Transition Networks LANart EFA0201 Bedienungsanleitung

Ethernet™10Mbps/100Mbps

PCI Network Interface Cards

EFA0201, EFA0202, EFA0203

USER’S GUIDE

Installation Notes.......................................................................2

EFA020x PCI Cards....................................................................3

Microsoft Windows 95 - New Installation ................................4

Microsoft Windows 98 - New Installation ................................5

Microsoft Windows NT 4.0 - New Installation..........................6

Novell Netware 4.X - New Installation.....................................7

Microsoft Windows 95 - Software Upgrade.............................8

Microsoft Windows 98 - Software Upgrade.............................8

Microsoft Windows NT 4.0 - Software Upgrade......................9

Novell Netware 4.X - Software Upgrade/Adding Network Card to

Existing system...............................................................10

Microsoft Windows NT 4.0 - Permanet Server.........................11

Compliance Information..........................................................12

INSTALLATION NOTES

Adapter Hardware Installation

Follow Instructions outlined in the indicated personal computer user’s guide for installing PCI Bus add-in cards

into a PCI slot that supports bus mastering.

CAUTION: Heed the warnings in the PC User's Manual in regard to proper protection against static discharge.

Always hold the adapter by the metal bracket. Always be properly grounded when handling an adapter. Since

LANart adapters are designed with CMOS ICs and are particularly sensitive to static discharge, failure to observe

this caution could result in damage to the adapter and subsequent failure.

Once the adapter is installed in the PC, power the PC.

Adapter Software Installation

LANart EFA020x series PCI Fiber-Optic Adapters are shipped with three (3) driver disks, which contain software

drivers for various network operating systems, diagnostic utilities, and electronic format documentation.

Follow the directions in this user’s guide (also provided on Disk 3) to install the indicated software driver.

Technical Support

EFA020x PCI CARDS

LANart EFA020x series PCI Fiber-Optic Adapters, EFA0201. EFA0202, and EFA0203, are 32-bit bus-mastering PCI

cards that support both half-duplex and full-duplex operation.

LANart EFA020x adapters comply with PCI Specifications, revision 2.1, and with both IEEE 802.3 10BASE-FL and

802.3u 100BASE-FX standards

EFA0201 Provides one (1) connection to 10BASE-FL fiber cable.

EFA0202 Provides one (1) connection to 100BASE-FX fiber

cable.

EFA0203 Provides one (1) connection to 10BASE-FL fiber cable

AND one (1) connection to 100BASE-FX fiber cable.

NOTE: Only one EFA0203 connection, 100BASE-FX

OR 10BASE-FL, is operational at any one time. Moving

cable between the 10BASE-FL connection and the

100BASE-FX connection selects a change in speed. If

cable is inatalled at BOTH connections on the

EFA0203, then, as long as the Fast Ethernet link is

available, the LANart NIC operates at 100Mbps and

the 10BASE-FL link is inactive. Should the 100Mbps

network become unavailable - due to a fault at any

point on the network - the LANart NIC seamlessly

switches activity to the 10BASE-FL port and continu-

ously monitors the 100BASE-FX network for a restored

link. When the Fast Ethernet link is restored, the

LANart NIC seamlessly switches activity back to the

100BASE-FX port.

LED INDICATORS

The two LEDs closest to each connector shows link status and activity for that port. Collision, full-duplex, and

10Mbps/100Mbps selection LEDs apply to the active network port.

LNK (L(i)nk integrity) Steady green LED indicates link is able to pass data.

Dark LED indicates link is unavailable. To correct, verify that the RX port is cabled to

the TX port at the far end of the cable, and vice versa. Also verify that the equipment is

functioning at the far end and that the cabling does not exceed IEEE 802.3(u) recom-

mended lengths.

ACT (Act(ivity)) Flashing yellow LED indicates link is passing traffic

Dark LED indicates link is idle. NOTE: If link is unavailable, indicator is dark.

FD (F(ull) D(uplex)) Steady green LED indicates full duplex mode.

Dark LED indicates half duplex mode.

COL (COL(lisiion)) Flashing yellow LED indicates network activity.

100 (Port selectiion) Steady green LED indicates that EFA0203 100BASE-FX port has been

(automatically) selected as the active link.

Dark LED indicates that EFA0203 10BASE-FL port has been (automatically) selected as

the active link.

MICROSOFT WINDOWS 95 - NEW INSTALLATION

1. Copy the appropriate device install script

For NDIS3 MAC driver type

copy A:\Win95\Nids3\Mac\Netamd.inf C:\Windows\Inf

For NDIS4 MINIPORT driver type

copy A:\Win95\Nids4\Mini\Netamd.inf C:\Windows\Inf

2. Shutdown Windows 95 and power-off the machine.

3. Install the LANart EFA020X Adapter card in accordance with your personal computer user's manu-

al. Again, follow all handling procedures to avoid electro-static discharges.

4. Turn the computer on to start Windows 95

5. If your computer is Plug and Play compatible, Windows 95 will recognize that new hardware has

been installed, and will attempt to configure itself. Follow the steps below. Other wise, Skip to

step 12

6. Insert the LANart Driver Disk 1 into the floppy disk drive. When prompted for the LANart Win 95

Disk

7. Type the following path

For NDIS3 MAC driver type -

A:\Win95\Nids3\Mac

For NDIS4 MINIPORT driver type -

A:\Win95\Nids4\Mini

9. When prompted insert the Windows 95 CD-ROM

10. Click "Yes"

11. Remove the LANart driver disk, and power up the computer, and start Windows 95. When system

comes up go to step 19

12. If your computer is not Plug and Play compatible, open the control panel by clicking "Start," then

"Settings," then "Control Panel."

13. Open the Network control panel by double clicking the "Network" icon.

14. Click "Add" inside the Network control panel, then select "Adapter", and click "Add" inside the

Select Network Component Type window. Select "Have Disk."

15 For the NDIS3 MAC driver, type at the prompt:

"A:\Win95\Ndis3\Mac"

and click "OK."

For the NDIS4 MINIPORT driver, type at the prompt:

"A:\Win95\Ndis4\Mini"

and click "OK."

16. Select "OK" to exit the Network control panel.

17. You will be prompted to insert your original Windows 95 CD. Insert the CD, and click "OK" to

begin copying files.

18. Restart the computer to and follow steps below.

19. When the system comes up open the control panel by clicking "Start," then "Settings," then

"Control Panel."

20. Double Click "system"

21. Click "Device Manager"

22. Double Click "Network Adapter"

23. Highlight "LANart …." And , Click on "Properties"

24. Click on Advance

25. Chose the properties as required by Network Administrator

26. Restart the computer. Your LANart adapter is now configured. To access your network, protocols

will need to be configured. Please see your network administrator for details.

MICROSOFT WINDOWS 98 - NEW INSTALLATION

1. Copy the appropriate device install script

For NDIS3 MAC driver type

copy A:\Win98\Nids3\Mac\Netamd.inf C:\Windows\Inf

For NDIS4 MINIPORT driver type

copy A:\Win98\Nids4\Mini\Netamd.inf C:\Windows\Inf

2. Shutdown Windows 98 and power-off the machine.

3. Install the LANart EFA020X Adapter card in accordance with your personal computer user's manu-

al. Again, follow all handling procedures to avoid electro-static discharges.

4. Turn the computer on to start Windows 98

5. If your computer is Plug and Play compatible, Windows 98 will recognize that new hardware has

been installed, and will attempt to configure itself. Follow the steps below. Other wise, Skip to

step 12

6. Insert the LANart Driver Disk 1 into the floppy disk drive. When prompted for the LANart Win 98

Disk

7. Type the following path

8. For NDIS3 MAC driver type -

A:\Win98\Nids3\Mac

For NDIS4 MINIPORT driver type -

A:\Win98\Nids4\Mini

9. When prompted insert the Windows 98 CD-ROM

10. Click "Yes"

11. Remove the LANart driver disk, and power up the computer, and start Windows 98. When system

comes up go to step 19

12. If your computer is not Plug and Play compatible, open the control panel by clicking "Start," then

"Settings," then "Control Panel."

13. Open the Network control panel by double clicking the "Network" icon.

14. Click "Add" inside the Network control panel, then select "Adapter", and click "Add" inside the

Select Network Component Type window. Select "Have Disk."

15. For the NDIS3 MAC driver, type at the prompt:

"A:\Win95\Ndis3\Mac" and click "OK."

For the NDIS4 MINIPORT driver, type at the prompt:

"A:\Win95\Ndis4\Mini" and click "OK."

16. Select "OK" to exit the Network control panel.

17. You will be prompted to insert your original Windows 95 CD. Insert the CD, and click "OK" to

begin copying files.

18. Restart the computer to and follow steps below.

19. When the system comes up open the control panel by clicking "Start," then "Settings," then

"Control Panel."

20. Double Click "system"

21. Click "Device Manager"

22. Double Click "Network Adapter"

23. Highlight "LANart …." And , Click on "Properties"

24. Click on Advance

25. Chose the properties as required by the Network Administrator

26. Restart the computer. Your LANart adapter is now configured. To access your network, protocols

may need to be configured. Please see your network administrator for details.

3.5. MICROSOFT WINDOWS NT 4.0 - NEW INSTALLATION

1. Install the LANart EFA020X Adapter card in accordance with your personal computer user's manu-

al. Again, follow all handling procedures to avoid electro-static discharges.

2. Start Windows NT, and open the control panel by clicking "Start," then "Settings," then "Control

Panel."

3. Double Click on "Network."

4. Click on the Adapters tab.

5. Click "Add" inside the Network control panel, then select "Adapter."

6. Select "Have Disk."

7. Insert the LANart Driver Disk 2 into the floppy drive

8. For the NDIS3 MAC driver, type at the prompt:

"A:\Winnt\Ndis3\Mac" and click "OK."

For the NDIS4 MINIPORT driver, type at the prompt:

"A:\Winnt\Ndis3\Mini" and click "OK."

9. Choose the appropriate LANart EFA020X Adapter and Click on "OK"

10. Click on "Properties" - Choose the appropriate properties as required by the Network Administrator

for the driver to work properly.

Click "Close" - Protocols may be needed to be configured. Please see your Network

Administrator for details

11. Select "OK" to exit the Network control panel, and Select "OK" when prompted to restart your

machine. Remove the LANart Driver Disk.

12. If this is your first adapter installation, you will be prompted to insert your original Windows NT

CD. Insert the CD, and click "OK" to begin copying files.

13. Restart the computer. Your LANart adapter is now configured. To access your network, protocols

may need to be configured. Please see your network administrator for details.

NOVELL NETWARE 4.X - NEW INSTALLATION

1. Power off the machine.

2. Install the LANart EFA020X Adapter card in accordance with your personal computer user's man-

ual. Again, follow all handling procedures to avoid electro-static discharges.

3. Install the server software

4. When the NIC selection menu appears, place the appropriate diskette (Disk 3)into the floppy drive

5. Press Insert (Ins)

6. Press [F3] to change the path.

7. At the A: prompt, type

\Novell\Nwsrvr41

MICROSOFT WINDOWS 95 - SOFTWARE UPGRADE

1. Power up the computer, and start Windows 95.

2. The following instruction is to update the driver for LANart network card.

3. Update the driver for LANart EFA020X - open the control panel by clicking "Start," then "Settings,"

then "Control Panel."

4. Double Click "system"

5. Click "Device Manager"

6. Double Click "Network Adapter"

7. Highlight "LANart…." And , Click on "Properties"

8. Click on "Driver" and Click on "Update Driver"

9. Click on "Next" and choose - "No, Select Driver from List."

10. Click "Next" and Highlight LANart EFA020X Adapter

11. Click "Have Disk"

12. For the NDIS3 MAC driver, type at the prompt:

"A:\Win95\Ndis3\Mac" and click "OK."

For the NDIS4 MINIPORT driver, type at the prompt:

"A:\Win95\Ndis4\Mini" and click "OK."

13. Click "OK"

14. Click "Next" and Click "Finish"

15. Click "Yes" to restart the computer. And, when the system comes up open the control panel by

clicking "Start," then "Settings," then "Control Panel."

16. Double Click "system"

17. Click "Device Manager"

18. Double Click "Network Adapter"

19. Highlight "LANart …." And , Click on "Properties"

20. Click on Advance

21. Chose the properties as required by the Network Administrator

22. Restart the computer. Your LANart adapter is now configured. To access your network, protocols

will need to be configured. Please see your network administrator for details.

MICROSOFT WINDOWS 98 - SOFTWARE UPGRADE

1. Power up the computer, and start Windows 98.

2. The following instruction is to update the driver for LANart network card.

3. Update the driver for LANart EFA020X - open the control panel by clicking "Start," then "Settings,"

then "Control Panel."

4. Double Click "system"

5. Click "Device Manager"

6. Double Click "Network Adapter"

7. Highlight "LANart…." And , Click on "Properties"

8. Click on "Driver" and Click on "Update Driver"

9. Click on "Next" and choose - "No, Select Driver from List."

10. Click "Next" and Highlight LANart EFA020X Adapter

11. Click "Have Disk"

12. For the NDIS3 MAC driver, type at the prompt:

"A:\Win98\Ndis3\Mac" and click "OK."

For the NDIS4 MINIPORT driver, type at the prompt:

"A:\Win98\Ndis4\Mini" and click "OK."

13. Click "OK"

14. Click "Next" and Click "Finish"

15. Click "Yes" to restart the computer. And, when the system comes up open the control panel by

clicking "Start," then "Settings," then "Control Panel."

16. Double Click "system"

17. Click "Device Manager"

18. Double Click "Network Adapter"

19. Highlight "LANart …." And , Click on "Properties"

20. Click on Advance

21. Chose the properties as required by the Network Administrator

22. Restart the computer. Your LANart adapter is now configured. To access your network, protocols

will need to be configured. Please see your network administrator for details.

MICROSOFT WINDOWS NT 4.0 - SOFTWARE UPGRADE

1. Start Windows NT, and open the control panel by clicking "Start," then "Settings,"

then "Control Panel."

2. Double Click on "Network."

3. Click on the Adapters tab.

4. Highlight the existing LANart adapter, and click "Remove." Close the control panel to effect the

change.

5. Re-open the Network control panel, and click "Add," then select "Adapters."

6. Select "Have Disk."

7. Insert the LANart Driver Disk 2 into the floppy drive

8. For the NDIS3 MAC driver, type at the prompt:

"A:\Winnt\Ndis3\Mac" and click "OK."

For the NDIS4 MINIPORT driver, type at the prompt:

"A:\Winnt\Ndis3\Mini" and click "OK."

9. Choose the appropriate LANart EFA020X Adapter and Click on "OK"

10. Click on "Properties" - Choose the appropriate properties as required by Network Administrator

for the driver to work properly.

11. Select "OK" to exit the Network control panel, and Select "OK" when prompted to restart your

machine. Remove the LANart Driver Disk.

12. If this is your first adapter installation, you will be prompted to insert your original Windows NT

CD. Insert the CD, and click "OK" to begin copying files.

Click "Close"

13. Protocols may be needed to be configured. Please see your Network Administrator for details.

14. Restart the computer to begin using your LANart adapter.

NOVELL NETWARE 4.X - SOFTWARE UPGRADE/ADDING NETWORK

CARD TO EXISTING SYSTEM.

1. Shutdown Netware Server and power-off the machine.

2. Install the LANart EFA020X Adapter card in accordance with your personal computer user's man-

ual. Again, follow all handling procedures to avoid electro-static discharges.

3. On the server’s prompt type: LOAD INSTALL

4. Choose - "Driver Option"

5. Select - Configure Network driver"

6. Select "Load a Driver"

7. Press Insert (Ins)

8. Press <F3>

9. Insert LANart Disk 3 in the floppy drive

10. Type at the A prompt - \Novell\nwsrvr41

11. Choose the appropriate LANart EFA020X driver and proceed to configure the adapter

12. Save and Load the driver

13. See your Network Administrator for the proper network numbers and continue with the installa-

tion.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Transition Networks Netzwerkkarte Handbücher

Transition Networks

Transition Networks N-GXE-POE-x-01 Series Bedienungsanleitung

Transition Networks

Transition Networks NDM-FTX-XX-01 Bedienungsanleitung

Transition Networks

Transition Networks N-FX-MT-01 Bedienungsanleitung

Transition Networks

Transition Networks N-FXE-xxx-01 Bedienungsanleitung

Transition Networks

Transition Networks N-FX-XX-02 Bedienungsanleitung

Transition Networks

Transition Networks N-FX-xxxx-02 Bedienungsanleitung

Transition Networks

Transition Networks NM2-FXS-2230-SFP-01 Bedienungsanleitung

Transition Networks

Transition Networks M2-FXS-2230-SFP-01 Bedienungsanleitung

Transition Networks

Transition Networks N-FX-xx-03 Bedienungsanleitung

Transition Networks

Transition Networks NM2-GXE-2230-01 Series Bedienungsanleitung

Transition Networks

Transition Networks N-GXX-XX-01 Bedienungsanleitung

Transition Networks

Transition Networks N-GXE Series Bedienungsanleitung

Beliebte Netzwerkkarte Handbücher anderer Marken

FirstComm

FirstComm OBiWiFi5G Bedienungsanleitung

Sun Microsystems

Sun Microsystems Interface Adapter Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3 Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Belkin

Belkin F5D7050 Bedienungsanleitung

3Com

3Com EtherLink 3C509B Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITX Bedienungsanleitung

Cisco

Cisco MC16E Bedienungsanleitung

Delta Electronics

Delta Electronics Braking Modules VFDB Series Bedienungsanleitung

TwinMOS

TwinMOS Booming Bedienungsanleitung

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Bedienungsanleitung

Buffalo

Buffalo AirStation WLI-PCM-L11GP Bedienungsanleitung

National Instruments

National Instruments NI 9234 Bedienungsanleitung

Bose

Bose PowerMatch Dante Bedienungsanleitung

Compaq

Compaq Wireless LAN 100 Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITXR Bedienungsanleitung

Gigafast

Gigafast EE101-AEX Bedienungsanleitung