Transition Networks SM24TBT2DPA Bedienungsanleitung
Transition Networks SM24TBT2DPA Quick Start Guide
33736 Rev. D https://www.transition.com Page 1of 2
SM24TBT2DPA
Managed Switch, 24-port Gigabit PoE++, 2-port
SFP/RJ-45 Combo
Quick Start Guide
Transition Networks’ SM24TBT2DPA Switch is a next-generation Ethernet switch offering full L2 features, full PoE
functionality, PoE++ per port output up to 90W. The
Non-Stop PoE
feature lets you upgrade switch firmware or
reboot while retaining PoE power to PDs. Note: see the Install Guide for important Safety Warnings and Cautions,
specifications, features, mounting, connections, grounding, powering, configuration, troubleshooting, regulatory,
service, warranty and tech support Information.
LED Descriptions: The front panel LEDs provide switch status checking and monitoring.
SYS (System) LED: indicates if the switch is powered up correctly or if there is a system alarm triggered.
Mode LEDs: indicate the mode of all RJ45/SFP ports on the switch. You can press the Mode/Reset button
sequentially to switch between the two different modes (Link/Activity/Speed mode and PoE mode).
Port Status LEDs: indicate the current status of each RJ45/SFP port. You can check these LEDs for port status in
different modes after changing the mode by pressing the Mode/Reset button.
Press the Mode/Reset button for less than 2 seconds to change LED mode (Link/Act/Speed Mode or PoE Mode);
you can then check the port status by reading the LED behaviors per the Install Guide.
Mode/Reset Button: Press the front panel Mode/Reset Button for a period of time to:
Change LED Mode: Press the button for 0 ~ 2 seconds; the SYS LED is ON Green; the Port Status
LED status changes based on the mode selected.
Reset the Switch: Press the button for 2 ~ 7 seconds; the SYS LED blinks Green; all port Status LEDs
are Off.
Restore to Defaults: Press the button for 7 ~ 12 seconds; the SYS LED blinks Green; all port Status LEDs are On.
Back Panel: The back panel provides for dual hot-swappable 1560W power supplies for powering the switch.
The switch ships with one power supply (780 Watts) standard; use a secondary power supply module (1560
Watts) if the full 90 Watts output is needed on all ports.
Package Contents: Check the package contents to make sure you have received the one Switch with a Power
Supply installed, one AC Power cord, a second Power Supply (Optional), one RJ-45 to DB-9 cable, and four rubber
feet.
Install SFP Modules: Do not look into laser ports. 1. Position the SFP at either install slot with
the SFP label facing correctly. 2. Carefully slide the SFP device into the slot, aligning it with the
internal installation guides. 3. Press firmly so the SFP firmly seats against the internal mating
connector. 4. Attach an appropriate cable into the SFP module port. 5. Attach the other end of
the cable into the other device.
Grounding: ATTENTION: This case must be grounded. No DC input may be earth grounded. Use
Isolated Power Supply. Note: The switch is an indoor device. If it used with outdoor devices such
as outdoor IP cameras or outdoor WAPs, then you should install a surge protector or surge
suppressor in order to protect the switch.
Transition Networks SM24TBT2DPA Quick Start Guide
33736 Rev. D https://www.transition.com Page 2of 2
Connecting to Power: CAUTION! Hazardous Area: Do Not remove this cover. Trained service people only. No
serviceable components inside. CAUTION: Hot Surfaces. WARNING: For continued protection against risk of fire,
replace only with same type and rating of fuse. Note the sticker indicating “To Keep Warranty Please Do NOT
Remove”. Warning: Class I Equipment. This equipment must be earthed. The power plug must be connected to a
properly wired earth ground socket outlet. An improperly wired socket outlet could place hazardous voltages on
accessible metal parts. Warning: shock hazards exist that can result in serious injury or death if safety instructions
are not followed. Note: This product is to be connected only to UL listed PoE networks and without routing to the
outside plant. Power Connection Warning:Connect the power supply to the switch first, and then connect the
power supply to power. Otherwise catastrophic product failure may occur. 1. Verify that power is off to the DC
circuit that you are going to attach to the switch PoE DC-input connector. This can be either of the two power
supplies (AC-input or DC-input) or site source DC. 2. As an added precaution, place an appropriate safety flag and
lockout device at the source power circuit breaker, or place a piece of adhesive tape over the circuit breaker
handle to prevent accidental power restoration while you are working on the circuit. Power Disconnection: To
disconnect power from the switch after a successful boot: 1. Turn off power to the switch. 2. Disconnect the
cables.
Connect the AC Power Cord: Warning: Risk of electrical shock.
Warning: Shock/damage hazard exists if power supply is installed / removed while
powered on. 1. Refer to the “Grounding” section above. 2. Remove the blank faceplate
or use the one open power supply slot. 3. Fasten the AC Power Supply with the slotted
retaining screw. 4. Insert the provided AC Power plug into the switch AC receptacle
(power inlet). 5. Connect the other end of the AC power cord to the AC power outlet. 6.
Check that the AC OK and DC OK LEDs are lit.
Initial Switch Config via Web Browser: 1. Connect the PC Ethernet RJ45 connector to the switch via standard
Ethernet LAN cable. 2. Power up the PC to be used for initial config. 3. Reconfigure the PC’s IP address and Subnet
Mask so it can communicate with the switch. 4. Power up the switch to be initially configured and wait until it has
finished its start-up processes. 5. Connect the PC to any port on the switch using a standard Ethernet cable; make
sure the switch port LED is lit. 6. In a Web browser, enter the switch default IP address (192.168.1.77) and Subnet
Mask (255.255.255.0). The Login page should display. 7. Enter the factory default username (admin) and
password (admin) on the Login page. 8. Click the “Login” button to log into the switch. See the
Web User Guide
for more information.
Initial Switch Config via CLI: 1. Use an RJ-45 cable to connect a terminal or PC/terminal emulator to the switch
port to access the CLI. 2. Attach the RJ-45 serial port on the switch front panel to the cable for Telnet/CLI
configuration. 3. Attach the other end of the DB-9 cable to a PC running Telnet or a terminal emulation program
such as HyperTerminal or TeraTerm. 4. After powering up the switch for the first time, you can perform the initial
switch configuration using the CLI (Command Line Interface). See the
CLI Reference
for other switch features.
Contact Us : Transition Networks | 10900 Red Circle Drive | Minnetonka, MN 55343 USA | tel: +1.952.941.7600
| toll free: 1.800.526.9267 | fax: 952.941.2322 | web: https://www.transition.com
Andere Handbücher für SM24TBT2DPA
2
Inhaltsverzeichnis
Andere Transition Networks Schalten Handbücher
Transition Networks
Transition Networks SM24T6DPA Bedienungsanleitung
Transition Networks
Transition Networks SISTF10xx-130-LR(T) Bedienungsanleitung
Transition Networks
Transition Networks SISPM1040-382-LRT Bedienungsanleitung
Transition Networks
Transition Networks E-MUX-SA05 Bedienungsanleitung
Transition Networks
Transition Networks SM24DPB Bedienungsanleitung
Transition Networks
Transition Networks SM24DPa Bedienungsanleitung
Transition Networks
Transition Networks Milan MIL-SM8002TG Bedienungsanleitung
Transition Networks
Transition Networks HB-E-TX-8 Bedienungsanleitung
Transition Networks
Transition Networks SM24T6DPA Bedienungsanleitung
Transition Networks
Transition Networks SISPM1040-384-LRT-C Bedienungsanleitung
Transition Networks
Transition Networks SM24DP4XA Bedienungsanleitung
Transition Networks
Transition Networks SISPM1040-3-L Series Bedienungsanleitung
Transition Networks
Transition Networks SM TAT4X Series Bedienungsanleitung
Transition Networks
Transition Networks SISPM1040-384-LRT-C Bedienungsanleitung
Transition Networks
Transition Networks SISTM1040-262D-LRT Bedienungsanleitung
Transition Networks
Transition Networks SISTF1010-180-LRT Bedienungsanleitung
Transition Networks
Transition Networks SM24-1000SFP-AH Bedienungsanleitung
Transition Networks
Transition Networks SM TAT4X Series Bedienungsanleitung
Transition Networks
Transition Networks SM8TAT2SA Bedienungsanleitung
Transition Networks
Transition Networks SISPM1040-3 L Series Bedienungsanleitung
