Transition Networks FAST ETHERNET E-TX-MC01 Bedienungsanleitung

TRANSITION Networks copper transceivers (E-TX-MC01) connect Fast Ethernet™ hubs

and/or terminal devices, through a Media Independent Interface (MII) connector, to

10BASE-T copper cable or to 100BASE-TX copper cable.

E-TX-MC01

Provides an MII

connector and an RJ-

45 10BASE-

T/100BASE-TX

connector to

unshielded twisted-

pair or shielded

twisted-pair copper

cable.

A set of switches on the front of the transceiver can be used to set a unique physical

address for each transceiver. Transceivers can be configured to

autonegotiate or to force either 10Mb/sec half-duplex mode or

100Mb/sec half-duplex mode.

An MDI/MDI-X switch on the side of the transceiver can be

used to set the copper cable configuration to straight-through or

to crossover.

Fast Ethernet™ Copper Transceiver

E-TX-MC01

USER’S GUIDE

TRANSCEIVER TECHNICAL SPECIFICATIONS

Standards IEEE 802.3

Case dimensions 2.8" x 1.75" x 0.75" (71mm x 43mm x 18mm)

Maximum in series: Two (2)

Environment Temperature: 0-40°C (32° to 104° F )

Humidity 10-90%, non condensing

Altitude 0-10,000 feet

Warranty Five years

Status LEDs provide the following information:

Minneapolis, MN 55344 USA

PL/FDX Illuminated green LED indicatesthe

transceiver is operating in full-duplex

mode.

10/100 Illuminated green LED indicates the

transceiver is operating at 100Mb/s.

Collision: Illuminated green LED indicates

signal collisions on the Ethernet

cable.

RX Flashing or illuminated green LED indicates packet(s) are being received.

TX Flashing or illuminated green LED indicates packet(s) are being transmitted.

Link Illuminated green LED indicates the unit is receiving link pulses from a

compliant device.

Power: Illuminated green LED indicates connection to external power

Compliance Information

UL Listed

C-UL Listed (Canada)

CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on

the radio interference regulations of the Canadian Department of Communications.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners. 33097.B

Config. Switches

123 4567

PL/FDX

MDI MDI-X

E-TX-MC01

UTP/STP Copper

Setting the Transceiver Physical Address

Additive switch settings allow a physical address to be set by selecting (or not

selecting) among the following:

Switch 1 DOWN 201

Switch 2 DOWN 212

Switch 3 DOWN 224

Switch 4 DOWN 238

Switch 5 DOWN 2416

In the switch setting shown above, the

transceiver physical address is set to 1 (1+0+0+0+0).

NOTE: 1=ON, 0=OFF

123 45

Address (1-5)

OFF OFF

100BASE-TX

TRANSCEI ER

E-TX-MC01

Link

Power

123 45

Address (1-5)

OFF

Collision

Link

Power

Collision

10/100

PL/FDX

10BASE-T or 100BASE-TX Hub

Hub with MII connector

100BASE-TX

TRANSCEI ER

E-TX-MC01

Collision

Link

Power

123 45

Address (1-5)

OFF

MDI-X switch setting

100BASE-TX

TRANSCEI ER

E-TX-MC01

Collision

Link

Power

123 45

Address (1-5)

OFF

100BASE-TX

TRANSCEI ER

E-TX-MC01

Collision

Link

Power

123 45

Address (1-5)

OFF MDI switch setting

1. Is the power LED on the transceiver illuminated?

NO • Verify that the transceiver is installed properly in the MII port and that the device is

powered ON?

• Contact Technical Support at (800) 260-1312 or at (800) LAN-WANS.

YES • Proceed to step 2.

2. Is the Link LED illuminated?

NO • Check the copper cables for proper connection. (If possible, try a different cable.)

• Try setting a non-zero physical address.

• Contact Technical Support at (800) 260-1312 or at (800) LAN-WANS.

YES • Proceed to step 3.

3. Is the copper cable connected properly?

NO • Verify that straight-through copper cable is installed and that MDI-MDI-X switch is set

correctly.

• Contact Technical Support at (800) 260-1312 or at (800) LAN-WANS.

YES C T h i l S (800) 260 1312 (800) LAN WANS

Troubleshooting the Transceiver

If the E-TX-MC01 transceiver fails, determine the answers to the following questions:

Installation Notes

Straight Through/Crossover Cable Requirements and Pin Specifications

NOTE: Straight-through/crossover requirements are satisfied using the MDI/MDI-X switch with

straight-through cable. Cable connections between a hub and the media converter require the

MDI/MDI-X switch to be set to MDI. Cable connections between the media converter and a

terminal, transceiver or NIC require the switch to be set to MDI-X

Using small flatblade screwdriver or similar tool

and referring to label at front of media converter,

set MDI/MDI-X switch position for site installation.

MDI

position MDI-X

position

• Be certain that 10BASE-T/100BASE-TX

MDI/MDI-X switch is set correctly for site

installation. .

• Set Switches according to site installation:

Switches 1-5: The transceiver is shipped with

rocker switch 1 set to the default ON=UP

and with switches 2-5 set to the default

OFF=DOWN, setting the transceiver physical

address to a value of “1”.

In all known cases, the default rocker switch 1-5

setting is the correct physical

address for network installations.

ONLY IF THIS ADDRESS

SHOULD FAIL, refer to the chart

on the back page for direction for

setting the binary transceiver

physical address to a site-specific value from 1 to 31.

Switch 6-7: The transceiver is shipped with rocker switches 6 and 7 set to

the default OFF=DOWN, which sets the data-transfer mode to “auto-

negotiation”..

• Set switch 6 to ON=UP when the transceiver is connected to a

100BASE-TX half-duplex device.

• Set switch 7 to ON=UP when the transceiver is connected to a

10BASE-T half-duplex device.

CABLE SPECIFICATIONS

The physical characteristics of the media cable must meet or exceed IEEE

802.3u 100BASE-TX specifications.

100BASE-TX CABLE SPECIFICATIONS

Category 5 wire or better is required. Either shielded twisted pair

(STP) or unshielded twisted pair (UTP) can be used. Use a straight-

through cable configuration (see back page).

Category 5: Gauge 24 to 22 AWG

Attenuation 20 dB/1000’ @ 10 MHz

Impedance 100 Ω±10% @ 10 MHz

Maximum Cable Distance: 100 meters (330 feet)Maximum

Config. Switches

123 4567

PL/FDX

MDI MDI-X

100BASE-FX

TRANSCEI ER

E-FX-MC01

123 45

Address (1-5)

OFF OFF

Inhaltsverzeichnis

Andere Transition Networks Transceiver Handbücher

Transition Networks

Transition Networks E-TBT-MC04 Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-MCO1 Bedienungsanleitung

Transition Networks

Transition Networks E-FRL-MC01A Bedienungsanleitung

Transition Networks

Transition Networks TN-GB-ESX5 Bedienungsanleitung

Transition Networks

Transition Networks TN-SFP-10G Series Bedienungsanleitung

Transition Networks

Transition Networks ETHERNET E-TBT-MC01(LC) Bedienungsanleitung

Transition Networks

Transition Networks ETHERNET E- FL/RED-MC01(SMA) Bedienungsanleitung

Transition Networks

Transition Networks E-FRL-MC04 Bedienungsanleitung

Transition Networks

Transition Networks E-CX-MC02 Bedienungsanleitung

Transition Networks

Transition Networks Micro-ceiver E-FRL-MC01C Bedienungsanleitung

Transition Networks

Transition Networks TN-SFP-ELX1 Bedienungsanleitung

Transition Networks

Transition Networks E-FX-MC01 Bedienungsanleitung

Transition Networks

Transition Networks E-FRL-MC05 Bedienungsanleitung

Transition Networks

Transition Networks TN-CWDM-SFP-1xx0 Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-MC05 Bedienungsanleitung

Transition Networks

Transition Networks E-FRL-MC03 Bedienungsanleitung

Transition Networks

Transition Networks E-CX-MC01B Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-MC05 Bedienungsanleitung

Transition Networks

Transition Networks E-CX-MC22 Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-MC03 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung