Transition Networks SAPTF33xx-100 Bedienungsanleitung

SAPTF33xx-1xx

24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

SAPTF33xx-1xx in the Network

Standard Configuration

One Unit A device (SAPTF33xx-100) and one Unit B device (SAPTF33xx-110)

are required for the standard configuration. The Unit A device is connected to

the Central Office (CO) while the Unit B device is connected to a telephone

device.

Automatic Ring-Down Configuration

Automatic Ring Down (ARD) is a dedicated, point-to-point voice system. When

one telephone is taken off-hook, the other telephone rings, without the need to

dial. Two Unit B devices (SAPTF33xx-110), connected via the fiber ports, are

required for this mode of operation; with a telephone device at each end.

SAPTF33xx-100

Unit A -- Emulates

the telephone device

SAPTF33xx-110

Unit B -- Emulates the

Central Office (CO)

SAPTF33xx-110

Unit B -- Emulates the

Central Office (CO)

SAPTF33xx-110

Unit B -- Emulates the

Central Office (CO)

[email protected] Click the “Transition Now” link for a live Web chat.

Installation

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when setting the jumpers. Failure to observe this caution could

result in damage to, and subsequent failure of, the media converter.

Setting the Jumpers

1. Using a small screwdriver, remove the screws that secure the cover to the

media converter and carefully remove the cover.

2. Locate the jumpers on the circuit board.

3. Using small needle-nosed pliers or similar device, move the jumper to the

desired position. (Refer to the drawings below.)

4. Carefully replace the cover on the media converter and replace the

screws to secure the cover.

Standard / Automatic Ring-Down

The jumper labeled “JP1” is used to switch between the Standard or Automatic

Ring-Down configuration and is located on the top circuit board of Unit B

(SAPTF33xx-110).

The drawing below illustrates the jumper settings.

• Set jumper JP1 on the Unit B device to the Standard setting when

using the Standard configuration (described on page 4).

• Set jumper JP1 on both Unit B devices to the Automatic Ring-Down

setting when using the Automatic Ring-Down configuration

(described on page 4).

US / EU Telephone Regulation

The jumper labeled “US EU” is used to switch between the US or EU

telephone configuration and is located on the top circuit board of Unit A

(SAPTF33xx-100). This feature is required to comply with the EU TBR21

telephone regulation. The jumper has been set at the factory to the US setting

as the default.

The drawing below illustrates the jumper settings.

• Set jumper “US EU” on the Unit A device to the US setting if the

device is to be used with US-based telephone systems.

• Set jumper “US EU” on the Unit A device to the EU setting if the

device is to be used with European-based telephone systems.

Standard 13

Automatic

Ring-Down 1

JP1 JP1

US Setting EU Setting

US EU US EU

Installation -- Continued

Grounding the Media Converter

The SAPTF33xx-1xx single-slot chassis comes equipped with grounding lugs

located on the back panel. They require a grounding conductor wire

terminated with a two-hole, compression-type, grounding connector. The

grounding wire -- which must be a copper conductor -- is not included with

the chassis and must be provided by the customer/installer.

The electrical conducting path from the single-slot chassis must:

• Flow via the grounding lugs to the common bonding network (CBN).

• Be of sufficiently low impedance to conduct fault currents likely to be

imposed on the media converter, and

• Enable proper operation of any over-current protection devices.

The conductor must be fastened to the grounding lugs with the enclosed anti-

rotation star-washers and lug-nut fasteners. The applied torque required to the

connector lug-nut fasteners is specified by the connector’s manufacturer.

To properly ground the SAPTF33xx-1xx single-slot chassis:

1. Obtain one (1) grounding conductor (12 AWG copper wire gauge or

larger) with a two-hole, compression-type, grounding connector.

2. Attach the grounding conductor to the converter by placing the two-hole

connector onto the grounding lugs and fasten with the enclosed lock-

washers / lug-nuts at the proper torque (per the manufacturer’s

specification).

3. Attach the opposite end of the

grounding conductor to the

common bonding network

(CBN).

rounding lugs

earth ground

grounding

connector

and wire

SAPTF33xx-1xx

24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

3/4-inch

spacin

Grounding lugs

(6-32, 1/8" diam.) 12 AWG copper wir

(not included)

Star washer (included)

Lug nuts (included)

Two-hole, compression-type

grounding connector

(not included)

[email protected] Click the “Transition Now” link for a live Web chat.

Installation -- Continued

Installing the Cable -- Standard Configuration

NOTE: Unit B MUST be configured for Standard Configuration (see page 4).

Fiber

1. Locate or build fiber cable with male, two-stranded TX to RX connectors

installed at both ends.

2. Connect the fiber cables to Unit A (SAPTF33xx-100) as described:

• Connect the male TX cable connector to the female TX port.

• Connect the male RX cable connector to the female RX port.

3. Connect the fiber cables to Unit B (SAPTF33xx-110) as described:

• Connect the male TX cable connector to the female RX port.

• Connect the male RX cable connector to the female TX port.

Copper

1. Locate or build copper cables with male, RJ-

11C connectors installed at both ends.

2. Connect the copper cables to Unit A

(SAPTF33xx-100) as described:

• Connect the RJ-11C connector at one

end of the cable to the RJ-11C port on

Unit A.

• Connect the RJ-11C connector at the

other end of the cable to the RJ-11C port

on the Central Office.

3. Connect the copper cables to Unit B

(SAPTF33xx-110) as described:

• Connect the RJ-11C connector at one

end of the cable to the RJ-11C port on

Unit B.

• Connect the RJ-11C connector at the

other end of the cable to the RJ-11C port

on the telephone device.

TX RX

ACT

SDF

PWR

TX RX

ACT

SDF

PWR

Connect to the

RJ-11C port on the

Central Office.

Connect to the

RJ-11C port on the

telephone device.

Unit A

Unit B

Unit A Unit B

SAPTF33xx-1xx

24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Installation -- Continued

Installing the Cable -- Automatic Ring-Down Configuration

NOTE: Both Unit B’s MUST be configured for Automatic Ring-Down (see page 4).

Fiber

1. Locate or build fiber cable with male, two-stranded TX to RX connectors

installed at both ends.

2. Connect the fiber cables to the first Unit B (SAPTF33xx-110) as described:

• Connect the male TX cable connector to the female TX port.

• Connect the male RX cable connector to the female RX port.

3. Connect the fiber cables to the second Unit B (SAPTF33xx-110) as

described:

• Connect the male TX cable connector to the female RX port.

• Connect the male RX cable connector to the female TX port.

Copper

1. Locate or build copper cables with male, RJ-11C connectors installed at

both ends.

2. Connect the copper cables to both Unit B’s (SAPTF33xx-110) as described:

• Connect the RJ-11C connector at one end

of the cable to the RJ-11C port on the

first Unit B.

• Connect the RJ-11C connector at the

other end of the cable to the RJ-11C port

on the telephone device.

3. Connect the copper cables to the second Unit

B(SAPTF33xx-110) as described in step 2.

TX RX

ACT

SDF

PWR

TX RX

ACT

SDF

PWR

Connect to the

RJ-11C port on the

telephone device.

Unit B

Unit B Unit B

[email protected] Click the “Transition Now” link for a live Web chat.

Operation

Power the Media Converter

NOTE: The external power supply provided with this product is UL listed by

the power supply’s manufacturer.

1. Install the barrel connector of the AC power cord to the external power

connector on back of the media converter.

2. Connect the AC power cord to the correct voltage AC rack or wall socket.

3. Verify that the media converter is powered by observing the illuminated

LED power indicator light.

Consult the user’s guide for the Transition Networks SPS1872-xx DC external

power supply for powering the media converter.

Status LEDs

Use the status LEDs to monitor the SAPTF33xx-1xx media converter operation

in the network.

PWR (Power)

On = The media converter is connected to external power.

SDF (Signal Detect Fiber Link)

On = The fiber link is active.

ACT (Activity)

On = The telephone device is in use (off-hook).

Flashing = The telephone device is ringing or pulse-dialing.

ACT

SDF

PWR

SAPTF33xx-1xx

24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Operation - Continued

Loop-Start Operation

Loop-Start Service -- commonly known as “Plain Old Telephone Service”

(POTS) -- is the primary analog signaling method used between telephone

switches such as the Central Office (CO) and a telephone device. Loop-Start

provides a way to indicate on-hook and off-hook conditions, which facilitates

outgoing and incoming calls in a voice network.

When a customer wants to make an outgoing call, he or she takes a telephone

device off-hook. This action completes the loop, which signals the CO that a

customer desires to use the telephone line. To signal the customer of an

incoming call, the CO applies a ring voltage to alert the customer.

The three states of the Loop-Start signaling protocol are described below:

Idle State (On-Hook)

1. The CO applies a battery voltage to the ring lead and monitors the

tip-ring current for closure of the tip-ring.

2. The telephone device draws less than 10 µA of from the line while

waiting for the superimposition of the ringing voltage over the ring

lead.

Telephone In-Use (Off-Hook)

1. The customer takes the telephone device off-hook, drawing a

minimum of 20 to 30 mA of current.

2. The CO senses the tip-ring current and issues a dial tone on the line.

3. Communication can now begin.

Central Office (CO) Rings the Telephone

1. The CO superimposes the ringing voltage over the ring lead battery.

2. The telephone device uses the ring voltage to operate the ringer,

which alerts the customer of an incoming telephone call.

3. The customer takes the phone off-hook, which closes the tip-ring

connection and allows the tip-ring current to flow.

4. The CO senses the DC current from the telephone device and

connects the call to the telephone line.

5. Communication can now begin.

[email protected] Click the “Transition Now” link for a live Web chat.

Cable Specifications

The physical characteristics must meet or exceed FCC part 68 specifications.

Copper Cable -- Category 1

Either shielded (STP) or unshielded (UTP) twisted-pair is acceptable.

Gauge: 24 to 22 AWG

Maximum # Nodes: 2

Maximum Cable Length: 5 meters (16.4 ft) (Unit A and CO)

5 km (3.1 mi) (Unit B and telephone)

Fiber Cable

Bit error rate: ≤10-9

Single mode fiber (recommended): 9 µm

Multimode fiber (recommended): 62.5/125 µm

Multimode fiber (optional): 100/140, 85/140, 50/125 µm

SAPTF3311-100, SAPTF3311-110 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

SAPTF3313-100, SAPTF3313-110 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

SAPTF3314-100, SAPTF3314-110 1310 nm single mode

Fiber Optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm

Fiber Optic Receiver Sensitivity: min: -31.0 dBm max: -8.0 dBm

Link Budget: 16.0 dB

SAPTF3315-100 1310 nm single mode

Fiber Optic Transmitter Power: min: -27.0 dBm max: -10.0 dBm

Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -14.0 dBm

Link Budget: 13.0 dB

SAPTF3315-110 1310 nm single mode

Fiber Optic Transmitter Power: min: -8.0 dBm max: -2.0 dBm

Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 26.0 dB

SAPTF3329-100, SAPTF3329-110

SAPTF3329-101, SAPTF3329-111 1310 nm single mode

Fiber Optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm

Fiber Optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

SAPTF3329-102, SAPTF3329-112

SAPTF3329-103, SAPTF3329-113 1310 nm single mode

Fiber Optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm

Fiber Optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm

Link Budget: 25.0 dB

The fiber optic transmitters on this device meets Class I Laser safety requirements

per IEC-825/CDRH standards and complies with 21 CFR1040.10 and

21CFR1040.11.

Technical Specification

For use with Transition Networks Model SAPTF33xx-1xx or equivalent

Standards FCC Part 68, TBR21

Dimensions 3.6" x 4.5" x 1.8" (91 mm x 115 mm x 45 mm)

Shipping Weight 1 lb. (0.45 kg) (approximate)

Power Consumption 7.0 watts

Power Supply 12VDC, 0.8 Amp (North America, Europe, UK)

12VDC, 1.25 Amp (Latin Am., Japan, N.Z., Australia, S. Africa)

The external power supply provided with this product is UL

listed by the power supply’s manufacturer.

MTBF 47,000 hours (MIL217F2 V5.0) (MIL-HDBK-217F)

115,000 hours (Bellcore7 V5.0)

Environment Tmra*: 0° to 50°C (32° to 122° F )

Storage Temp: -15° to 65°C (-4° to 122°F)

Humidity: 5 to 95%, non condensing

Altitude: 0 to 10,000 feet

Warranty Lifetime

*Manufacturer’s rated ambient temperature.

The information in this user’s guide is subject to change. For the most up-to-date

information on the SAPTF33xx-1xx media converter, view the user’s guide on-line at:

www.transition.com.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR, Subchapter J

applicable at the date of manufacture.

CAUTION: Visible and Invisible Laser Radiation When Open. Do Not Stare Into Beam Or

View Directly With Optical Instruments.

CAUTION: Use of controls, adjustments or the performance of procedures other than

those specified herein may result in hazardous radiation exposure.

SAPTF33xx-1xx

24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

RJ-11C Connector Specification

Unit A (Telephone Emulation)

Connector: RJ-11C

Impedance: 600 Ω

REN: 0.4 B

Loop Current: 10 to 100 mA

Insertion Loss: 0.0 ± 1.0 dB at 1000 Hz

(When both ports are terminated at 600 Ω.)

Unit B (Central Office Emulation)

Connector: RJ-11C

Impedance: 600 Ω

Battery Source: 48 VDC +/- 5V

Ringing Supply: 90 Vp-p

RIng Frequency: 15-30 Hz (Reproduces the frequency detected by Unit A.)

Ring Cadence: Reproduces the cadence detected by Unit A.

Insertion Loss: 0.0 ± 1.0 dB at 1000 Hz

(When both ports are terminated at 600 Ω.)

[email protected] Click the “Transition Now” link for a live Web chat.

Troubleshooting

1. Is the PWR (power) LED illuminated?

• Is the power adapter the proper type of voltage and cycle frequency

for the AC outlet? (See “Power Supply” on page 12.)

• Is the power adapter properly installed in the media converter and in

the outlet?

• Does the external power source provide power?

• Contact Technical Support: US/Canada: 1-800-260-1312,

International: 00-1-952-941-7600.

YES

• Proceed to step 2.

2. Is the SDF (signal detect fiber Link) LED illuminated?

• Check the fiber cables for proper connection.

• Verify that the TX and RX cables on the first media converter are

connected to the RX and TX ports, respectively, on the second media

converter.

• Contact Technical Support: US/Canada: 1-800-260-1312,

International: 00-1-952-941-7600.

•

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Transition Networks Medienkonverter Handbücher

Transition Networks

Transition Networks SSETF10XX-200 Bedienungsanleitung

Transition Networks

Transition Networks FBRM1XXX-1XX Bedienungsanleitung

Transition Networks

Transition Networks M/E-PSW-FX-02 Bedienungsanleitung

Transition Networks

Transition Networks C/E-TX-SX-02 Bedienungsanleitung

Transition Networks

Transition Networks SBFTF1011-110 Bedienungsanleitung

Transition Networks

Transition Networks ARCNET AR-CF-02 Bedienungsanleitung

Transition Networks

Transition Networks C/RS485-CF-01(SC) Bedienungsanleitung

Transition Networks

Transition Networks SSDTF3011-115 Bedienungsanleitung

Transition Networks

Transition Networks J/E-PSW-FX-02(SC) Bedienungsanleitung

Transition Networks

Transition Networks ARCNET C/AR-CF-02(SC) Bedienungsanleitung

Transition Networks

Transition Networks ARCNET C/AR-CF-01(SC) Bedienungsanleitung

Transition Networks

Transition Networks M/GE-PSW-SX-01 Bedienungsanleitung

Transition Networks

Transition Networks M/GE-PSW-LX-01 Bedienungsanleitung

Transition Networks

Transition Networks C4TEF10XX-10X Bedienungsanleitung

Transition Networks

Transition Networks SGPOE10 1 Series Bedienungsanleitung

Transition Networks

Transition Networks C/E-PSW-FX-03(LH) Bedienungsanleitung

Transition Networks

Transition Networks CBFTF10xx-1xx Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-FRL-03(L) Bedienungsanleitung

Transition Networks

Transition Networks SPS-1872-CC Bedienungsanleitung

Transition Networks

Transition Networks M/GE-PSW-SFP-01 Bedienungsanleitung

Transition Networks

Transition Networks SISTG10 211-LR Series Bedienungsanleitung

Transition Networks

Transition Networks CFETF1011-110 Bedienungsanleitung

Transition Networks

Transition Networks C/E-100BTX-FRL-03 Bedienungsanleitung

Transition Networks

Transition Networks M/GE-SW-SFP-01-U Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung