Travis Industries 1750 Bedienungsanleitung

1750 Wood Insert



Owner's Manual

Masonry Fireplace Insert

Zero-Clearance (Metal) Fireplace Insert

Save these instructions for future reference

SAFETY NOTICE:

If this appliance is not properly installed, a house fire may

result. For your safety, follow the installation directions.

Contact local building or fire officials about restrictions and

installation inspection requirements in your area.

$10.00 100-01234

4141211 Listed

Tested to: U.L. 1482 & ULC S628

2 Introduction

Introduction

We welcome you as a new owner of a 1750 wood-burning fireplace insert. In purchasing a 1750

fireplace insert you have joined the growing ranks of concerned individuals whose selection of an energy

system reflects both a concern for the environment and aesthetics. This insert is one of the finest

appliances the world over. This manual will explain the installation, operation, and maintenance of this

appliance. Please familiarize yourself with the Owner's Manual before operating your appliance and save

the manual for future reference. Included are helpful hints and suggestions which will make the

installation and operation of your new appliance an easier and more enjoyable experience. We offer our

continual support and guidance to help you achieve the maximum benefit and enjoyment from your

appliance.

Important Information

No other 1750 fireplace insert appliance has the same

serial number as yours. The serial number is

stamped onto the label on the back of the appliance.

This serial number will be needed in case you require

service of any type.

Model: 1750 Fireplace Insert

Serial Number:

Purchase Date:

Purchased From:

Mail your Warranty Card Today, and Save Your Bill

of Sale.

To receive full warranty coverage, you will need to

show evidence of the date you purchased your

appliance. Do not mail your Bill of Sale to us.

We suggest that you attach your Bill of Sale to this

page so that you will have all the information you need

in one place should the need for service or information

occur.

Table of Contents 3

General Information

Introduction & Important Information.......................... 2

Safety Precautions..................................................... 4

Features & Specifications .......................................... 6

Fireplace Insert Installation

Planning The Installation............................................ 7

Preparation for Installation.................................... 7

Additional Accessories Needed for Installation..... 7

Installation Considerations ................................... 7

Additional Requirements for Canada.................... 7

Fireplace Requirements............................................. 8

Fireplace Altered Tag................................................. 8

Insert Placement Requirements................................. 9

Hearth Requirements................................................. 9

Masonry Fireplace Requirements .............................. 9

Zero-Clearance (Metal) Fireplace Requirements....... 10

Drafting Performance................................................. 11

Insert Rollers.............................................................. 11

Flue Installation.......................................................... 11

Surround Panel Installation........................................ 12

Insert with Positive Connection.................................. 14

Insert with Direct Connection (Masonry Fireplace)..... 14

Operating Your Appliance

Safety Notice.............................................................. 15

Before Your First Fire................................................. 15

Opening the Door....................................................... 15

Bypass Operation....................................................... 17

Starting a Fire ............................................................ 17

Adjusting the Burn Rate............................................. 19

Ash Removal.............................................................. 20

Optional Blower Operation......................................... 21

Re-Loading the Stove ................................................ 22

Overnight Burn........................................................... 22

Normal Operating Sounds.......................................... 22

Hints for Burning........................................................ 23

Selecting Wood.......................................................... 23

Troubleshooting ......................................................... 24

Maintaining Your Appliance

Daily Maintenance...................................................... 26

Remove Ash .............................................................. 26

Clean The Glass........................................................ 26

Monthly Maintenance................................................. 27

Door and Glass Inspection......................................... 28

Check For Creosote Buildup...................................... 28

Yearly Maintenance ................................................... 28

Touch Up Paint.......................................................... 28

Blower Cleaning......................................................... 28

Firebrick and Baffle Inspection................................... 28

Door Parts.................................................................. 29

Replacing the Glass................................................... 29

Replacing the Door Gasket........................................ 29

Replacing the Door Handle........................................ 29

Firebox Parts.............................................................. 30

Air Tube Removal and Replacement ......................... 31

Warranty....................................................................... 33

Listing Information.................................................... 34

Index.............................................................................. 36

4 Safety Precautions

The viewing door must be

closed and latched during

operation.

Smoke from this appliance may

active a smoke detector when

the door is open.

Never block free airflow through

the air vents on this appliance.

Gas

Gasoline or other flammable

liquids must never be used to

start the fire or "Freshen Up" the

fire. Do not store or use

gasoline or other flammable

liquids in the vicinity of this

appliance.

This appliance is designed and

approved for the burning of cord

wood only. Do not attempt to

burn any other type of fuel other

than cord wood in this

appliance, it will void all

warranties and safety listings.

ASHES

Ashes must be disposed in a

metal container with a tight lid

and placed on a non-

combustible surface well away

from the home or structure.

Do not touch the appliance while

it is hot and educate all children

of the danger of a high-

temperature appliance. Young

children should be supervised

when they are in the same room

as the appliance.

36"

Keep furniture, drapes, curtains,

wood, paper, and other

combustibles a minimum of 36"

away from the front of the

appliance.

This appliance must be properly

installed to prevent the

possibility of a house fire. The

instructions must be strictly

adhered to. Do not use

makeshift methods or

compromise in the installation.

Contact your local building

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance company

of this appliance as well.

Inspect the chimney connector

and chimney at least twice

monthly and clean if necessary.

Creosote may build up and

cause a house fire.

Do not connect this appliance to

any chimney serving another

appliance.

Type

HT Clay

Liner

This appliance must be

connected to a listed high

temperature (UL 103 HT)

residential type chimney or an

approved masonry chimney with

a standard clay tile, or stainless

steel liner.

Safety Precautions 5

Do not place clothing or other

flammable items on or near this

appliance.

Never try to repair or replace

any part of this appliance unless

instructions are given in this

manual. All other work must be

done by a trained technician.

Do not make any changes or

modifications to an existing

masonry fireplace or chimney to

install this appliance.

This wood heater has a

manufacturer-set minimum low

burn rate that must not be

altered. It is against federal

regulations to alter this setting or

otherwise operate this wood

heater in a manner inconsistent

with operating instructions in this

manual.



Allow the appliance to cool

before carrying out any

maintenance or cleaning.

Overfiring the appliance may

cause a house fire. If a unit or

chimney connector glows, you

are overfiring.

Maintain the door and glass seal

and keep them in good

condition.

Do not operate this heater with

broken or missing glass.

Avoid placing wood against the

glass when loading. Do not

slam the door or strike the glass.

Do not use a grate or other

device to elevate the fire off of

the firebox floor. Burn the fire

directly on the bricks.

This

Manual

Do not throw this manual away.

This manual has important

operating and maintenance

instructions that you will need at

a later time. Always follow the

instructions in this manual.

Travis Industries, Inc. grants

no warranty, implied or

stated, for the installation or

maintenance of your

appliance,and assumes no

responsibility of any

consequential damage(s).

Smoke and CO Detectors: Make sure your home has a working smoke detector, especially near any bedrooms. We

recommend having a smoke and/or CO detector in the same room as the wood heater for additional safety.

Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of combustion of such

fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm.

California Health & Safety Code Sec. 25249.6

6 Stove Installation (for qualified installers only)

Installation Options

Masonry Fireplace Insert

Zero-Clearance (Metal) Fireplace Insert

Features

2.2 Cubic Foot Firebox Volume

Single Operating Control

Accepts Logs Up to 18" Long

Steel Plate Construction (5/16" & 1/4")

Heavy Duty Refractory Firebrick

Standard High-Tech Blower

Optional High-Tech Blower

Heating Specifications

Approximate Maximum Heating Capacity (in square feet)* 1,200 to 2,000

Maximum Burn Time Up to 10 Hours

* Heating capacity will vary depending on the home's floor plan, degree of insulation, and the outside

temperature. It is also affected by the quality and moisture level of the fuel.

This model was not tested for efficiency however it is assigned a default efficiency of 63% by the EPA

under previous subpart AAA. Efficiency of this wood heater will be affected by the operational burn rate

and the moisture content of the wood used as fuel.

Dimensions

21-3/8"

(543mm)

13-1/8" (334mm)

21-5/8" (550mm)

380 Lbs. (170 Kg)

5-3/16"

(132mm)

19-3/4"

(502mm)

10" (254mm)

24-1/4"

(616mm)

18-3/4"

(477mm)



Figure 1

(a) Measure side and top clearances from the top plate. Measure front clearances from the stove face

(b) Fireplace Opening

Emissions

This heater meets the 2015 U.S. EPA’s crib wood emission limits for wood heaters sold after May 15,

2015. Tested to Method 28, 5H this heater has been shown to deliver heat at rates ranging from 9,300 to

42,200 BTU/hr and an emission value of 1.9g/h.

Fireplace Insert Installation (for qualified installers only) 7

SAFETY NOTICE:

Please read this entire manual before you install and use your new room heater. Failure to

follow instructions may result in propertydamage, bodily injury, or even death. Contact

local building or fire officials about restrictions and installation inspection requirements in

your area.

Planning The Installation

We suggest that you have an authorized Travis Industries dealer install your fireplace insert. If you

install the fireplace insert yourself, your authorized dealer should review your installation plans.

Check with local building officials for any permits required for installation of this fireplace insert and

notify your insurance company before proceeding with installation.

The location of your wood heater in your home will decide how affectively the heat produced will spread

throughout your house. Attention to the home design with consideration of natural convection and air

circulation should be taken into account when choosing the placement of your heater within the home.

Preparation for Installation

Check for damage to the exterior of the fireplace insert (dents should be reported, scratches can be

fixed by applying touch up paint).

Check the interior of the firebox (replace cracked firebrick and make sure baffle is in place).

The fireplace insert can be lightened by removing the firebricks and baffle - replace before operation.

Additional Accessories Needed for Installation

Door (shipped separately)

Surround Panels (see page12)

Installation Considerations

Installation Type Considerations

Insert with Positive Flue (Full Reline) (Page 14)

REQUIRED IN CANADA • Utilizes existing masonry or zero clearance fireplace

• Provides best draft

• Easiest to clean

Insert with Direct Connect Flue (Page 14)

NOT APPROVED IN CANADA • Masonry fireplace only

• Provides good draft

• Requires fireplace block-off plate - see page 14

Additional Requirements for Canada

Do not remove bricks or mortar from existing fireplace.

This fireplace insert must be installed with a continuous chimney liner of 6” diameter extending from

the fireplace insert to the top of the chimney. The chimney liner must conform to the Class 3

requirements of CAN/ULC-S636, Standard for Lining Systems for Existing Masonry or Factory-Built

Chimneys and Vents, or CAN/ULC-S640, Standard for Lining Systems for New Masonry Chimneys.

Permanently seal any opening between the masonry of the fireplace and the facing masonry.

Fireplace insert, or surround panels, may be removed to inspect fireplace insert and fireplace.

8 Fireplace Insert Installation (for qualified installers only)

Fireplace Requirements

Figure 2 shows the minimum size requirements for the type of fireplace used.

Non-Combustible Hearth

Combustible Mantel

Non-Combustible Facing

Minimum

Fireplace Size Masonry

Fireplace Z.C. (Metal)

Fireplace

a Height (front) 19.75"502mm19.75"502mm

b Height (rear) 19.75"502mm19.75"502mm

c Width (front) 24.25"616mm26.25"*667mm*

d Width (rear) 21.625"550mm23.625"*601mm*

e Depth 13.125"334mm14.125"*359mm*

f Hearth Depth

(includes insert

depth on hearth

plus required

hearth extension)

26"661mm (US)

- - - - - - - - - - - -

28"712mm

(Canada)

26"661mm (US)

- - - - - - - - - - - -

28"712mm

(Canada)

g Hearth Width 36.25"921mm

- - - - - - - - - - - -

40.25"1023mm

(Canada)

36.25"921mm

- - - - - - - - - - - -

40.25"1023mm

(Canada)

h Facing Width 50.25"1277mm48.25"1226mm

i Facing Height

w Mantel

Shield

47.25"1201mm

- - - - - - - - - - - -

39.25"997mm

30.75"782mm

- - - - - - - - - - - -

notapplicable

j Mantel Height

w Mantel

Shield

49.25"1251mm

- - - - - - - - - - - -

41.25"1048mm

42.75"1086mm

- - - - - - - - - - - -

notapplicable

Figure 2 * 1” (26mm) Clearance to fireplace walls is required for ZC Fireplaces.

Fireplace Altered Tag

Attach the "This fireplace has been altered..." plate to the fireplace (use two screws or other suitable

method). You may wish to place it in a location where it will be covered by the surround panels.

Fireplace Insert Installation (for qualified installers only) 9

Insert Placement Requirements

The insert must be placed so that no combustibles are within, or can swing within (e.g. drapes,

doors), 36" (915) of the front of the insert (see “q” below).

Insert and hearth must be installed on a level, secure floor

The minimum clearances, facing, and hearth requirements in shown below must be met. Follow the

clearances for the type of fireplace being used – (masonry or zero-clearance-metal).





Side

Wall

Combustible Mantel

Combustible Top Facing

Non-Combustible

Hearth

Facing

Figure 3

Minimum

Clearances Masonry

Fireplace Z.C. (Metal)

Fireplace

k Sidewall 15"381mm 30"762mm

l Side Facing 13"331mm 12"305mm

m Top Facing

w Mantel Shield

28.5"724mm

- - - - - - - - - - -

20.5"521mm

12"305mm

- - - - - - - - - - -

notapplicable

n Mantel

w Mantel Shield

30.5"775mm

- - - - - - - - - - -

22.5"572mm

24"610mm

- - - - - - - - - - -

notapplicable

o Front Hearth

(does not

include insert

extension “x”)

16" 407mm

(US)

- - - - - - - - - - -

18” 458mm

(Canada)

16" 407mm

(US)

- - - - - - - - - - -

18” 458mm

(Canada)

p Side Hearth 6"153mm

(US)

- - - - - - - - - - -

8" 204mm

(Canada)

6" 153mm

(US)

- - - - - - - - - - -

8" 204mm

(Canada

q Front of Insert 36"

915mm 36"

915mm

x Extension Onto

Hearth 10" 254mm 10" 254mm

Hearth Requirements

Must extend 16" (USA) or 18” (Canada) in front of the insert and 6” (USA) or 8" (Canada) on both sides.

Must be non-combustible and at least .018" thick (26 gauge)

Masonry Fireplace Requirements

CANADA ONLY:

The fireplace insert must be installed with a continuous chimney liner of 6” diameter extending from the

fireplace insert to the top of the chimney. The chimney liner must conform to the Class 3 requirement of

Can/ULC S635, Standard Lining Systems for Existing Masonry or Factory- Built Chimney & Vents, or

CAN/ULC S640, Standard for Lining Systems for New Masonry Chimneys.

Chimney must have a clay tile liner or a stainless steel liner (positive connection).

Entire fireplace, including chimney, must be clean and undamaged. Any damage must be repaired

prior to installation of the insert.

Chimney height: 15' (4.5M) minimum; 33' (10M) maximum.

Entire fireplace, including chimney, must meet local building requirements.

The fireplace insert must be placed on a masonry hearth built to UBC standards.

10 Fireplace Insert Installation (for qualified installers only)

Zero-Clearance (Metal) Fireplace Requirements

Must be manufactured by one of the following manufacturers:

• Marco • Majestic • Heatilator • Preway • Tempco • Superior

• Heat N Glo • Lennox • Martin • Monesson

Entire fireplace, including chimney, must meet local building requirements

Chimney height: 15' minimum; 33' maximum.

The damper ("A") and grate ("B") must be removed (see illustration below). The smoke shelf ("C"),

internal baffles ("D"), screen ("E"), and metal or glass doors ("F") may be removed (if applicable).

The masonry lining ("G"), insulation ("H"), and any structured rigid frame members (metal sides, floor,

door frame, face of the fireplace, etc. – "I") may not be removed or altered

The chimney on the ZC fireplace must be listed per UL 127 or ULC 610-M87 for all installations. Any

thermal protection component of the fireplace or chimney must remain in place. The fireplace and

chimney must be inspected prior to installation. A NFPA 211 Level II inspection is recommended.

Repairs must be made prior to insert installation. The base of the fireplace must be structurally

sound and able to support the weight of the insert.

The stainless steel liner must be 6” diameter and extend the full height of the chimney (also called a

positive connection or full re-line). This liner must meet type HT (2100°F) requirements per UL 1777

(USA) or ULC S635 with “0” clearance to masonry (Canada). The liner must be attached to the insert

flue collar and to the top of the existing chimney.

We recommend using the listed Travis ZC Liner Kit from Duravent (SKU 98900046, 47, or 48). If you

do not use this kit, you must use the original ZC chimney cap.

The liner support and cap at the top of the chimney must not reduce air flow for the existing air-cooled

chimney system. The Travis ZC Liner Kit includes a cap that meets this provision.

To prevent air from passing up the ZC fireplace chimney (the gap between the liner and chimney) we

recommend sealing the area near the damper. Use non-combustible material to seal this area (non-

backed fiberglass insulation or kaowool).

The convection air channel on the fireplace must not be blocked. Do not block any louvers, grills, or

air passages on the front of the fireplace.

Entire fireplace, including chimney, must meet local building requirements. Permits may be required

for installation. Final approval is contingent upon the authority having local jurisdiction. Inform you

insurance agent of this fireplace insert.

Andere Handbücher für 1750

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries DVL EF Bedienungsanleitung

Travis Industries

Travis Industries LOPI X Bedienungsanleitung

Travis Industries

Travis Industries 564 Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries 42 ProBuilder MV Bedienungsanleitung

Travis Industries

Travis Industries 21 DV RV Bedienungsanleitung

Travis Industries

Travis Industries 564 LedgeStone Bedienungsanleitung

Travis Industries

Travis Industries 616 GSR Bedienungsanleitung

Travis Industries

Travis Industries 564 Bedienungsanleitung

Travis Industries

Travis Industries 864 ST GSR2 Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries 1080 CF Bedienungsanleitung

Travis Industries

Travis Industries 21E Bedienungsanleitung

Travis Industries

Travis Industries 564 HO Bedienungsanleitung

Travis Industries

Travis Industries 99200149 Bedienungsanleitung

Travis Industries

Travis Industries Pro Builder 42 Linear GSB2 Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Deluxe Bedienungsanleitung

Travis Industries

Travis Industries DVL GSR Bedienungsanleitung

Travis Industries

Travis Industries 564 SS GS2 Bedienungsanleitung

Travis Industries

Travis Industries 430 GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 564 DF GSR2 Bedienungsanleitung

Travis Industries

Travis Industries DVS EF Insert Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch