Travis Industries 564 HO GSR2 Bedienungsanleitung

564 HO GSR2

Fireplace

with Screen (AU)

Listed by

AS 4553-2008 GMK10022

IAPMO-R&T OCEANA

Built-In Direct Vent Fireplace

Natural Gas or Propane



Residential or Mobile Home

WARNING: If the information in these instructions is not followed exactly, a fire or explosion

may result causing property damage, personal injury or loss of life.



DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.



DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.



DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.



DO NOT MODIFY THIS APPLIANCE.



Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

This appliance may be installed in

an aftermarket permanently

located, manufactured home (USA

only) or mobile home, where not

prohibited by local codes.

This appliance is only for use

with the type(s) of gas indicated

on the rating plate. A conversion

kit is supplied with the appliance.

Installation Manual

Installer: After installation give this manual to the home-

owner and explain operation of this heater.

Dragon Wholesaling Pty. Ltd.

Unit 4, 16 Lexington Drive

Bella Vista NSW 2153

Australia

2 Introduction

Overview

This manual details the installation requirements for

the 564 HO NB GSR2 fireplace. For operating and

maintenance instructions, refer to the 564 HO NB

GSR2 Owner's Manual (part # 100-01415).

IAPMO-R&T

OCEANA

Gas Mark

GMK10022_02

564 HO GSR2 (Au)

Vented Gas Fireplace Heater

Tested to the combustion performance and construction requirements of AS 4553-2008 Gas Space Heating

Appliances. This appliance must be installed in accordance with all local codes.

This 564 HO GSR2 appliance is equipped from the factory only for use with Natural Gas and is only for use

with the type of gas indicated on the rating plate. For conversion to LP (Propane) use a certified kit

supplied by the manufacturer. See owner’s manual for information on making these changes.

This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home where

not prohibited by local codes.

This vented gas fireplace heater is not for use with air filters. This appliance must be properly connected to

a venting system in accordance with the manufacturer’s installation instructions. Use only approved

coaxial direct vent systems to vent this appliance to the exterior. See owner’s manual for approved brands

of venting.

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause injury or

property damage. Refer to the owner’s information manual provided with this appliance. For assistance or

additional information consult a qualified installer, service agency or the gas supplier.

This appliance is a Vented Gas Fireplace Heater. Not for use with Solid Fuel.

Young children should be carefully supervised at all times when they are in the same room

as the appliance.

Fireplace to adjacent wall

Side to enclosure

Back to enclosure

305 mm

13 mm

0 mm

Base of fireplace to enclosure top

Combustible floor under fireplace

Base of fireplace to a mantel

1423 mm

0 mm

See Owner’s Manual

Minimum Clearances to Combustibles

FAN TYPE VENTED CIRCULATOR

Blower Electrical Rating: 240V., 1.5 Amps, 50 Hz, 150 Watts

Minimum Inlet Pressure (kPa)

Maximum Inlet Pressure (kPa)

Manifold Pressure on “HI” (kPa)

L.P.

2.74

3.24

2.74

N.G.

1.13

1.74

.87

Input Rate on “HI” (MJ/h)

Input Rate on “LO” (MJ/h)

Orifice Size - Front (DMS)

Orifice Size - Rear (DMS)

L.P.

36.9

7.9

1.1mm

#55

N.G.

36.9

10.97

#50

#44

This appliance is equipped for installation 0-610 m. For altitudes above 600m, the vent configuration, orifice, or

combination of both may need to be changed. See owner’s manual for information on making these changes.

2015

2016

2014

Feb.

Mar.

Jan.

May

Jun.

Apr.

Aug.

Sep.

Jul.

Nov.

Dec.

Oct.

MANUFACTURE DATE:

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

Manufactured by: Certificate Holder:

www.lopi.com.au

Dragon Wholesaling Pty. Ltd.

Unit 4, 16 Lexington Drive

Bella Vista NSW 2153

Australia

0965

Table of Contents 3

Overview ...........................................................2

Installation Options..........................................6

Heating Specifications.....................................6

Dimensions.......................................................6

Packing List......................................................7

Additional Items Required...............................7

Installation Overview .......................................8

Recommended Installation Procedure ..........8

Fireplace Placement Requirements...............9

Clearances .....................................................9

Raised Fireplaces...........................................9

Minimum Framing Dimensions.....................10

Nailing Brackets............................................11

Corner Installations.......................................12

Gas Line Requirements.................................13

Fuel...............................................................13

Gas Line Connection....................................13

Gas Inlet Pressure........................................13

Gas Line Location.........................................14

Converting Gas Line to the Left Side ...........14

Electrical Connection (required) ..................15

Vent Requirements ........................................16

Vent Clearances...........................................16

Altitude Considerations.................................16

Approved Vent..............................................17

Vent Installation............................................17

Approved Vent Configurations.....................18

Restrictor Position ........................................18

Exhaust Restrictor Adjustment.....................18

Intake Restrictor Adjustment ........................19

Diffuser Plate Adjustment.............................20

Vent Configurations with Horizontal

Termination (EmberFyre Burner only).........21

Vent Configurations with Vertical

Termination (EmberFyre Burner only).........22

Vent Configurations with Horizontal

Termination (Dancing/DiamondFyre)...........23

Vent Configurations with Vertical

Termination (Dancing/DiamondFyre)...........24

Termination Requirements...........................25

Hearth Requirements ....................................26

Facing Requirements ....................................27

Drywall Installation .......................................27

Facing Overview...........................................30

Optional Faceplates – Sizing Chart..............30

Thin Facing Installation (tile, marble, or other

non-combustible under 1" (25mm) thick).....31

Thin Facing Installation (tile, marble, under 1"

(25mm) thick) — Side View..........................32

Thick Facing Installation (stone, brick, or other

non-combustible over 1" (25mm) thick) .......33

Thick Facing with Fireplace Xtrordinair (FPX)

Arched Faces...............................................34

Thick Facing Installation — Side View.........35

Mantel Requirements ....................................36

Mantel Column Clearances..........................36

Steps for Finalizing the Installation.............37

Air Shutter Adjustment.................................38

Barrier Removal.............................................39

Glass Frame Removal ...................................40

Glass Frame Removal and Installation

(continued) .....................................................41

LP Conversion Instructions..........................42

Installation ..................................................42

4 Safety Precautions

Safety Warnings

Failure to follow all of the requirements may result in property damage, bodily injury, or even death.

Young children should be carefully supervised when they are in the same room

as the appliance. Toddlers, young children and others may be susceptible to

accidental contact burns. A physical barrier is recommended if there are at risk

individuals in the house. To restrict access to a fireplace or stove, install an

adjustable safety gate to keep toddlers, young children and other at risk

individuals out of the room and away from hot surfaces.

Children and adults should be alerted to the hazards of high surface temperature

and should stay away to avoid burns or clothing ignition. Do not touch the hot

surfaces of the heater. Educate all children of the danger of a high-temperature

heater.

Due to the high temperature, the heater should be located out of traffic and away

from furniture and draperies.

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow ANSI

Z223.1 and NFPA 54(88), in Canada follow CSA B149.1.

A manufactured home (USA only) or mobile home OEM installation must conform with the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4. This

appliance may be installed in Manufactured Housing only after the home is site located.

All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn

from outside the living-area structure. The venting must not be connected to a chimney flue serving a

separate solid-fuel burning appliance.

Notify your insurance company before hooking up this fireplace.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods or

compromise in the installation. Improper installation will void the warranty and safety listing.

This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will

void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about

the type of fuel used to your dealer.

Contact your local building officials to obtain a permit and information on any installation restrictions

or inspection requirements in your area.

If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call

your dealer and arrange for proper servicing.

It is imperative that control compartments, screens, or circulating air passageways of the heater be

kept clean and free of obstructions. These areas provide the air necessary for safe operation.

Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call

your dealer for a full explanation of your heater and what to expect.

Do not store or use gasoline or other flammable liquids in the vicinity of this heater.

Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.

Immediately call a qualified service technician to inspect the appliance and to replace any part of the

control system and any gas control which has been under water.

Because this heater can be controlled by a thermostat there is a possibility of the heater turning on

and igniting any items placed on or near the appliance.

Safety Precautions 5

Safety Warnings (continued)

Light the heater using the built-in igniter. Do not use matches or any other external device to light

your heater.

Never remove, replace, modify or substitute any part of the heater unless instructions are given in this

manual. All other work must be done by a trained technician. Don't modify or replace orifices.

The viewing glass should be opened only for conducting service.

Allow the heater to cool before carrying out any maintenance or cleaning.

Operate the heater according to the instructions included in this manual.

If the main burners do not start correctly turn the gas off and call your dealer for service.

This unit is not for use with solid fuel.

Do not place anything inside the firebox (except the optional artwork).

Warning: Do not operate appliance with the glass front removed, cracked or broken. Replacement

of the glass should be done by a licensed or qualified service person.

Do not throw this manual away. This manual has important operating and maintenance instructions

that you will need at a later time. Always follow the instructions in this manual.

Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.

The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to

shut off.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this

appliance and shall be installed for the protection of children and other at-risk individuals.

If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this

appliance.

Clothing or other flammable material should not be placed on or near the appliance.

Any safety screen, guard, or barrier removed for servicing an appliance must be replaced prior to

operating the appliance.

Installation and repair should be done by a qualified service person. The appliance should be

inspected before use and at least annually by a professional service person. More frequent cleaning

might be required due to excessive lint from carpeting, bedding material, et cetera. It is imperative

that control compartments, burners, and circulating air passageways of the appliance be kept clean.

Travis Industries, Inc. grants no warranty, implied or stated, for the installation or

maintenance of your heater, and assumes no responsibility of any consequential damage(s).

SAFETY WARNINGS:

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.

DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN

OPERATION.

DO NOT MODIFY THIS APPLIANCE.

THIS INSTALLATION MUST CONFORM WITH THE FOLLOWING:

Manufacturer’s Installation instructions

Local Gas Fitting Regulations

Municipal Building Codes,

Refer to AS/NZS 5601.1 for Gas Installations.

S.A.A. Wiring Code

Local Electrical Regulations

Any other statutory regulations

NOT SUITABLE FOR MARINE USE.

NOT INTENDED FOR FIREPLACE INSERT.

APPLIANCES INCORPORATING A LIVE FUEL EFFECT, AND DESIGNED TO OPERATE

6 Installation (for qualified installers only) 6

Installation Options

Residential or Mobile Home

Straight or Corner Placement

Flush or Recessed Face

Accent Lights

Raised or Floor Placement

Internal or External Chase

Bedroom Approved

Heating Specifications

Natural Gas Propane

Approximate Heating Capacity (in square meters)* Up to 158 Up to 158

Maximum MJ Input Per Hour 36.9 36.9

* Heating capacity will vary with floor plan, insulation, and outside temperature.

Dimensions

36.25"

921mm

Weight: 165 Lbs. (74 kg)



18.25" *

464mm

28" *

712mm

30.25"

768mm

33.25"

845mm

25mm

28.75"

730mm

18.875"

480mm

31-3/4"

807mm

8" (203mm) Diameter Vent

6.25"

159mm

32.75"

832mm

* See "Clearances" and "Framing Dimensions" for details.

Left

a' gauche

Front

avant

Right

droit

Rear

arrie're

36.25"

928mm

Heat Shield

(must be bent vertically after fireplace is in location)

Installation (

for qualified installers only)

Packing List

Propane Conversion Kit

564 HO Thimble (250-02318)



Remote Control

Additional Items Required

If using LP (propane) a conversion kit is required (sku 94400999 – GSR Stepper Motor Kit).

Gas Line Equipment

Electrical Equipment

This Fireplace Requires a Burner Kit, Firebacks, Logs/Media, and Face/Grill

This fireplace is shipped without a burner. This allows the fireplace to be configured in one of three

unique designs. See the table below to verify you have all of the items required.

Burner Style EmberFyre™ Burner

96900116 DiamondFyre™

Burner

96900115

DancingFyre™ Burner

96900114

Firebacks Requires 564 Ceramic

Firebacks:

96100179

96100181

96100182

96100183

96100270

96100271

Requires one of the

following:

Stainless 96100249

Enamel Black 96100250

Painted Black 96100251

Included w Burner

(Black Painted)

NOTE: You may use

ceramic or 564 HO

DiamondFyre firebacks,

but they are only installed

on the firebox walls (floor

firebacks are discarded).

Logs/Media Included w Burner Use 564 HO (31 DVI)

Media

Driftwood (94500548)

Fyre-Stones (94700730)

Included w Burner

Face/Grill Use any 564 Face or Grill Use any 564 Face or Grill Use any 564 Face or Grill

8 Installation (for qualified installers only) 8

Installation Overview

All requirements below must be met.

Recommended Installation Procedure

Frame the opening for the fireplace. Make sure to allow for vent installation.

This fireplace is designed to accommodate 1/2" (13mm) or 5/8" (16mm) drywall (see "Nailing

Brackets" on page 11 for details). Secure the fireplace to the framing.

Install the vent, gas line and electrical hook-up.

Install the drywall.

Install the hearth (if applicable).

Install the facing (if applicable).

Install the mantel (if applicable).

Finalize the installation (see page 36) and install the grill or face.

Drywall

See the section

“Mantel Requirements”

Drywall

Side

Wall 12” min.

305mm

See “Optional Non-

Combustible Facing” See “Optional Non-

Combustible Hearth”

See the section

“Electrical Connection”

See the section

“Vent Requirements”

See the section

“Approved Vent

Configurations”

Nailing brackets

See the section

“Minimum Framing

Dimensions”

See the section

“Gas Line Installation”

Installation (for qualified installers only) 9

Fireplace Placement Requirements

The fireplace requires a 1/2" (13mm) clearance from the angled sides of the fireplace to the framing

members. No material (insulation, framing, etc.) may be placed into this area.

Fireplace must be installed on a level surface capable of supporting the fireplace and vent

Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet)

This heater may be placed in a bedroom. Please be aware of the large amount of heat this appliance

produces when determining a location.

Clearances

When installed, walls in front of the fireplace must be a minimum 12" (305mm) to the side of the

fireplace.

Due to the high temperature, the heater should be located out of traffic and away from furniture and

draperies.

Fireplace must be placed so the vents below and above the glass do not become blocked.

Raised Fireplaces

The fireplace (and hearth, if desired) may be placed on a platform designed to support the fireplace

(165 lbs., 74Kg) and vent.

The base of the fireplace must be a minimum 70” (1778mm) below the room ceiling.

10 Installation (for qualified installers only) 10

Minimum Framing Dimensions

(a) Minimum Enclosure Height

36.5"

928mm

36.75"

936mm

17.75"

451mm

56"

1423mm

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 864 HO NB GSR2 Bedienungsanleitung

Travis Industries

Travis Industries EmberGlo 616 Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries Large Flush Bedienungsanleitung

Travis Industries

Travis Industries Xtreme 6020 Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 616 Diamond-Fyre GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 864 Clean Face Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair ProBuilder 54 Linear Bedienungsanleitung

Travis Industries

Travis Industries 42 ProBuilder MV Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries 864 See Through Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries 21 DV RV Bedienungsanleitung

Travis Industries

Travis Industries 1250 Insert Bedienungsanleitung

Travis Industries

Travis Industries 864 HH Bedienungsanleitung

Travis Industries

Travis Industries Cleanface 864 Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Travis Industries

Travis Industries Revere Fireplace Insert Bedienungsanleitung

Travis Industries

Travis Industries Lopi 1250 Republic Bedienungsanleitung

Travis Industries

Travis Industries ProBuilder 54 Linear Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch