Transition Networks SM24DPB Bedienungsanleitung

Transition Networks SM24DPB Quick Start Guide

33680 Rev. B https://www.transition.com Page 1 of 2

SM24DPB

(20) 100/1000Base-X SFP Ports + (4) 100/1000Base-X

SFP/RJ-45 Combo Ports

Quick Start Guide

Safety Warnings and Cautions

See the Install Guide for important Safety Warnings and Cautions, Compliance, and Safety Statements.

See the Install Guide for Network Planning, Selecting a Site, Ethernet Cabling, Mounting, Installing an SFP,

and Connecting to a Power Source. The SM24DPB provides 20 GbE SFP ports, 4 Combo GbE RJ45/SFP ports and a DB9

Console port, with built-in AC and DC dual power supplies. Note: Make all cable connections before connecting Power.

Front Panel

1000BASE-T Ports: The switch has 10/100/1000BASE-T RJ-45 ports. All RJ-45 ports

support automatic MDI/MDI-X operation, auto-negotiation and IEEE 802.3x auto-

negotiation of flow control, so the best data rate and transmission are set automatically.

SFP Transceiver Slots: The switch supports SFP transceiver slots port 1 to port 24, ports

21 to 24 are shared with RJ-45 (ports 21-24 are combo interface RJ45/SFP). For

information on the recommended standards for fiber optic cabling, see the Install Guide. See the Transition Networks

SFP webpage for all related information on Transition Networks SFPs.

System Status and Port LEDs: The SM24DPB switch includes system and

port LEDs that simplify installation and troubleshooting. The LEDs are located

on left hand side of the front panel. See the Install Guide for details.

Power Supply Sockets: There are dual power inputs on the front for power

redundancy. The switch has a 100~240 VAC power socket for AC power Input

and a positive or negative 24-72VDC power input via the terminal block.

Ethernet Cabling

To ensure proper operation when installing the switch into a network, make sure that the current cables are suitable

for 100BASE-TX or 1000BASE-T operation.

RJ-45 Connection SFP Transceiver

Power Connection Warning: Connect the power supply to the switch first, then connect the power supply to power.

Otherwise catastrophic product failure may occur. 1. Verify that power is off to the DC circuit that you are going to attach

to the switch DC-input connector. This can be either of the two power supplies (AC-input or DC-input) or site source DC.

2. Added precaution: place an appropriate safety flag and lockout device at the source power circuit breaker or place a

piece of adhesive tape over the circuit breaker handle to prevent accidental power restoration while you are working on

the circuit. Power Disconnection: To disconnect switch power after a successfully boot: 1. Turn off power to the switch.

2. Disconnect the cables.

Triangle

indicates bottom

of SFP cage

SFP Module

Label side top

of SFP module

Bale

Clasp

Switch

Transition Networks SM24DPB Quick Start Guide

33680 Rev. B https://www.transition.com Page 2 of 2

Connecting to Power

Connecting to AC Power Source: You can plug or remove an AC power cord from the AC socket.

1. Insert the AC power cord directly into the AC socket on the front of the switch.

2. Plug the other end of the power cord into an AC power source.

3. Check the front-panel LEDs as the device is powered on to be sure the

POWER LED is lit. If not, make sure the power cable is correctly plugged in.

Connecting to DC Power Source

1. Insert the negative or positive voltage DC power source wires into the DC

INPUT terminals. 2. Use a small flat-blade screwdriver to tighten the wire-

clamp screws on the front of the terminal block connector to keep the DC

wires from pulling loose. 3. Insert the terminal block connector prongs into the terminal block receptor.

4. Check the SYS LED. If it is ON, the power connection is correct. See the Install guide for details.

Connecting to the Console Port: The switch front panel DB-9 serial port is used to connect to the switch for out-of-band

console configuration. The command line interface can be accessed from a terminal or a PC running a terminal emulation

program. The Console port defaults are: Baud rate=115,200 bps, Character Size=8 characters, Parity=None, Stop bit=One,

Data bits=8, and Flow control=none.

You can access the CLI via either a direct serial connection to the device or a Telnet session. The default login username

and password are both admin. After you login successfully, the prompt displays “<sys_name>#“ meaning you are an

administrator for the Switch. If not logged as administrator, the prompt is shown as “<sys_name>>”, meaning you can

only perform as a guest. Each CLI command has a specific privilege level.

Defaults: The default values are: IP Address=192.168.1.77,

Subnet Mask=255.255.255.0, Default Gateway=192.168.1.254,

Username=admin, and Password=admin.

Web Management via Web GUI: After the managed switch has been configured in the

CLI via the switch’s serial interface, you can access it from a web browser.

For instance, type http://192.168.1.77 in the address row in a web browser; the

and access authentication.

The default username and password are both “admin”. For first time use, enter the

default username and password, and then click the <Login> button.

When the login process is complete, the SM24DPB web GUI displays.

Related Manuals: These manuals tell how to operate and use the management

functions of the switch:

SM24DPB Install Guid

e (33681),

User

Guide

(33682), and

CLI

Reference

(33683). For Transition

Networks Manuals go to the Product Support webpage (no logon required).

Transition Networks * 10900 Red Circle Drive * Minnetonka, MN 55343 * tel: +1.952.941.7600 | toll free:

1.800.526.9267 | fax: 952.941.2322 | sal[email protected] | techsupport@transition.com |

Andere Handbücher für SM24DPB

Inhaltsverzeichnis

Andere Transition Networks Schalten Handbücher

Transition Networks

Transition Networks SISPM1040-3248-L Bedienungs- und Wartungsanleitung

Transition Networks

Transition Networks SISTM1040-262D-LRT Bedienungsanleitung

Transition Networks

Transition Networks SM12DP2XA Bedienungsanleitung

Transition Networks

Transition Networks SM4T4DPA Bedienungsanleitung

Transition Networks

Transition Networks SM24DPB Bedienungsanleitung

Transition Networks

Transition Networks SISPM1040-362-LRT Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-HB-0402 Bedienungsanleitung

Transition Networks

Transition Networks PSV-2/14-45 Bedienungsanleitung

Transition Networks

Transition Networks SM8TAT2SA Bedienungsanleitung

Transition Networks

Transition Networks SISTP1040-342-LRT Bedienungsanleitung

Transition Networks

Transition Networks SISTF10xx-130-LR(T) Bedienungsanleitung

Transition Networks

Transition Networks SISTM10xx-162-LR(T) Bedienungsanleitung

Transition Networks

Transition Networks 1005 Bedienungsanleitung

Transition Networks

Transition Networks SISPM1040-582-LRT Bedienungsanleitung

Transition Networks

Transition Networks SM8TAT2SA Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-HB-1600 Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-HB-0403 Bedienungsanleitung

Transition Networks

Transition Networks SM24TAT2DPA Bedienungsanleitung

Transition Networks

Transition Networks E-FL-HB-0400 Bedienungsanleitung

Transition Networks

Transition Networks SM24TBT2DPA Bedienungsanleitung

Transition Networks

Transition Networks SISTG1040-242-LRT Bedienungsanleitung

Transition Networks

Transition Networks SM24TBT2DPA Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-HB-0802 Bedienungsanleitung

Transition Networks

Transition Networks SISTM1040-262D-LRT-B Bedienungs- und Wartungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung