Travis Industries ProBuilder 36 Bedienungsanleitung
ProBuilder 36/42 Ember-Glo Light Kit (MV / GSB2)
SKU# 94400897
Page 1 of 9 17602033 - Printed 8/28/18 © Travis Industries, Inc.
Compatibility
•ProBuilder 36CF
•ProBuilder 42CF
Packing List
•Light Assembly with Wire Leads & Seal Plate
•Power Harness
•Rheostat Assembly
•(2) 8-32 KEPS nuts (use 11/32” nut driver)
•(4) Halogen Bulbs
•Molex Dummy Plug (used only on MV
appliances without a blower)
•Ember Glass
•(1) can of paint
•(2) 8-32 X 3/8” screws
Tools Required
•11/32” Nut Driver/Wrench
•1/4” Nut Driver/Wrench
ProBuilder 36/42 Ember-Glo Light Kit (MV / GSB2)
SKU# 94400897
Page 2 of 9 17602033 - Printed 8/28/18 © Travis Industries, Inc.
Installation Notes
Install The Blower First
The blower is installed at the back of the fireplace. If using, we recommend installing it first so its installation does not
interfere with the light wiring.
WARNING: Disable power to the fireplace while installing the lights (disable the service breaker). Do not
activate power to the fireplace until the light kit is fully installed and grounded.
Do not connect 110-120 VAC to the gas control valve or wiring system of this appliance.
Installation
1. Disable power to the fireplace (turn the service breaker off).
2. Remove the screen and glass frame (see manual for details).
3. Carefully remove the logs and embers (if applicable).
4. Remove the media tray skirt.
5. Remove the media tray. Remove the two screws that secure the media tray to the front of the grate
assembly. Remove the tray and keep the screws for reinstallation (see below).
ProBuilder 36/42 Ember-Glo Light Kit (MV / GSB2)
SKU# 94400897
Page 3 of 9 17602033 - Printed 8/28/18 © Travis Industries, Inc.
6. Remove the cover plate on the right side of the firebox floor (Discard the cover plate. Keep the screws for
reinstallation). Leave the gasket it place.
7. Pass the light assembly wires through the hole (and gasket) uncovered in the previous step. Secure the
attached seal plate to the firebox floor using the two screws removed in step 7 (see below). Once installed,
remove all excess wiring inside the firebox by pulling the wires from below.
8. Possition the light assembly in front of the grate assembly (see photo below).
Remove Cover – Leave gasket
Seal Plate
ProBuilder 36/42 Ember-Glo Light Kit (MV / GSB2)
SKU# 94400897
Page 4 of 9 17602033 - Printed 8/28/18 © Travis Industries, Inc.
9. Allign the (2) holes in the back of the light assembly with the (2) LOWER holes on the front of the grate
assembly. Secure the assembly to the burner housing using the included screws.
10. Install the (4) bulbs into the sockets by gently inserting the bulbs pins into the holes on the socket.
NOTE: .Take care not to touch the replacement bulbs with your fingers. Residue (oil,etc.) left on the bulb will
reduce the bulb’s life span. Use foam packing or paper towel to hold the bulb when installing.
ProBuilder 36/42 Ember-Glo Light Kit (MV / GSB2)
SKU# 94400897
Page 5 of 9 17602033 - Printed 8/28/18 © Travis Industries, Inc.
11. Reinstall the media tray and skirt.
12. Locate the “Power In” wires connected to the junction box on the right side of the firelace. The wires are
white and have large white Molex connectors at the end.Connect the male Molex connecter, on the
harness included with this kit, to the Molex connector labeled “Lights”.
13. Connect the wires from the light assembly to the wires labeled “lights” on the light assembly wire harness.
ProBuilder 36/42 Ember-Glo Light Kit (MV / GSB2)
SKU# 94400897
Page 6 of 9 17602033 - Printed 8/28/18 © Travis Industries, Inc.
14. Disconnect the dashboard from the fireplace (4 screws hold it in place) and place it face down in front of
the fireplace.
NOTE:The rheostat shown in the picture above operates the blower. If a blower is not being installed on your
fireplace, the blower rheostat will not be present on the dashboard.
15. Place the rheostat assembly onto the studs on the right side of the dashboard and secure using the 2
nuts included with the kit. Use an 11/32” nut driver to tighten the nuts.
NOTE: The bracket on the rheostat must face upwards so the control wheel fits through the slot on the dashboard
(see pictures below).
ProBuilder 36/42 Ember-Glo Light Kit (MV / GSB2)
SKU# 94400897
Page 7 of 9 17602033 - Printed 8/28/18 © Travis Industries, Inc.
16. Connect the two wires from the rheostat to the wires labeled “rheostat” on the wire harness
(polarity does not matter).
17. Reinstall the dashboard onto the fireplace.
18. Install the logs (see installation manual for details).
Ember Glass Installation
•Make sure the media tray skirt is in place. The skirt hooks over the front of the ember platform and slopes
outward toward the glass. The skirt helps keep the glass and ember material from falling off the platform
when the glass is removed.
•Locate the perforations in front of the log grate.
•Place a thick layer of the ember glass over the perforations making sure to cover all of the holes
completely.
ProBuilder 36/42 Ember-Glo Light Kit (MV / GSB2)
SKU# 94400897
Page 8 of 9 17602033 - Printed 8/28/18 © Travis Industries, Inc.
•Lightly fog the ember glass with the black touch-up paint provided. Check the appearance with the lights
on and add additional paint, as needed, for a realistic glowing ember appearance.
NOTE: If power is supplied to the fireplace, it can be helpful to turn the lights on while painting so you can
determine an appropriate amount of paint for a realistic ember appearance.
NOTE: We recommend that you use a piece of paper, cardboard as a shield to mask the log grate and burner
from overspray (see below).
Ember Material Installation
•Once the ember glass installation is complete, place a generous amount of ember material on the firebox
floor on either side of the firebox. Completely cover any visible metal on the firebox floor.
NOTE: Make sure no ember material is placed directly on the burner. Apply rockwool as needed for realistic ember
appearance.
HINT: Add a few randomly placed ember chunks over the ember bed glass to produce a more realistic appearance.
Rock Wool Placement
The included rock wool is placed on top of the burner to enhance the glow from the burner. The rock wool works
best when it is applied in a very thin layer. The best method for applying the rock wool is to brush it on to the
burner. Compress a clump of rockwool between your thumb and forefinger. Use a stiff brush to apply a thin layer
of rockwool fibers onto the burner. Do not use the entire bag of rockwool. Use only a small amount and save the
remainder. Over-use of rockwool will diminish the glow and may cause sooting or other adverse conditions.
ProBuilder 36/42 Ember-Glo Light Kit (MV / GSB2)
SKU# 94400897
Page 9 of 9 17602033 - Printed 8/28/18 © Travis Industries, Inc.
Bulb Replacement
•Remove the screen and glass assemblies (see appliance manual for details).
•Remove the media tray skirt (see step 4).
NOTE: Take care not to disturb the ember bed media on the media tray when removing and replacing the media
tray skirt.
•The bulbs are now visible. Grasp the bulb with your thumb and forefinger and gently pull the bulb straight
out of the socket.
•Install the replacement bulbs into the sockets by gently inserting the bulbs pins into the holes on the
socket..
NOTE: .Take care not to touch the replacement bulbs with your fingers. Residue (oil,etc.) left on the bulb will
reduce the bulbs life span. Use foam packing or paper towel to hold the bulb when installing.
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Travis Industries Kaminzubehör Handbücher
Travis Industries
Travis Industries Illuminations 4915 Bedienungsanleitung
Travis Industries
Travis Industries 1750 Bedienungsanleitung
Travis Industries
Travis Industries Fireplace Xtrordinair 96300770 Bedienungsanleitung
Travis Industries
Travis Industries 96100593 Bedienungsanleitung
Travis Industries
Travis Industries 91500565 Bedienungsanleitung
Travis Industries
Travis Industries 616 GSR Insert Bedienungsanleitung
Travis Industries
Travis Industries Arbor Bedienungsanleitung
Travis Industries
Travis Industries 96100594 Bedienungsanleitung
Travis Industries
Travis Industries 4237 Bedienungsanleitung
Travis Industries
Travis Industries 95900352 Bedienungsanleitung
Travis Industries
Travis Industries DVL GSR Bedienungsanleitung
Travis Industries
Travis Industries DVS EG Firebacks Bedienungsanleitung
Travis Industries
Travis Industries 94700881 Bedienungsanleitung
Travis Industries
Travis Industries Rosario DVS Face Bedienungsanleitung
Travis Industries
Travis Industries GreenSmart DFC Montage- und Bedienungsanleitung
Travis Industries
Travis Industries 95100055 Bedienungsanleitung
Travis Industries
Travis Industries Illuminations 4915 Bedienungsanleitung
Travis Industries
Travis Industries shield 6015 Bedienungsanleitung
Travis Industries
Travis Industries 616 DF Bedienungsanleitung
Travis Industries
Travis Industries Olympic Bedienungsanleitung
Beliebte Kaminzubehör Handbücher anderer Marken
Bronpi
Bronpi KIT-1 Bedienungsanleitung
Town & Country Fireplaces
Town & Country Fireplaces 22150051 Bedienungsanleitung
Superior
Superior ASD3628-TI Bedienungsanleitung
pleasant hearth
pleasant hearth OFP28WG Bedienungsanleitung
IHP
IHP Astria Series Bedienungsanleitung
Firegear
Firegear FG-H-2110SS Bedienungsanleitung
