Travis Industries 564 HO Bedienungsanleitung

564 HO GS

Fireplace

Listed by

AS 4553-2008

GMK10022

IAPMO-R&T OCEANA

Built-In Direct Vent Fireplace

Natural Gas or Propane



Residential or Mobile Home

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

This appliance may be installed in

an aftermarket permanently

located, manufactured home (USA

only) or mobile home, where not

prohibited by local codes.

This appliance is only for use

with the type(s) of gas indicated

on the rating plate. A conversion

kit is supplied with the appliance.

Installation Manual

Installer: After installation give this manual to the home-

owner and explain operation of this heater.

Dragon Wholesaling Pty. Ltd.

Unit 2, 16 Lexington Drive

Bella Vista NSW 2153

Australia

2 Introduction

Overview

This manual details the installation requirements for

the 564 HO GS fireplace. For operating and

maintenance instructions, refer to the 564 HO GS

Owner's Manual.

IAPMO-R&T

OCEANA

Gas Mark

GMK10022_02

564 HO GS

Vented Gas Fireplace Heater

Tested to the combustion performance and construction requirements of AS 4553-2008 Gas Space Heating

Appliances. This appliance must be installed in accordance with all local codes.

This 564 appliance is equipped from the factory only for use with Natural Gas and is only for use with the

type of gas indicated on the rating plate. For conversion to LP (Propane) use a certified kit supplied by the

manufacturer. See owner’s manual for information on making these changes.

This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home where

not prohibited by local codes.

This vented gas fireplace heater is not for use with air filters. This appliance must be properly connected to

a venting system in accordance with the manufacturer’s installation instructions. Use only approved

coaxial directvent systems toventthis appliance to the exterior. See owner’s manual for approved brands

of venting.

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause injury or

property damage. Refer to the owner’s information manual provided with this appliance. For assistance or

additional information consult a qualified installer, service agency or the gas supplier.

This appliance is a Vented Gas Fireplace Heater. Not for use with Solid Fuel.

Young children should be carefully supervised at all times when they are in the same room

as the appliance.

Minimum Clearances to Combustibles

FAN TYPEVENTED CIRCULATOR

Blower Electrical Rating: 240V., 1.5 Amps, 50 Hz, 150 Watts

Minimum InletPressure(kPa)

Maximum Inlet Pressure (kPa)

ManifoldPressureon“HI” (kPa)

L.P.

2.74

3.24

2.49

N.G.

1.37

1.74

.87

Input Rate on “HI” (MJ/h)

Input Rate on “LO” (MJ/h)

L.P.

35.0

8.5

N.G.

35.0

11.0

Orifice sizes for NG equipped appliances

Orifice sizes for LG equipped appliances Front: DMS #50

Front: 1.10 mm Back: DMS #44

Back: DMS #55

This appliance is equipped for installation 0-610 m. For altitudes above 600m, the vent configuration, orifice, or

combination of both may need to be changed. See owner’s manual for information on making these changes.

2012

2013

2011 Feb.

Mar.

Jan. May

Jun.

Apr. Aug.

Sep.

Jul. Nov.

Dec.

Oct.

MANUFACTUREDATE:

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

Manufactured by:Certificate Holder:

www.lopi.com.au

0965

Table of Contents 3

Overview ...........................................................2

Installation Options..........................................6

Heating Specifications.....................................6

Dimensions.......................................................6

Packing List......................................................6

Additional Items Required Direct Vent ..........7

Installation Overview .......................................8

Recommended Installation Procedure ..........8

Fireplace Placement Requirements...............9

Clearances .....................................................9

Raised Fireplaces...........................................9

Minimum Framing Dimensions.....................10

Nailing Brackets............................................11

Corner Installations.......................................12

Gas Line Requirements.................................13

Fuel...............................................................13

Gas Line Connection....................................13

Gas Inlet Pressure........................................13

Gas Line Location.........................................14

Electrical Connection (required) ..................15

Optional Wall Switch or Thermostat

Installation ......................................................16

Parallel ConnectionSeries Connection 16

Vent Requirements ........................................17

Vent Clearances...........................................17

Altitude Considerations.................................17

Approved Vent..............................................18

Vent Installation............................................18

Approved Vent Configurations.....................19

Restrictor Position ........................................19

Exhaust Restrictor Adjustment.....................19

Intake Restrictor Adjustment........................20

Diffuser Plate Adjustment.............................21

Vent Configurations with Horizontal

Termination (EmberFyre Burner only).........22

Vent Configurations with Vertical

Termination (EmberFyre Burner only).........23

Termination Requirements...........................24

Hearth Requirements ....................................25

Facing Requirements ....................................26

Drywall Installation .......................................26

Facing Overview...........................................27

Optional Faceplates – Sizing Chart..............27

Thin Facing Installation (tile, marble, or other

non-combustible under 1" (25mm) thick).....28

Thin Facing Installation (tile, marble, under 1"

(25mm) thick) — Side View..........................29

Thick Facing Installation (stone, brick, or other

non-combustible over 1" (25mm) thick) .......30

Thick Facing with Fireplace Xtrordinair (FPX)

Arched Faces...............................................31

Thick Facing Installation — Side View.........32

Mantel Requirements ....................................33

Combustible Mantels....................................33

Steps for Finalizing the Installation.............34

Air Shutter Adjustment.................................35

Glass Frame Removal and Installation........36

Glass Frame Removal and Installation

(continued) .....................................................37

LP Conversion Instructions..........................38

Installation ..................................................38

Index.............................................................42

4 Safety Precautions

Safety Warnings:

Failure to follow all of the requirements may result in property damage, bodily injury, or even death.

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow ANSI

Z223.1 and NFPA 54(88), in Canada follow CSA B149.1.

A manufactured home (USA only) or mobile home OEM installation must conform with the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4. This

appliance may be installed in Manufactured Housing only after the home is site located.

All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn

from outside the living-area structure. The venting must not be connected to a chimney flue serving a

separate solid-fuel burning appliance.

Notify your insurance company before hooking up this fireplace.

The room heater should be inspected before use and at least annually by a qualified service person.

More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods or

compromise in the installation. Improper installation will void the warranty and safety listing.

This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will

void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about

the type of fuel used to your dealer.

Contact your local building officials to obtain a permit and information on any installation restrictions

or inspection requirements in your area.

If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call

your dealer and arrange for proper servicing.

It is imperative that control compartments, screens, or circulating air passageways of the heater be

kept clean and free of obstructions. These areas provide the air necessary for safe operation.

Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call

your dealer for a full explanation of your heater and what to expect.

Do not store or use gasoline or other flammable liquids in the vicinity of this heater.

Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.

Immediately call a qualified service technician to inspect the appliance and to replace any part of the

control system and any gas control which has been under water.

Do not place clothing or other flammable items on or near the heater. Because this heater can be

controlled by a thermostat there is a possibility of the heater turning on and igniting any items placed

on or near it.

Light the heater using the built-in igniter. Do not use matches or any other external device to light

your heater.

Never remove, replace, modify or substitute any part of the heater unless instructions are given in this

manual. All other work must be done by a trained technician. Don't modify or replace orifices.

The viewing glass should be opened only for conducting service.

Any safety screen or guard removed for servicing must be replaced prior to operating the heater.

Safety Precautions 5

Safety Warnings (continued):

Allow the heater to cool before carrying out any maintenance or cleaning.

Operate the heater according to the instructions included in this manual.

If the main burners do not start correctly turn the gas off and call your dealer for service.

This unit is not for use with solid fuel.

Do not place anything inside the firebox (except the optional artwork).

Warning: Do not operate appliance with the glass front removed, cracked or broken. Replacement

of the glass should be done by a licensed or qualified service person.

Do not throw this manual away. This manual has important operating and maintenance instructions

that you will need at a later time. Always follow the instructions in this manual.

Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical

barrier is recommended if there are at risk individuals in the house. To restrict access to a fireplace

or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals

out of the room and away from hot surfaces.

Children and adults should be alerted to the hazards of high surface temperature and should stay

away to avoid burns or clothing ignition. Do not touch the hot surfaces of the heater. Educate all

children of the danger of a high-temperature heater.

Due to the high temperature, the heater should be located out of traffic and away from furniture and

draperies.

Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.

The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to

shut off.

Travis Industries, Inc. grants no warranty, implied or stated, for the installation or

maintenance of your heater, and assumes no responsibility of any consequential damage(s).

6 Installation (for qualified installers only) 6

Installation Options

Residential or Mobile Home

Straight or Corner Placement

Flush or Recessed Face

Raised or Floor Placement

Internal or External Chase

Bedroom Approved

Heating Specifications

Natural Gas Propane

Approximate Heating Capacity (in square meters)* Up to 158 Up to 158

Maximum MJ Input Per Hour 35.0 35.0

* Heating capacity will vary with floor plan, insulation, and outside temperature.

Dimensions

(a) Center Location of Vent

(b) Heat Shield (must be bent vertically after fireplace is in location)

Packing List

Propane Conversion Kit

30"

762mm

Left

a' gauche

Front

avant

Right

droit

Rear

arrie're

36.25"

921mm

30-1/4"

768mm

33-1/4"

845mm

28-3/4"

730mm

1” 25mm

32.5"

826mm

18.75"

476mm

36-1/2”

928mm

31-3/4”

807mm

6-1/4”

159mm

16-1/2”

426mm

Installation (

for qualified installers only)

564 HO Thimble (250-02318)

Additional Items Required Direct Vent

Gas Line Equipment

Electrical Equipment

This Fireplace Requires a Burner Kit, Firebacks, Logs/Media, and Face/Grill

Burner Style EmberFyre™ Burner

96900116

Firebacks Requires 564 Ceramic

Firebacks:

96100179

96100181

96100182

96100183

96100270

96100271

Logs/Media Included w Burner

Face/Grill Use any 564 Face or Grill

8 Installation (for qualified installers only) 8

Installation Overview

All requirements below must be met.

Recommended Installation Procedure

Frame the opening for the fireplace. Make sure to allow for vent installation.

This fireplace is designed to accommodate 1/2" (13mm) or 5/8" (16mm) drywall (see "Nailing

Brackets" on page 11 for details). Secure the fireplace to the framing.

Install the vent, gas line and electrical hook-up.

Install the drywall.

Install the hearth (if applicable).

Install the facing (if applicable).

Install the mantel (if applicable).

Finalize the installation (see page 33) and install the grill or face.

Drywall

See the section

“Mantel Requirements”

Drywall

Side

Wall 12” min.

305mm

See “Optional Non-

Combustible Facing” See “Optional Non-

Combustible Hearth”

See the section

“Electrical Connection”

See the section

“Vent Requirements”

See the section

“Approved Vent

Configurations”

Nailing brackets

See the section

“Minimum Framing

Dimensions”

See the section

“Gas Line Installation”

Installation (for qualified installers only) 9

Fireplace Placement Requirements

The fireplace requires a 1/2" (13mm) clearance from the angled sides of the fireplace to the framing

members. No material (insulation, framing, etc.) may be placed into this area.

Fireplace must be installed on a level surface capable of supporting the fireplace and vent

Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet)

This heater may be placed in a bedroom. Please be aware of the large amount of heat this appliance

produces when determining a location.

Clearances

When installed, walls in front of the fireplace must be a minimum 12" (305mm) to the side of the

fireplace.

Due to the high temperature, the heater should be located out of traffic and away from furniture and

draperies.

Fireplace must be placed so the vents below and above the glass do not become blocked.

Raised Fireplaces

The fireplace (and hearth, if desired) may be placed on a platform designed to support the fireplace

(155 lbs., 70Kg) and vent.

10 Installation (for qualified installers only) 10

Minimum Framing Dimensions

Minimum enclosure height = 56” (1422.4 mm)

36.75”

936mm

WARNING: A cut-out for the gas line

may be required on the framing. See

the dimensions under “Gas Line

Connection” for details.

The on/off switch/thermostat wire

(if used) should be routed to a location

near the left front of the fireplace.

Route the electrical line to a position

to the left rear of the fireplace.

36.5”

928mm 16.5”

419mm

Andere Handbücher für 564 HO

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 564 DF GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 564 HO Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries Lopi 1250 Republic Bedienungsanleitung

Travis Industries

Travis Industries AGP PI Bedienungsanleitung

Travis Industries

Travis Industries DVL GSR Bedienungsanleitung

Travis Industries

Travis Industries DVL EF II Bedienungsanleitung

Travis Industries

Travis Industries 35 CB Australian Bedienungsanleitung

Travis Industries

Travis Industries 564 SS Deluxe Bedienungsanleitung

Travis Industries

Travis Industries 616 GSR2 Insert Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Travis Industries

Travis Industries 6015 HO GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 864 ST GS Bedienungsanleitung

Travis Industries

Travis Industries 96400539 Bedienungsanleitung

Travis Industries

Travis Industries Avalon Pendleton 745 Bedienungsanleitung

Travis Industries

Travis Industries 430 Ember-Glo GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 1750 Wood Bedienungsanleitung

Travis Industries

Travis Industries Freedom Bay Bedienungsanleitung

Travis Industries

Travis Industries 564 HO GSR2 Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair ProBuilder 54 Linear Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart 2 Fireplace 564 SS GSR2 Bedienungsanleitung

Travis Industries

Travis Industries Revere Fireplace Insert Bedienungsanleitung

Travis Industries

Travis Industries Xtreme 6020 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch