.5 dB

CSDTF1012-105 1310 nm single mode

Fiber-optic Transmitter Power: min: -27.0 dBm max: -10.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -14.0 dBm

Link Budget: 7.0 dB

CSDTF1013-105 850 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm

Link Budget: 13.5 dB

CSDTF1014-105 1310 nm single mode

Fiber-optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -3.0 dBm

Link Budget: 15.0 dB

CSDTF1015-105 1310 nm single mode

Fiber Optic Transmitter Power: min: -8.0 dBm max: -2.0 dBm

Fiber Optic Receiver Sensitivity: min: -38.0 dBm max: -8.0 dBm

Link Budget: 30.0 dB

CSDTF1016-105 1310 nm single mode

Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm

Fiber-optic Receiver Sensitivity: min: -38.0 dBm max: -8.0 dBm

Link Budget: 33.0 dB

CSDTF1017-105 1550 nm single mode

Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 29.0 dB

CSDTF1018-105 1300 nm multimode

Fiber-optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber-optic Receiver Sensitivity: min: -33.5 dBm max: -14.0 dBm

Link Budget: 14.5 dB

CSDTF1022-105 1310 nm single mode

Fiber Optic Transmitter Power: min: -15.0 dBm max: -5.0 dBm

Fiber Optic Receiver Sensitivity: min: -25.0 dBm max: -14.0 dBm

Link Budget: 10.0 dB

CSDTF1025-105 1310 nm single mode

Fiber-optic Transmitter Power: min: -11.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm

Link Budget: 9.0 dB

[email protected] -- Click the “Transition Now” link for a live Web chat. 11

Cable Specifications -- Continued

Fiber cable

CSDTF1027-105 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -15.0 dBm

Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm

Link Budget: 13.5 dB

CSDTF1029-105 1310 nm (TX) / 1550 nm (RX) simplex

Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

CSDTF1029-106 1550 nm (TX) / 1310 nm (RX) simplex

Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

CSDTF1029-107 1310 nm (TX) / 1550 nm (RX) simplex

CSDTF1029-108 1550 nm (TX) / 1310 nm (RX) simplex

Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm

Link Budget: 25.0 dB

The fiber optic transmitters on this device meet Class I Laser safety requirements

per IEC-825/CDRH standards and comply with 21 CFR1040.10 and

21CFR1040.11.

Copper cable

Connector: RJ-45 / RJ-48C

Elec. network connection: Single 4-wire (Tip/Ring - Tip1/Ring1)

Mechanical arrangement: 8-position miniature modular jack

Usage: 1.544 Mb/s or 2.0478 Mb/s access lines

Interface codes: 04DU9 (any applicable)

Cable type:

Long Haul T1: 0db, -7.5dp, -15db, -22db

E1 (120 ohm): E1 3.0V, 120

J1 (110 ohm): 0-655’, 110

DSX-1 (100 ohm): 0-133’, 133-266’, 266-399’,

399-533’, 533-655’

Dry Contact B

Transmit

Dry Contact

Receive

(ring) R

(tip) T

(ring) R1

(tip) T1

(not used)

12 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

CSDTF10xx-10x

Technical Specifications

For use with Transition Networks Model CSDTF10xx-10x or equivalent

Standards: Emissions: CISPR A; Telecordia TR-NWT-001089

(designed to meet; NOT tested); FCC Part 68; T1/E1

Physical layer: ITU-T, ANSI, AT&T, and ETSI; European

Technical Standard: TBR 12; British Technical

Publication: PD 7024 : 1994 (NTR 4)

Dimensions: 3.4" x 5" x 0.87" (86 mm x 182 mm x 22 mm)

Weight: 3 oz. (91 g) approximately

Power Consumption: 3.7 Watts

MTBF: 342,000 (MIL217F2 V5.0) (MIL-HDBD-217F)

933,000 (Bellcore7 V5.0)

Environment: 0°C to 60°C (32°F to 140° F )

Storage Temp: -15°C to 65°C (5°F to 149°F)

Humidity: 10% to 90%, non condensing

Altitude: 0 to 10,000 feet

Warranty: Lifetime

*Manufacturer’s rated ambient temperature: Tmra range for this slide-in-module

depends on the physical characteristics and the installation configuration of the

Transition Networks PointSystem™ chassis in which this slide-in-module will be

installed.

The information in this user’s guide is subject to change. For the most up-to-date

information on the CSDTF10xx-10x Device, view the user’s guide on-line at:

www.transition.com.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,

Subchapter J applicable at the date of manufacture.

CAUTION: Visible and invisible laser radiation when open. Do not stare into the

beam or view directly with optical instruments.

CAUTION: Use of controls, adjustments or the performance of procedures other than

those specified herein may result in hazardous radiation exposure.

[email protected] -- Click the “Transition Now” link for a live Web chat. 13

Troubleshooting

If the Device fails, isolate and correct the failure by determining the answers to the

following questions and then taking the indicated action:

1. Is the PWR (Power) LED illuminated?

• Is the Device slide-in-module installed properly in the chassis?

• Is the power cord properly installed in the chassis and at the external

power source?

• Does the external power source provide power?

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 2.

2. Is the SDC (Signal Detect / Copper) LED illuminated?

• Check the twisted-pair copper cable for the proper connection.

• Check the MDI/MDI-X switch for the correct twisted-pair copper cable

configuration (see page 3).

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 3.

3. Is the SDF (Signal Detect / Fiber) LED illuminated?

• Check the fiber cables for proper connection.

• Verify that the TX and RX cables on the local Device are connected to the

RX and TX ports, respectively, on the remote Device.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 4.

4. Is data transfer failing?

YES

• Verify the local copper connection by starting a local copper loop-back

(hardware mode: set the loop-back switch on the local Device to “CL”,

software mode: enter the local copper loop-back command) and then use

a bit error test unit to run a bit error test.

• Verify the local fiber connection by starting a remote fiber loop-back

(hardware mode: set the loop-back switch on the remote Device to “FL”,

software mode: enter the remote fiber loop-back command) and then use a

bit error test unit to run a bit error test.

• Verify the remote copper connection by starting a remote copper loop-

back (hardware mode: set the loop-back switch on the remote Device to

“CL”, software mode: enter the remote copper loop-back command) and

then use a bit error test unit to run a bit error test.

• Verify the remote fiber connection by starting a local copper loop-back

(hardware mode: set the loop-back switch on the local Device to “FL”,

software mode: enter the local fiber loop-back command) and then use a

bit error test unit to run a bit error test.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

reppoCrebiFreppoC Local

Device

Remote

Device

Bit Error

Test Unit

Remote

Device

reppoCrebiFreppoC

Bit Error

Test Unit

Local

Device

Remote

Device

Local

Device

reppoCrebiFreppoC

Bit Error

Test Unit

Local

Device

Local

Device

Remote

Device

reppoCrebiFreppoC

Bit Error

Test Unit

Local

Device

Remote

Device

Local

Device

14 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

CSDTF10xx-10x

[email protected] -- Click the “Transition Now” link for a live Web chat. 15

Technical support

Technical support is available 24 hours a day.

U.S.A. and Canada: 1-800-260-1312

International: 00-1-952-941-7600

Transition now

Chat live via the Web with Transition Networks Technical Support.

Log onto www.transition.com and click the Transition Now link.

Web-Based seminars

Transition Networks provides seminars via live web-based training.

Log onto www.transition.com and click the Learning Center link.

E-Mail

Ask a question anytime by sending an e-mail to our technical support staff.

[email protected]

Address

Transition Networks

10900 Red Circle Drive

Minnetonka, MN 55343, U.S.A.

Telephone: 952-941-7600

Toll free: 800-526-9267

Fax: 952-941-2322

Declaration of Conformity

Name of Mfg: Transition Networks

10900 Red Circle Drive, Minnetonka MN 55343 U.S.A.

Model: CSDTF10xx-10x Series Devices

Part Number: CSDTF1011-105, CSDTF1012-105, CSDTF1013-105,

CSDTF1014-105, CSDTF1015-105, CSDTF1016-105,

CSDTF1017-105, CSDTF1018-105, CSDTF1022-105,

CSDTF1025-105, CSDTF1027-105, CSDTF1029-105,

CSDTF1029-106, CSDTF1029-107, CSDTF1029-108

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the CSDTF10xx-10x to which this declaration refers is in

conformity with the following standards.

CISPR 22:1993; EN 55022:1994+A1:1995+A2:1997 Class A; EN 55024:1998; FCC Part 15

Subpart B; EN 61000-3-2:1995+A14:2000; 61000-3-3:1995; CFR 21 subpart J

I, the undersigned, hereby declare that the equipment specified above conforms to the above

Directive(s) and Standard(s).

September, 2008

Stephen Anderson, Vice-President of Engineering Date

Compliance Information

CISPR22/EN55022 Class A + EN55024

CE Mark

FCC regulations

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which

case the user will be required to correct the interference at the user's own expense.

Canadian regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out

on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage

radioélectrique édicté par le ministère des Communications du Canada.

European regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses

Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für Gegenmaßnahmen

verantwortlich.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des

interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures spécifiques

appropriées.

Trademark notice

All trademarks and registered trademarks are the property of their respective owners.

graphic, electronic, or mechanical - without written permission from Transition Networks.

Printed in the U.S.A. 33245.H

CSDTF10xx-10x

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in

damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-

Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der

Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über

Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer

Konformität.

In accordance with European Union Directive 2002/96/EC of the European

Parliament and of the Council of 27 January 2003, Transition Networks will accept

post usage returns of this product for proper disposal. The contact information for this

activity can be found in the 'Contact Us' portion of this document.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Transition Networks Medienkonverter Handbücher

Transition Networks

Transition Networks CFETF10 Series Bedienungsanleitung

Transition Networks

Transition Networks E-100BTX-FX-05 Bedienungsanleitung

Transition Networks

Transition Networks CBFTF1011-155 Bedienungsanleitung

Transition Networks

Transition Networks C/A-CF-02(SM) Bedienungsanleitung

Transition Networks

Transition Networks J-CF-02 Bedienungsanleitung

Transition Networks

Transition Networks CFMFF4040-100 Bedienungsanleitung

Transition Networks

Transition Networks M/GE-xSW-SFP-01-xx-U Series Bedienungsanleitung

Transition Networks

Transition Networks 10BASE-2 Bedienungsanleitung

Transition Networks

Transition Networks E-CX-TBT-03 Bedienungsanleitung

Transition Networks

Transition Networks C/E-100BTX-FX-04(LH) Bedienungsanleitung

Transition Networks

Transition Networks CBFTF10XX-15X Bedienungsanleitung

Transition Networks

Transition Networks E-100BTX-FX-05(LC) Bedienungsanleitung

Transition Networks

Transition Networks MEDIA CONVERTERS E-100BTX-FRL-01 Bedienungsanleitung

Transition Networks

Transition Networks SFMFF1313-220 Bedienungsanleitung

Transition Networks

Transition Networks SRS4F3211-100 Bedienungsanleitung

Transition Networks

Transition Networks F-SM-MM-04(LH) Bedienungsanleitung

Transition Networks

Transition Networks E-100BTX-FRL-03(SC) E-100BTX-FRL-03(SM) Bedienungsanleitung

Transition Networks

Transition Networks CSETF1011-205 Bedienungsanleitung

Transition Networks

Transition Networks CFETF1029-205 Bedienungsanleitung

Transition Networks

Transition Networks SSDTF3011-115 Bedienungsanleitung

Transition Networks

Transition Networks SISTG10 211-LR Series Bedienungsanleitung

Transition Networks

Transition Networks C/HSTR-CF-01(SC) Bedienungsanleitung

Transition Networks

Transition Networks C/E-PSW-SX-01(SC) Bedienungsanleitung

Transition Networks

Transition Networks DataBand EV Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung