Travis Industries 21 TRV GSR2 Bedienungsanleitung

21 TRV GSR2

Fireplace (w Screen)

Installation Manual

WARNING: FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immediately

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

HOT GLASS WILL CAUSE

BURNS

DO NOT TOUCH GLASS

UNTIL COOLED

NEVER ALLOW CHILDREN

TO TOUCH GLASS

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

Tested and Listed by

ANSI Z21.88-2014

CSA 2.33-2014

Built-In Direct Vent

Fireplace

Natural Gas or Propane

Residential or Mobile

Home

This appliance may be installed in an aftermarket, permanently located, manufactured home

(USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. A conversion

kit is supplied with the appliance.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Travis Industries, Inc. 12521 Harbour Reach Dr., Mukilteo, WA 98275 www.travisproducts.com

2 Introduction

Overview

This manual details the installation requirements

for the 21 TRV GSR2 fireplace. For operating and

maintenance instructions, refer to the 21 TRV

GSR2 Owner's Manual (part # 100-01422).

Listing Details

This appliance was listed by Intertek Test Labs to

ANSI Z21.88. The listing label is attached to the

appliance near the gas control valve. A copy is

shown to the right.

Massachusetts Approval

This manual has been submitted to the

Massachusetts Board of State Examiners of

Plumbers and Gas Fitters.

National Fireplace Institute

Report No. 101423290PRT-001

Control No. 4000515

Vented Gas Fireplace Heater

21 TRV GSR2

Tested to:ANSI Z21.88-2014/CSA 2.33-2014 “Vented Gas Fireplace Heater”, CGA2.17-M91 (R2009) “Gas Burning

Heating Appliances for Manufactured Homes”, and CSAP.4.1-09 Testing method for measuring annual fireplace

efficiency.

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes, CSAB149.1.

This appliance must be installed in accordance with the current Standard CAN/CSA Z240 MH, Mobile Housing,

in Canada or with the Manufactured Home Constructions and Safety Standard, Title 24 CFR, Part 3280, in the

UnitedStates,orwhensuchastandardisnotapplicable,ANSI/NCSBCSA225.1/NFPA501A, Manufactured Home

Installation Standard.

Thisventedgas fireplace heater is equippedatthe factory for use withnaturalgas. If conversion to propane(LP)

is desired, the optional factory conversion kit must be used. Part No. 250-02376 (SIT) or 225-20231 & 225-20173

(PSE) register kit may be used.

This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an

aftermarket,permanentlylocated, manufactured home (USAonly)ormobile home, where not prohibited by local

codes. See owner’s manual for details. This appliance is not convertible for use with other gases, unless a

certified kit is used.

This vented gas fireplace heater is not for use with air filters.

Keep burner and control compartment clean. See installation and operating instructions accompanying

appliance.

This appliance must be properly connected to a venting system in accordance with the manufacturer’s

installation instructions. Use only approved coaxial direct vent system to vent this appliance to the exterior. See

owner’s manual for approved brands of venting.

If the vent-air intake system is disconnected for servicing or any other reason, it must be resealed and / or

reinstalled.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property

damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional

information consult a qualified installer, service agency or the gas supplier.

VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUEL

Minimum Clearances to Combustibles

Fireplace to Adjacent Wall

Wood Floor Beneath Fireplace

Back and Angled Sides to Enclosure

1” (26mm)

0” (0mm)

0.5” (13mm)

Top and Sides to Enclosure

Base of Fireplace to a Mantel 0” (0mm)

See Owner’s Manual

FAN TYPE VENTED CIRCULATOR

Blower Electrical Rating: 115V., 1.5Amps, 60 Hz

Part No. 99000163 fan or blower assembly may be used

Minimum Inlet Pressure (inches W.C.)

Maximum Inlet Pressure (inches W.C.)

Manifold Pressure on “HI” (inches W.C.)

L.P.

11”

13”

10”

N.G.

5.5”

7”

3.5”

Input Rate on “HI” (BTU/Hr)

Input Rate on “LO” (BTU/Hr)

Orifice Size - Front (DMS)

Orifice Size - Rear (DMS)

L.P.

16,500

5,000

#67

#66

N.G.

16,500

6,000

#55

This appliance is equipped for use only at altitudes 0-2,000 feet (0-610m) in the USA. In Canada, 0-4,500 feet (0-1370m).

For altitudes above 2,000 feet, the vent configuration, orifice, or combination of both may need to be changed.

See owner’s manual for information on making these changes.

2015

2016

2014

Feb.

Mar.

Jan.

May

Jun.

Apr.

Aug.

Sep.

Jul.

Nov.

Dec.

Oct.

MANUFACTURE DATE:

WARNING: Failure to install this appliance per the manufacturer’s instructions or failure to use only parts

specifically approved with this appliance may result in property damage or personal injury.

12521 Harbour Reach Drive

Mukilteo, WA 98275

Manufactured by:

www.travisproducts.com

CAUTION:

Do not operate this appliance with glass removed, cracked or broken. Replacement of the panel(s) should be done

by a licensed or qualified service person.

0929

Table of Contents 3

Travis Industries 4150309 100-01421

Table of Contents

OVERVIEW.....................................................2

LISTING DETAILS..........................................2

TABLE OF CONTENTS..................................3

INSTALLATION OPTIONS.............................6

HEATING SPECIFICATIONS.........................6

DIMENSIONS..................................................6

PACKING LIST...............................................7

ADDITIONAL ITEMS REQUIRED..................7

RECOMMENDED INSTALLATION

PROCEDURE .................................................7

INSTALLATION OVERVIEW – TOP VENT

CONFIGURATION..........................................8

INSTALLATION OVERVIEW – REAR VENT

CONFIGURATION..........................................9

MASSACHUSETTS REQUIREMENTS........10

Requirements for the Commonwealth of

Massachusetts .................................................. 10

MANUFACTURER REQUIREMENTS .............. 10

TOP VENT OR REAR VENT

CONFIGURATION........................................11

Converting the Fireplace to Rear Vent

Configuration ..................................................... 11

Converting the Fireplace to Rear Vent (continued)12

Converting the Fireplace to Rear Vent (continued)13

FIREPLACE PLACEMENT REQUIREMENTS14

Clearances ........................................................ 14

Raised Fireplaces.............................................. 14

Minimum Framing Dimensions - Top Vent

Configuration ..................................................... 15

Minimum Framing Dimensions - Rear Vent

Configuration ..................................................... 16

TELEVISIONS PLACED ABOVE THE

FIREPLACE..................................................17

Using a Mantel Between the Fireplace and

Television .......................................................... 17

NAILING BRACKETS...................................18

CORNER INSTALLATIONS - TOP VENT

CONFIGURATION........................................19

CORNER INSTALLATIONS - REAR VENT

CONFIGURATION........................................19

OUTDOOR FIREPLACE INSTALLATIONS.20

GAS LINE REQUIREMENTS.......................21

Fuel ................................................................... 21

Gas Line Connection ......................................... 21

Gas Inlet Pressure............................................. 21

Optional Gas Line Location ............................... 22

Gas Line Location ............................................. 22

ELECTRICAL CONNECTION (REQUIRED)23

VENT REQUIREMENTS ..............................24

Vent Clearances ................................................ 24

Altitude Considerations ..................................... 24

Approved Vent .................................................. 25

Vent Installation ................................................. 25

APPROVED VENT CONFIGURATIONS.....26

Restrictor Position ............................................. 26

Exhaust Restrictor Adjustment .......................... 26

Diffuser Plate Adjustment .................................. 27

TOP VENT CONFIGURATION WITH

HORIZONTAL TERMINATION ....................28

TOP VENT CONFIGURATION WITH

VERTICAL TERMINATION..........................29

REAR VENT CONFIGURATION WITH

HORIZONTAL TERMINATION ....................30

REAR VENT CONFIGURATION WITH

VERTICAL TERMINATION..........................31

TERMINATION REQUIREMENTS...............32

HEARTH REQUIREMENTS.........................33

FACING REQUIREMENTS..........................34

Face Dimensions............................................... 34

Facing Detail – Drywall (or other 1/2” thick facing)34

FACING DETAIL – TILE FACING................35

MANTEL REQUIREMENTS.........................36

STEPS FOR FINALIZING THE

INSTALLATION............................................37

Air Shutter Adjustment ...................................... 38

BARRIER REMOVAL...................................39

GLASS FRAME REMOVAL AND

INSTALLATION............................................40

GLASS FRAME REMOVAL AND

INSTALLATION (CONTINUED)...................41

LOG SET INSTALLATION...........................42

Rear Log Installation ......................................... 42

Right Log Installation ......................................... 43

Right Twig Installation ....................................... 43

Left Twig Installation.......................................... 44

Log Installation Overview .................................. 44

LP CONVERSION INSTRUCTIONS............45

LINER INSTALLATION ADDENDA.............50

WIRING DIAGRAM ......................................51

Index ................................................................. 52

4 Safety Precautions

Travis Industries 4150309 100-01421

Safety Warnings

 Failure to follow all of the requirements may result in property damage, bodily injury, or even death.

Young children should be carefully supervised when they are in the same room

as the appliance. Toddlers, young children and others may be susceptible to

accidental contact burns. A physical barrier is recommended if there are at risk

individuals in the house. To restrict access to a fireplace or stove, install an

adjustable safety gate to keep toddlers, young children and other at risk

individuals out of the room and away from hot surfaces.

Children and adults should be alerted to the hazards of high surface temperature

and should stay away to avoid burns or clothing ignition. Do not touch the hot

surfaces of the heater. Educate all children of the danger of a high-temperature

heater.

Due to the high temperature, the heater should be located out of traffic and away

from furniture and draperies.

 This unit must be installed by a qualified installer to prevent the possibility of an explosion.

 This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow ANSI

Z223.1 and NFPA 54(88), in Canada follow CSA B149.1.

 A manufactured home (USA only) or mobile home OEM installation must conform with the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4. This

appliance may be installed in Manufactured Housing only after the home is site located.

 All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn

from outside the living-area structure. The venting must not be connected to a chimney flue serving a

separate solid-fuel burning appliance.

 Notify your insurance company before hooking up this fireplace.

 The instructions in this manual must be strictly adhered to. Do not use makeshift methods or

compromise in the installation. Improper installation will void the warranty and safety listing.

 This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will

void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about

the type of fuel used to your dealer.

 Contact your local building officials to obtain a permit and information on any installation restrictions

or inspection requirements in your area.

 If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call

your dealer and arrange for proper servicing.

 It is imperative that control compartments, screens, or circulating air passageways of the heater be

kept clean and free of obstructions. These areas provide the air necessary for safe operation.

 Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call

your dealer for a full explanation of your heater and what to expect.

 Do not store or use gasoline or other flammable liquids in the vicinity of this heater.

 Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.

Immediately call a qualified service technician to inspect the appliance and to replace any part of the

control system and any gas control which has been under water.

Safety Precautions 5

Travis Industries 4150309 100-01421

Safety Warnings (continued)

 Because this heater can be controlled by a thermostat there is a possibility of the heater turning on

and igniting any items placed on or near the appliance.

 Light the heater using the built-in igniter. Do not use matches or any other external device to light

your heater.

 Never remove, replace, modify or substitute any part of the heater unless instructions are given in this

manual. All other work must be done by a trained technician. Don't modify or replace orifices.

 The viewing glass should be opened only for conducting service.

 Allow the heater to cool before carrying out any maintenance or cleaning.

 Operate the heater according to the instructions included in this manual.

 If the main burners do not start correctly turn the gas off and call your dealer for service.

 This unit is not for use with solid fuel.

 Do not place anything inside the firebox (except the optional artwork).

 Warning: Do not operate appliance with the glass front removed, cracked or broken. Replacement

of the glass should be done by a licensed or qualified service person.

 Do not throw this manual away. This manual has important operating and maintenance instructions

that you will need at a later time. Always follow the instructions in this manual.

 Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.

The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to

shut off.

 A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this

appliance and shall be installed for the protection of children and other at-risk individuals.

 If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this

appliance.

 Clothing or other flammable material should not be placed on or near the appliance.

 Any safety screen, guard, or barrier removed for servicing an appliance must be replaced prior to

operating the appliance.

 Installation and repair should be done by a qualified service person. The appliance should be

inspected before use and at least annually by a professional service person. More frequent cleaning

might be required due to excessive lint from carpeting, bedding material, et cetera. It is imperative

that control compartments, burners, and circulating air passageways of the appliance be kept clean.

 Travis Industries, Inc. grants no warranty, implied or stated, for the installation or

maintenance of your heater, and assumes no responsibility of any consequential damage(s).

Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of combustion of such

fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm.

California Health & Safety Code Sec. 25249.6

6 Features and Specifications

Travis Industries 4150309 100-01421

Installation Options

 Residential or Mobile Home

 Straight or Corner Placement

 Flush or Recessed Face

 Raised or Floor Placement

 Internal or External Chase

 Horizontal or Vertical Vent

 Bedroom Approved

Heating Specifications

Natural Gas Propane

Approximate Heating Capacity (in square feet)* Up to 650 Up to 650

Maximum BTU Input Per Hour 16,500 16,500

* Heating capacity will vary with floor plan, insulation, and outside temperature.

Dimensions

35.875"

8" External Diameter

13.625"*

45°

20.125"

See "Gas Line

Requirements" for

Details on the Gas Inlet

7.5"*

4.875"

Nailing Brackets

Nailing

Bracket

(Framing)

27.25"

Rear Vent Configuration

8.5"

12.375"*

Top Vent Configuration

Lifting Bracket (may

be bent down) 34.125"

* See "Clearances" and "Framing Dimensions" for details.

NOTE: 0.5" clearance is required to the angled sides and rear of the fireplace.

Installation (for qualified installers only) 7

Travis Industries 4150309 100-01421

Packing List

 Propane Conversion Kit (Orifices, Rivet)

 Log Set

 Firestop (sku 93006094)



Rear Vent Configuration Kit (insulation)

 (4) AA Batteries, (1) 9-Volt Battery

 Remote Control

 Felt Tabs (for concealment cover)

Additional Items Required

 If using LP (propane) a conversion kit is required (sku 94400999 – GSR Stepper Motor Kit).

 Direct Vent

 Gas Line Equipment (shutoff valve, pipe, etc.)

 Electrical Equipment (min. 14 gauge, grounded line)

Recommended Installation Procedure

HINT: We strongly recommend installing all of the optional equipment before placing the fireplace.

Place the fireplace on a suitable work stand to ease installation.

 Install the optional equipment (do not install the logs) – we recommend the following order:

a) LP Conversion (if applicable) – NOTE: leave the burner removed until after the liner is

installed (if applicable). If using the GreenSmart remote, install the modulating regulator

during LP conversion.

b) Liner (if applicable) – NOTE: You will need to loosen the accent light bracket while installing

the liner (see page 50).

c) Blower

NOTE: Do not install the rheostat if using the GreenSmart remote.

e) Remote

 Frame the opening for the fireplace. Make sure to allow for vent installation.

 This fireplace is designed to accommodate 1/2" drywall or 1/2” drywall with 3/8” tile (see "Nailing

Brackets" on page 17 for details). Secure the fireplace to the framing.

NOTE: If the facing is not 1/2" or 7/8" thick, follow the directions below:

Place a strip of facing material to both sides of the fireplace opening (NOTE: the strips will be

removed after the fireplace is secured). The facing thickness must represent the total thickness

of the finished facing (e.g.: If tile is to be used, include the thickness of the backboard, tile, and

tile adhesive). Insert the fireplace into the framing. Slide it back until the front edge of the

fireplace is flush with the facing material. Secure the fireplace using the plates located along the

base of the fireplace.

 Complete the gas line installation. Complete the electrical hook-up.

 Complete the vent installation.

 Install the hearth (if applicable).

 Install the drywall and facing (if applicable).

 Install the mantel (if applicable).

 Finalize the installation (see page 37) and install the grill or face.

8 Installation (for qualified installers only)

Travis Industries 4150309 100-01421

Installation Overview – Top Vent Configuration

 All requirements below must be met.

See the section

"Termination

Requirements"



















Drywall

Gas Line

(left side or beneath)

See the section

"Mantel Requirements"

See the section

"Vent Requirements"

See the section "Minimum

Framing Dimensions"

See the section

"Hearth Requirements"

See the section "Electrical Connection"

1" Min. Clearance from Face to Side Wall

Installation (for qualified installers only) 9

Travis Industries 4150309 100-01421

Installation Overview – Rear Vent Configuration

 All requirements below must be met.



See the section "Acceptable

Vent Lengths"

See the section

"Gas Line Installation"

See the section

"Electrical

Connection"

See the section

"Mantel Requirements"

1" Min.

(from face)

See the section

"Vent Requirements"

See the section "Minimum

Framing Dimensions"

See the section

"Hearth Requirements"

Drywall

See the section

"Termination Requirements"

10 Installation (for qualified installers only)

Travis Industries 4150309 100-01421

Massachusetts Requirements

NOTE: The following requirements reference various Massachusetts and national codes not contained in this document.

Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in

part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent

termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and

porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall

observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the

gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard

wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served

by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the

services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired

carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall

have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day

period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be

ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight

(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or

equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP

CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation

unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the

provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54

as adopted by the Board; and

• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the

dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or

venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment

and the venting system shall include:

• Detailed instructions for the installation of the venting system design or the venting system components; and

• A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts

for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the

manufacturer:

• The referenced “special venting system” instructions shall be included with the appliance or equipment installation

instructions; and

• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a

parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting

instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or

equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Andere Handbücher für 21 TRV GSR2

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 564 LedgeStone Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Cypress Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV GS2 Bedienungsanleitung

Travis Industries

Travis Industries 616 Diamond-Fyre GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 616 Diamond-Fyre GSR Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB Bedienungsanleitung

Travis Industries

Travis Industries DVL Insert Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries Freedom Bay Bedienungsanleitung

Travis Industries

Travis Industries DVS Insert EF II Bedienungsanleitung

Travis Industries

Travis Industries 36 CF II Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair ProBuilder 54 Linear Bedienungsanleitung

Travis Industries

Travis Industries LOPI X Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Deluxe Bedienungsanleitung

Travis Industries

Travis Industries 864 See Through Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Log Set Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV GS Bedienungsanleitung

Travis Industries

Travis Industries Small Flush Bedienungsanleitung

Travis Industries

Travis Industries Granite 99600200 Service-Handbuch

Travis Industries

Travis Industries 430 GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB GSR2 Bedienungsanleitung

Travis Industries

Travis Industries DVS GSR2 NB Insert Bedienungsanleitung

Travis Industries

Travis Industries Flush Wood Insert Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch